netAPSConfigStatusBitmap
DS8200v2-MIB ·
.1.3.6.1.4.1.321.100.2.14.1.1.15
Object
column
Integer32
TR54017 defined bitmap status for this line interface:
Value is 1 if this line is carrying service.
Value is 2 if this line is in a failed state.
Value is 4 if this line is in an inhibit state.
Value is 8 if this line is looped back.
Value is 16 if the other line is in a failed state.
Value is 32 if the other line is in an inhibit state.
Value is 64 if the other line is looped back.
Value is 128 if the manual inhibit is active
Note that multiple status conditions may exist at the same time.
The failed state is determined when carrier fails, or the ES threshold is reached, or the consecutive SES threshold is reached.
The inhibit state is set when the manual inhibit setting affects this line or the line is inhibited by the remote end.
Context
- MIB
- DS8200v2-MIB
- OID
.1.3.6.1.4.1.321.100.2.14.1.1.15- Type
- column
- Access
- readonly
- Status
- current
- Parent
- netAPSConfigTableEntry
- Table
- netAPSConfigTable
- Siblings
- 19
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| netAPSConfigNearIndex Selects the near device. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.1 |
| netAPSConfigESCount This parameter is the number of erred seconds in the current 15-minute interval.
This count is reset at the beginning of a new 15-minute interval. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.10 |
| netAPSConfigESSwitchEvent This status indicates if exceeding the ES threshold caused a transfer to the other line. | column | Enumeration | .1.3.6.1.4.1.321.100.2.14.1.1.11 |
| netAPSConfigCSESThreshold This parameter is the number of consecutive SES needed before a transfer request is triggered.
A setting of zero disables this trigger. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.12 |
| netAPSConfigCSESCount This parameter is the number of consecutive SES detected.
This count stops when 900 is reached and is reset when a non-SES is detected. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.13 |
| netAPSConfigCSESSwitchEvent This status indicates if exceeding the consecutive SES threshold caused a transfer to the other line. | column | Enumeration | .1.3.6.1.4.1.321.100.2.14.1.1.14 |
| netAPSConfigStatusString ASCII string version of netAPSConfigStatusBitmap for this line status bits | column | OctetString | .1.3.6.1.4.1.321.100.2.14.1.1.16 |
| netAPSConfigTimeInInterval The number of seconds into the netAPSHist24Table current interval. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.17 |
| netAPSConfigValidIntervals The number of valid intervals in the netAPSHist24Table | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.18 |
| netAPSConfigValidDays The number of valid days in the netAPSHist30Table | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.19 |
| netAPSConfigFarIndex Selects the far device. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.2 |
| netAPSConfigReset This action parameter does the following when the given value is set:
other - Does nothing
clearAlarms - Clear the APS events and counts
clearHistory - Clear the APS history table… | column | Enumeration | .1.3.6.1.4.1.321.100.2.14.1.1.20 |
| netAPSConfigifIndex Selects the MIB-II ifIndex. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.3 |
| netAPSConfigOtherifIndex MIB-II ifIndex of the other interface involved with the APS. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.4 |
| netAPSConfigMode tr54017 - Implements TR54017
autoABswitch - Implements a single ended A/B switch between two independent lines
masterAltCarrier - Master side of alternate carrier APS
slaveAltCarr… | column | Enumeration | .1.3.6.1.4.1.321.100.2.14.1.1.5 |
| netAPSConfigRevert disabled - Service does not return to the primary line until the backup line fails.
enabled - Service automatically returns to the primary line when the primary line is able to ca… | column | Enumeration | .1.3.6.1.4.1.321.100.2.14.1.1.6 |
| netAPSConfigManualInhibit Disabled - Neither line is manually inhibited from carrying service.
ThisLine - This line is manually inhibited from carrying service.
OtherLine - The other line is manually inhib… | column | Enumeration | .1.3.6.1.4.1.321.100.2.14.1.1.7 |
| netAPSConfigAvailabilityTimer The line availability timer represents the minimum amount of time that is free of errors in active events that must expire before this line is returned to service availability.
Th… | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.8 |
| netAPSConfigESThreshold This parameter is the number of erred seconds in a 15-minute period needed before a transfer request is triggered.
A setting of zero disables this trigger. | column | Integer32 | .1.3.6.1.4.1.321.100.2.14.1.1.9 |