G6-HARDWARE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
10
Rows
10
Columns
84

cableTestConfigTable

table
.1.3.6.1.4.1.3181.10.6.1.31.6 · 1 row entry · 6 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk cableTestConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::cableTestConfigTable' 
The cable tester allows for detection of copper cable faults and can even detect where the fault is located.
cableTestConfigEntry row .1.3.6.1.4.1.3181.10.6.1.31.6.1
Indexes
Column Syntax OID
cableTestConfigPortIndex
Automatically generated
Integer32
Constraints:
range: 0-24
 .1.3.6.1.4.1.3181.10.6.1.31.6.1.1
cableTestConfigEnableAutoCableTest
When enabled a cable test is performed each time the link goes down. The test is only performed for copper ports or dual media ports in copper mode.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.3181.10.6.1.31.6.1.2
cableTestConfigEventGeneration
When the cable termination status changes an event can be raised.
Enumerationr/w
Enumerated Values:
0disabled
1anyChange
2connectionsOnly
 .1.3.6.1.4.1.3181.10.6.1.31.6.1.3
cableTestConfigReflectionThreshold
Select a value up to 508 which is used to decide between a connected cable and a remotely disconnected cable. With actively terminated data ports, the detection is difficult and precise setup is required. Please refer t…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.6.1.4
cableTestConfigReflectionHysteresis
Choose value to prevent oscillation when reflection value is slightly shifting.
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.6.1.5
cableTestConfigStartTestNow
May be used to manually start a cable test. ATTENTION: If the port is in link up status it will be forced to link down first. This will disrupt the current data traffic. Therefore, type start_test_now = CONFIRM.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.6.1.6

ioSignalConfigTable

table
.1.3.6.1.4.1.3181.10.6.1.31.7 · 1 row entry · 10 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk ioSignalConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::ioSignalConfigTable'
ioSignalConfigEntry row .1.3.6.1.4.1.3181.10.6.1.31.7.1
Indexes
Column Syntax OID
ioSignalConfigIndex
Automatically generated
Integer32
Constraints:
range: 0-0
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.1
ioSignalConfigSignalMode
Permit setting of io signal LEDs and relays to static or blink blink mode for increased visualization.
Enumerationr/w
Enumerated Values:
0static
1ledBlink
2relayBlink
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.2
ioSignalConfigInput1Mode
When this function is activated the external alarm input 1 is monitored. Note: alarm inputs are not available in all product versions.
Enumerationr/w
Enumerated Values:
0disabled
1alarmWhenHigh
2alarmWhenLow
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.3
ioSignalConfigInput1Name
A customer specific name can be specified for input 1. This name will appear in the associated event messages.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.4
ioSignalConfigInput2Mode
When this function is activated the external alarm input 2 is monitored. Note: alarm inputs are not available in all product versions.
Enumerationr/w
Enumerated Values:
0disabled
1alarmWhenHigh
2alarmWhenLow
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.5
ioSignalConfigInput2Name
A customer specific name can be specified for input 2. This name will appear in the associated event messages.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.6
ioSignalConfigOutput1Trigger
Defines on which condition the alarm relay 1 is activated. Note: alarm relays are not available in all product versions.
Enumerationr/w
Enumerated Values:
0disabled
1whileRunning
2redundancyFail
3highTemp
4off
5on
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.7
ioSignalConfigOutput1Name
A customer specific name can be specified for alarm output 1. This name will appear in the associated event messages.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.8
ioSignalConfigOutput2Trigger
Defines on which condition the alarm relay 2 is activated. Note: alarm relays are not available in all product versions.
Enumerationr/w
Enumerated Values:
0disabled
1whileRunning
2redundancyFail
3highTemp
4off
5on
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.9
ioSignalConfigOutput2Name
A customer specific name can be specified for alarm output 2. This name will appear in the associated event messages.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.7.1.10

moduleInfoTable

table
.1.3.6.1.4.1.3181.10.6.1.31.109 · 1 row entry · 8 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk moduleInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::moduleInfoTable' 
This section indicates which modules are inserted in the optional extension slots.
moduleInfoEntry row .1.3.6.1.4.1.3181.10.6.1.31.109.1
Indexes
Column Syntax OID
moduleInfoIndex
Automatically generated
Integer32
Constraints:
range: 0-3
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.1
moduleInfoUnitType
Identfies the general type of module.
Enumeration
Enumerated Values:
0notPresent
1baseUnit
2expansion
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.2
moduleInfoArticleNumber
The article number of the module in this slot.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.3
moduleInfoSerialNumber
The serial number of the module in this slot.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.4
moduleInfoHardwareVersion
This device hardware revision number.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.5
moduleInfoProjectNumber
MICROSENS project number.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.6
moduleInfoOccupiedSlots
Lists all slots contained in this module.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.7
moduleInfoDescription
Feature summary of the module.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.109.1.8

slotInfoTable

table
.1.3.6.1.4.1.3181.10.6.1.31.110 · 1 row entry · 4 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk slotInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::slotInfoTable' 
This section indicates which modules are inserted in the optional extension slots.
slotInfoEntry row .1.3.6.1.4.1.3181.10.6.1.31.110.1
Indexes
Column Syntax OID
slotInfoIndex
Automatically generated
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.3181.10.6.1.31.110.1.1
slotInfoBoardType
General type of board function
Enumeration
Enumerated Values:
0notPresent
1undefined
2power
3cpu
4port
5io
6ms10gPort
 .1.3.6.1.4.1.3181.10.6.1.31.110.1.2
slotInfoBoardId
This identifies the board type for internal operation.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3181.10.6.1.31.110.1.3
slotInfoVersionBits
Version bits from hardware or backplane.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.110.1.4

portInfoTable

table
.1.3.6.1.4.1.3181.10.6.1.31.111 · 1 row entry · 10 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk portInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::portInfoTable' 
Used to map physical to logical port ids.
portInfoEntry row .1.3.6.1.4.1.3181.10.6.1.31.111.1
Indexes
Column Syntax OID
portInfoPortIndex
Automatically generated
Integer32
Constraints:
range: 0-24
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.1
portInfoSystemSlot
Describes on which system slot this port index is located.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.2
portInfoSwitchPort
Describes on which switch port this port index is located.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.3
portInfoUserSlot
Slot number as seen by customer.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.4
portInfoUserPort
Port number as seen by customer.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.5
portInfoSnmpPort
Slot and port representation as used in SNMP. Formula is Slot*100 + Port.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.6
portInfoSnmpInstance
Port instance counting from 0 to number of ports
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.7
portInfoHardwarePort
Port number as used internally. Ports may not be in sequential order.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.8
portInfoInterfaceType
Identifies port as copper or optical. Also used for snmp ifType definition
Enumeration
Enumerated Values:
0copper
1optical
2dualMedia
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.9
portInfoProperties
Describes which functions the port can support.
Bits
Enumerated Values:
0internal
1ms10Mb
2ms100Mb
3ms1000Mb
4rj45
5sfp
6ms1x9
7poe
8poePlus
9pd
10dualMedia
11linkPort
12csfp
 .1.3.6.1.4.1.3181.10.6.1.31.111.1.10

portLedsTable

table
.1.3.6.1.4.1.3181.10.6.1.31.112 · 1 row entry · 5 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk portLedsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::portLedsTable' 
This section indicates the state of all port related LEDs.
portLedsEntry row .1.3.6.1.4.1.3181.10.6.1.31.112.1
Indexes
Column Syntax OID
portLedsPortIndex
Automatically generated
Integer32
Constraints:
range: 0-31
 .1.3.6.1.4.1.3181.10.6.1.31.112.1.1
portLedsEthernetColor
Ethernet Link LED.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.112.1.2
portLedsEthernetBlinking
Ethernet Link LED.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.112.1.3
portLedsPoeColor
Power over Ethernet LED. For optical ports this indicates signal detect status.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.112.1.4
portLedsPoeBlinking
Power over Ethernet LED. For optical ports this indicates signal detect status.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.112.1.5

deviceLedsTable

table
.1.3.6.1.4.1.3181.10.6.1.31.113 · 1 row entry · 21 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk deviceLedsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::deviceLedsTable' 
This section indicates the state of all LEDs which are not port related. Please note: Not every unit offers all LEDs.
deviceLedsEntry row .1.3.6.1.4.1.3181.10.6.1.31.113.1
Indexes
Column Syntax OID
deviceLedsIndex
Automatically generated
Integer32
Constraints:
range: 0-0
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.1
deviceLedsSystem1Color
This status corresponds to 'sys' LED on some devices.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.2
deviceLedsSystem1Blinking
This status corresponds to 'sys' LED on some devices.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.3
deviceLedsSystem2Color
Displays external management activity.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.4
deviceLedsSystem2Blinking
Displays external management activity.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.5
deviceLedsPowerOn1Color
This status corresponds to 'on' LED on some devices.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.6
deviceLedsPowerOn1Blinking
This status corresponds to 'on' LED on some devices.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.7
deviceLedsPowerOn2Color
Alternative power input LED.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.8
deviceLedsPowerOn2Blinking
Alternative power input LED.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.9
deviceLedsRing1Color
This LED is used when ring protection is enabled.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.10
deviceLedsRing1Blinking
This LED is used when ring protection is enabled.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.11
deviceLedsRing2Color
This LED is used when ring protection is enabled.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.12
deviceLedsRing2Blinking
This LED is used when ring protection is enabled.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.13
deviceLedsSignalIn1Color
Indicates status of alarm input 1.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.14
deviceLedsSignalIn1Blinking
Indicates status of alarm input 1.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.15
deviceLedsSignalIn2Color
Indicates status of alarm input 2.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.16
deviceLedsSignalIn2Blinking
Indicates status of alarm input 2.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.17
deviceLedsSignalOut1Color
Indicates status of alarm relay output 1.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.18
deviceLedsSignalOut1Blinking
Indicates status of alarm relay output 1.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.19
deviceLedsSignalOut2Color
Indicates status of alarm relay output 2.
Enumeration
Enumerated Values:
0off
1blue
2green
3red
4orange
5cyan
6magenta
7white
8noLed
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.20
deviceLedsSignalOut2Blinking
Indicates status of alarm relay output 2.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.113.1.21

cableTestStatusTable

table
.1.3.6.1.4.1.3181.10.6.1.31.114 · 1 row entry · 12 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk cableTestStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::cableTestStatusTable' 
This table display the result of the last cable test. Values are only available for copper ports while a link is down and if  the cable test function is enabled.
cableTestStatusEntry row .1.3.6.1.4.1.3181.10.6.1.31.114.1
Indexes
Column Syntax OID
cableTestStatusPortIndex
Automatically generated
Integer32
Constraints:
range: 0-24
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.1
cableTestStatusUpdateTimeStamp
Indicates the time when this record was last updated.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.2
cableTestStatusPair0State
Indicates line termination test results for wire pair 0 (Pins 1/2)
Enumeration
Enumerated Values:
0notAvailable
1pairOk
2pairOpen
3samePairShort
4crossPairShort
5terminationLow
6terminationHigh
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.3
cableTestStatusPair0DistanceToFault
Distance to fault on wire pair 0 in centimeters. Indicates 0 when no fault is detected or the function is unused.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.4
cableTestStatusPair1State
Indicates line termination test results for wire pair 1 (Pins 3/6)
Enumeration
Enumerated Values:
0notAvailable
1pairOk
2pairOpen
3samePairShort
4crossPairShort
5terminationLow
6terminationHigh
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.5
cableTestStatusPair1DistanceToFault
Distance to fault on wire pair 1 in centimeters. Indicates 0 when no fault is detected or the function is unused.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.6
cableTestStatusPair2State
Indicates line termination test results for wire pair 2 (Pins 4/5)
Enumeration
Enumerated Values:
0notAvailable
1pairOk
2pairOpen
3samePairShort
4crossPairShort
5terminationLow
6terminationHigh
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.7
cableTestStatusPair2DistanceToFault
Distance to fault on wire pair 2 in centimeters. Indicates 0 when no fault is detected or the function is unused.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.8
cableTestStatusPair3State
Indicates line termination test results for wire pair 3 (Pins 7/8)
Enumeration
Enumerated Values:
0notAvailable
1pairOk
2pairOpen
3samePairShort
4crossPairShort
5terminationLow
6terminationHigh
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.9
cableTestStatusPair3DistanceToFault
Distance to fault on wire pair 3 in centimeters. Indicates 0 when no fault is detected or the function is unused.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.10
cableTestStatusReflectionValue
A unitless value that indicates a measure of reflection level. For difficult to detect actively terminated devices perform a measurement with remotely plugged-in and then unplugged cable. Note the reflection values an c…
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.11
cableTestStatusCableStatus
Indicates the concluded status summary.
Enumeration
Enumerated Values:
0notAvailable
1noCable
2pluggedInLocally
3pluggedInRemotely
4terminatedCable
5terminationTooLow
6defective
 .1.3.6.1.4.1.3181.10.6.1.31.114.1.12

ioSignalStatusTable

table
.1.3.6.1.4.1.3181.10.6.1.31.115 · 1 row entry · 5 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk ioSignalStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::ioSignalStatusTable' 
This section is only used for devices which offer external signal inputs and outputs.
ioSignalStatusEntry row .1.3.6.1.4.1.3181.10.6.1.31.115.1
Indexes
Column Syntax OID
ioSignalStatusIndex
Automatically generated
Integer32
Constraints:
range: 0-0
 .1.3.6.1.4.1.3181.10.6.1.31.115.1.1
ioSignalStatusInput1AlarmActive
Indicates true when the input 1 is logically active.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.115.1.2
ioSignalStatusInput2AlarmActive
Indicates true when the input 2 is logically active.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.115.1.3
ioSignalStatusOutput1RelayActive
Indicates true when the output 1 relay is activated.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.115.1.4
ioSignalStatusOutput2RelayActive
Indicates true when the output 2 relay is activated.
Enumeration
Enumerated Values:
0false
1true
 .1.3.6.1.4.1.3181.10.6.1.31.115.1.5

tcamStatusTable

table
.1.3.6.1.4.1.3181.10.6.1.31.116 · 1 row entry · 3 columns
Open in standard view
Uses the microsens variant from /opt/observium/mibs/microsens.
Command help
Walk tcamStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'G6-HARDWARE-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'G6-HARDWARE-MIB::tcamStatusTable' 
The TCAM is a programmable wire speed packet filter. The filter is controlled by the system automatically. This table indicates which filters have been set.
tcamStatusEntry row .1.3.6.1.4.1.3181.10.6.1.31.116.1
Indexes
Column Syntax OID
tcamStatusIndex
Automatically generated
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.3181.10.6.1.31.116.1.1
tcamStatusControlFile
Reflects the name of the control file associated with this tcam entry.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.116.1.2
tcamStatusDescription
Descriptive text what explains what this tcam entry will do.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3181.10.6.1.31.116.1.3