dsx1Fdl

DS1-MIB · .1.3.6.1.2.1.10.18.6.1.13
Commands MIB view Table view

Object

column r/w Integer32 
This bitmap describes the use of the
facilities data link and is the sum of the
capabilities.  Set any bits that are appropriate:
              
other(1),
dsx1AnsiT1403(2),
dsx1Att54016(4),
dsx1FdlNone(8)
              
 'other' indicates that a protocol other than
one of the following is used.
              
 'dsx1AnsiT1403' refers to the FDL exchange
recommended by ANSI.
              
 'dsx1Att54016' refers to ESF FDL exchanges.
              
 'dsx1FdlNone' indicates that the device does
not use the FDL.

Context

MIB
DS1-MIB
OID
.1.3.6.1.2.1.10.18.6.1.13
Type
column
Access
readwrite
Status
current
Parent
dsx1ConfigEntry
Groups
3

Net-SNMP examples

How SNMP and these commands work

Walk the column to discover its indexed instances, or supply every index to read one instance.

Walk the column
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DS1-MIB' -M '/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DS1-MIB::dsx1Fdl'
More examples
Read one indexed instance
/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'DS1-MIB' -M '/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DS1-MIB::dsx1Fdl.<dsx1LineIndex>'
Translate to a numeric OID
/usr/bin/snmptranslate -Pud -Ir -On -m 'DS1-MIB' -M '/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'DS1-MIB::dsx1Fdl'

Syntax

Integer32

Values & Constraints

Object Constraints
range: 1-15

Conformance

Member of
ds1NearEndCfgGroup ds1NearEndConfigGroup ds1NearEndConfigurationGroup
Compliance refinements
ds1Compliance readonly
The ability to set the FDL is not required.
ds1J1Compliance readonly
The ability to set the FDL is not required.
ds1MibE1PriCompliance readonly
Facilities Data Link usage on E1 ISDN
Primary Rate interfaces.
Note: There is an 'M-Channel' in E1,
using National Bit Sa4 (G.704,
Table 5A). It is used to implement
management features between ET
and NT. This is different from
FDL in T1, which is used to carry
control signals and performance
data. In E1, control and status
signals are carried using National
Bits Sa5, Sa6, and A (RAI Ind.).
This indicates that only the other(1) or
eventually the dsx1Fdl-none(8) bits should
be set in this object for E1 PRI.
ds1MibE1PriNCompliance readonly
Facilities Data Link usage on E1 ISDN
Primary Rate interfaces.
Note: There is an 'M-Channel' in E1,
using National Bit Sa4 (G704,
Table 5A). It is used to implement

management features between ET
and NT. This is different from
FDL in T1, which is used to carry
control signals and performance
data. In E1, control and status
signals are carried using National
Bits Sa5, Sa6, and A (RAI Ind.).
This indicates that only the other(1) or
eventually the dsx1Fdl-none(8) bits should
be set in this object for E1 PRI.
ds1MibT1PriCompliance readonly
Facilities Data Link usage on T1 ISDN
Primary Rate interfaces.
Note: Eventually, dsx1Att-54016(4) is to be
used here since the line type is ESF.
ds1MibT1PriNCompliance readonly
Facilities Data Link usage on T1 ISDN
Primary Rate interfaces.
Note: Eventually, dsx1Att-54016(4) is to be
used here since the line type is ESF.
ds1NCompliance readonly
The ability to set the FDL is not required.
ds1NMibE1PriNCompliance readonly
Facilities Data Link usage on E1 ISDN
Primary Rate interfaces.
Note: There is an 'M-Channel' in E1,
using National Bit Sa4 (G704,
Table 5A). It is used to implement
management features between ET
and NT. This is different from
FDL in T1, which is used to carry
control signals and performance
data. In E1, control and status
signals are carried using National
Bits Sa5, Sa6, and A (RAI Ind.).
This indicates that only the other(1) or
eventually the dsx1Fdl-none(8) bits should
be set in this object for E1 PRI.
ds1NMibT1PriNCompliance readonly
Facilities Data Link usage on T1 ISDN
Primary Rate interfaces.
Note: Eventually, dsx1Att-54016(4) is to be
used here since the line type is ESF.