serialDteCharSize
DS8200v2-MIB ·
.1.3.6.1.4.1.321.100.2.5.1.1.27
Object
column
r/w
Enumeration
Specifies the number of bits per character. This variable is valid in ASYNC mode.
Context
- MIB
- DS8200v2-MIB
- OID
.1.3.6.1.4.1.321.100.2.5.1.1.27- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- serialDteConfigTableEntry
- Table
- serialDteConfigTable
- Siblings
- 29
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | other |
2 | five |
3 | six |
4 | seven |
5 | eight |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| serialDteConfigNearIndex Selects the near device. | column | Integer32 | .1.3.6.1.4.1.321.100.2.5.1.1.1 |
| serialDteStopBit This variable describes the stop bit setting for the
DTE interface. This variable is only valid when the
DTE interface is set to ASYNC. The values mean:
serialDteStopBit1
The DTE … | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.10 |
| serialDteMode This variable describes mode in which data is
being sent from the DDS unit back towards the network. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.11 |
| serialDteDSR Selects DSR behavior. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.12 |
| serialDteDCD Selects DCD behavior. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.13 |
| serialDteRTS Selects RTS behavior. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.14 |
| serialDteRTSDelay Selects RTS to CTS transition delay. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.15 |
| serialDteDTR Reports if DTR from the DTE device is false. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.16 |
| serialDteCTS Specifies the control of the CTS signal at the port. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.17 |
| serialDteV54 Specifies if the unit should respond to inband V.54 loop commands. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.18 |
| serialDteLL Specifies if the unit should respond to local loop activation by the local loopback signal (EIA530 or RS-232 pin 18). | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.19 |
| serialDteConfigFarIndex Selects the far device. | column | Integer32 | .1.3.6.1.4.1.321.100.2.5.1.1.2 |
| serialDteRL Specifies if the unit should respond to remote loop activation by the remote loopback signal (EIA530 or RS-232 pin 21). | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.20 |
| serialDteStartChannel Specifies the starting channel for the interface. | column | Integer32 | .1.3.6.1.4.1.321.100.2.5.1.1.21 |
| serialDteNumberOfChannels Specifies the number of channels allocated to the interface. | column | Integer32 | .1.3.6.1.4.1.321.100.2.5.1.1.22 |
| serialDteTxClock Specifies how the interface derives its transmit clock. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.23 |
| serialDteBundle Specifies the allocation pattern of channels assigned
to the serial port. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.24 |
| serialDteChannelRate Specifies the rate of all channels assigned to the serial port. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.25 |
| serialDteInvertClock Specifies if an inverted clock is used to send data from the serial port. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.26 |
| serialDteFlowControl Specifies the Flow control to use. This variable is
valid only in ASYNC mode. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.28 |
| serialDtePinStatus This object provides a summary of the Serial port pin status. | column | OctetString | .1.3.6.1.4.1.321.100.2.5.1.1.29 |
| serialDteConfigIndex Index into the DteTable. | column | Integer32 | .1.3.6.1.4.1.321.100.2.5.1.1.3 |
| serialDteInInvertClock Specifies to use the inverted clock edge for data clocked into the serial port. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.30 |
| serialDteDescription Contains a textual description of the port. | column | OctetString | .1.3.6.1.4.1.321.100.2.5.1.1.4 |
| serialDteType Selects the DTE port type if applicable. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.5 |
| serialDteRate Selects the DTE port bit. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.6 |
| serialDteInvertData Specifies whether transmit and receive are inverted at the port. | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.7 |
| serialDteFormat This variable describes the current operations format
of the DTE interface. The values mean:
serialDteFormatSync
The DTE interface is currently set to operate
in Synchronous clock… | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.8 |
| serialDteParity This variable describes the current parity selected
for the DTE interface. This variable is only valid
when the DTE Mode is set to ASYNC. The values mean:
serialDteParityNone
The … | column | Enumeration | .1.3.6.1.4.1.321.100.2.5.1.1.9 |