eltexVpcDomainSystemMac

ELTEX-VPC-MIB · .1.3.6.1.4.1.35265.125.1.1.2.1.6
MIB view Table view

Object

column r/w SNMPv2-TCMacAddress 
To configure the MAC address for the VPC domain. This mac-address 
is used in the LACP PDUs and STP BPDUs 
that are sent out on VPC member ports. For the VPC domain to use 
the manually configured VPC MAC address, it should be manually 
configured on both the VPC peers and should be the same. If VPC 
is configured on only one of the VPC peers or is configured 
different on VPC peers, auto-generated MAC address is used. 
The specified MAC address should be a unicast MAC address in 
<aa:bb:cc:dd:ee:ff> format and should not be equal to the 
MAC address of either primary VPC or secondary VPC device.  
The manually configured VPC MAC address is used instead of 
auto-generated VPC MAC address only if the VPC feature is 
re-enabled after configuring the VPC MAC address.

Context

MIB
ELTEX-VPC-MIB
OID
.1.3.6.1.4.1.35265.125.1.1.2.1.6
Type
column
Access
readwrite
Status
current
Parent
eltexVpcDomainConfigEntry
Table
eltexVpcDomainConfigTable
Siblings
13

Syntax

SNMPv2-TCMacAddress
Source
SNMPv2-TCMacAddress
Base type
OctetString

Values & Constraints

Type Constraints
range: 6

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
eltexVpcDomainIndex
VPC Domain ID.
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.1
eltexVpcDomainPeerDetectionTimeout
To configure the peer detection protocol reception timeout. Configurable range is 700 to 14000 mseconds.
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.10
eltexVpcDomainPeerIpAddr
To configure IP address of the peer VPC switch. This configuration is used by the dual control plane detection protocol on the VPC switches. NOTE: In order to set v…
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.35265.125.1.1.2.1.11
eltexVpcDomainSourceIpAddr
To configure Self IP address of the VPC switch that is used as the source IP by the dual control plane detection protocol on the VPC switches. NOTE: In order to se…
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.35265.125.1.1.2.1.12
eltexVpcDomainDcpdpUdpPort
To configure the UDP port on which the VPC switch listens to the peer detection protocol messages.
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.13
eltexVpcDomainStatus
Status of VPC Domain.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.35265.125.1.1.2.1.14
eltexVpcDomainPeerLink
To configures a port channel as the VPC peer link. The configurable range is a valid port channel interface index.
columnIF-MIBInterfaceIndexOrZero.1.3.6.1.4.1.35265.125.1.1.2.1.2
eltexVpcDomainKeepalivePriority
To configure the priority of the VPC switch. This value is used for the VPC role election. Note: The VPC switch with lower priority becomes the Primary. If both the VPC peer…
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.3
eltexVpcDomainKeepaliveTimeout
To configure the peer keepalive timeout value (in seconds). If an VPC switch does not receive keepalive messages from the peer for this timeout value, it takes the decision to tra…
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.4
eltexVpcDomainKeepaliveMode
To start/stop the keepalive state machine on the VPC device, if VPC is globally enabled.
columnEnumeration.1.3.6.1.4.1.35265.125.1.1.2.1.5
eltexVpcDomainSystemPriority
To configure the system priority for the VPC domain. This is used in the STP BPDU sent out on VPC member ports. System-priority should be configured same on both the VPC peers. …
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.7
eltexVpcDomainPeerDetectionMode
To start/stop the dual control peer detection protocol on the VPC switch. The following options are supported: Note: The peer VPC switch's IP address has to be conf…
columnEnumeration.1.3.6.1.4.1.35265.125.1.1.2.1.8
eltexVpcDomainPeerDetectionInterval
To configure the peer detection protocol transmission interval. Configurable range is 200 to 4000 mseconds.
columnUnsigned32.1.3.6.1.4.1.35265.125.1.1.2.1.9