hh3cDot11RRMCfgIntrfThres
HH3C-DOT11-RRM-MIB ·
.1.3.6.1.4.1.25506.2.75.8.1.2.1.9
Object
column
r/w
percent Integer32
Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.
Context
- MIB
- HH3C-DOT11-RRM-MIB
- OID
.1.3.6.1.4.1.25506.2.75.8.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Units
- percent
- Parent
- hh3cDot11RRMRadioCfgEntry
- Table
- hh3cDot11RRMRadioCfgTable
- Siblings
- 12
Syntax
percent Integer32
Values & Constraints
Object Constraints
range: 1-100
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hh3cDot11RRMRadioType 802.11 radio type. | column | HH3C-DOT11-REF-MIBHh3cDot11RadioType | .1.3.6.1.4.1.25506.2.75.8.1.2.1.1 |
| hh3cDot11RRMCfgNoiseThres Configure the noise threshold. | column | Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.10 |
| hh3cDot11RRMCfgPERThres Configure the CRC error threshold.
If the percentage of CRC errors reaches the threshold, RRM will perform
resource adjustment to control the situation. | column | percent Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.11 |
| hh3cDot11RRMCfgToleranceFctr Configure the tolerance level.
During dynamic frequency selection (DFS), the channel will be changed
only if there is a better channel having lesser interference and packet
error … | column | percent Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.12 |
| hh3cDot11RRMCfgAdjacencyFctr Configure the adjacency factor for the band.
If transmit power control (TPC) is configured, power will be adjusted
when the nth neighbor is detected. The value n is the adjacency… | column | Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.13 |
| hh3cDot11RRMCfgChlState Enable/Disable dynamic channel selection. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.25506.2.75.8.1.2.1.2 |
| hh3cDot11RRMCfgChlMode Configure the mode of channel selection.
This node can be configured only when dynamic channel selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.25506.2.75.8.1.2.1.3 |
| hh3cDot11RRMChlProntoRadioElmt Specify the AP and radio that will change channel at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of c… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.4 |
| hh3cDot11RRMCfgPwrState Enable/Disable dynamic power selection for the band. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.25506.2.75.8.1.2.1.5 |
| hh3cDot11RRMCfgPwrMode Configure the mode of transmit power control.
This node can be configured only when dynamic power selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.25506.2.75.8.1.2.1.6 |
| hh3cDot11RRMPwrProntoRadioElmt Specify the AP and radio that will change power at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of tra… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.7 |
| hh3cDot11RRMCfgIntrvl Configure the calibration interval. | column | minute SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.8 |