hardwareFactoryResetButton

G6-HARDWARE-MIB · .1.3.6.1.4.1.3181.10.6.1.31.5
MIB view Table view

Object

scalar r/w Enumeration 
When disabled the factory button will trigger the factory reset function when pressed for a long time. The IP discover function upon a short button click is not affected.

Context

MIB
G6-HARDWARE-MIB
OID
.1.3.6.1.4.1.3181.10.6.1.31.5
Type
scalar
Access
readwrite
Status
current
Parent
hardware
Siblings
23

Syntax

Enumeration

Values & Constraints

Enumerated Values
0disabled
1enabled

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
hardwareLedTest
Runs a leds test whereby all LED light up in all possible colors for checking their function. The tests terminates within a few seconds.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.3181.10.6.1.31.1
hardwarePowerSupply1Status
Displays state of primary supply or only supply for single supply systems.
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.100
hardwarePowerSupply2Status
Displays state of secondary supply if available.
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.101
hardwareRunningOnPoe
When set the unit currently operates on the PD input via PoE.
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.102
hardwareFanStatus
Displays state of cooling fan. Indicates UNUSED in fanless devices.
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.103
hardwareSdCardStatus
Current status of SD-card.
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.104
hardwareNumOfPorts
Total number of Ethernet ports this hardware offers.
scalarInteger32.1.3.6.1.4.1.3181.10.6.1.31.105
hardwareMaskOfExistingPorts
Set bit for each port that physically exisiting and could be in use.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.3181.10.6.1.31.106
hardwareMaskOfSfpPorts
Marks which ports support SFPs.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.3181.10.6.1.31.107
hardwareMaskOfPoePorts
Marks which ports support PoE output.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.3181.10.6.1.31.108
moduleInfoTable
This section indicates which modules are inserted in the optional extension slots.
table-.1.3.6.1.4.1.3181.10.6.1.31.109
slotInfoTable
This section indicates which modules are inserted in the optional extension slots.
table-.1.3.6.1.4.1.3181.10.6.1.31.110
portInfoTable
Used to map physical to logical port ids.
table-.1.3.6.1.4.1.3181.10.6.1.31.111
portLedsTable
This section indicates the state of all port related LEDs.
table-.1.3.6.1.4.1.3181.10.6.1.31.112
deviceLedsTable
This section indicates the state of all LEDs which are not port related. Please note: Not every unit offers all LEDs.
table-.1.3.6.1.4.1.3181.10.6.1.31.113
cableTestStatusTable
This table display the result of the last cable test. Values are only available for copper ports while a link is down and if the cable test function is enabled.
table-.1.3.6.1.4.1.3181.10.6.1.31.114
ioSignalStatusTable
This section is only used for devices which offer external signal inputs and outputs.
table-.1.3.6.1.4.1.3181.10.6.1.31.115
tcamStatusTable
The TCAM is a programmable wire speed packet filter. The filter is controlled by the system automatically. This table indicates which filters have been set.
table-.1.3.6.1.4.1.3181.10.6.1.31.116
hardwareLedMode
The LED display can be configured to be less intrusive.
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.2
hardwarePowerSupply1Monitored
When disabled a missing power supply 1 will not turn the associated led red on failure. Do this when single power supply 2 operation is used or when the device is powered soley by…
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.3
hardwarePowerSupply2Monitored
When disabled a missing power supply 2 will not turn the associated led red on failure. Do this when single power supply 1 operation is used or when the device is powered soley by…
scalarEnumeration.1.3.6.1.4.1.3181.10.6.1.31.4
cableTestConfigTable
The cable tester allows for detection of copper cable faults and can even detect where the fault is located.
table-.1.3.6.1.4.1.3181.10.6.1.31.6
ioSignalConfigTabletable-.1.3.6.1.4.1.3181.10.6.1.31.7