dsx1Channelization

DS1-MIB · .1.3.6.1.2.1.10.18.6.1.20

Object

column r/w Enumeration

Indicates whether this DS1/E1 or DS2 is
channelized or unchannelized.
              
The value of enabledDs0(2) indicates that this is a
DS1 channelized into DS0s.  Setting this value will
cause the creation, and resetting it to disabled(1)
will cause the deletion of entries in the ifTable
for the DS0s that are within the DS1.
              
The value of enabledDs1(3) indicates that this is a
DS2 channelized into DS1s.  Setting this value will
cause the creation, and resetting it to disabled(1)
will cause the deletion of entries in the ifTable
for the DS1s that are within the DS2.

Context

MIB: DS1-MIB
OID: .1.3.6.1.2.1.10.18.6.1.20
Type: column
Access: readwrite
Status: current
Parent: dsx1ConfigEntry
Table: dsx1ConfigTable
Siblings: 22

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	disabled
`2`	enabledDs0
`3`	enabledDs1

Related Objects

Sibling Objects

Object	Type	Syntax	OID
dsx1LineIndex This object should be made equal to ifIndex. The next paragraph describes its previous usage. Making the object equal to ifIndex allows proper use of the ifStackTable and ds0/ds0…	column	IF-MIBInterfaceIndex	`.1.3.6.1.2.1.10.18.6.1.1`
dsx1LineStatus This variable indicates the line status of the interface. It contains loopback, failure, received alarm and transmitted alarms information. The dsx1LineStatus is a…	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.10`
dsx1SignalMode 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that DS1 Robbed Bit Signaling is in use. 'bitOriented…	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.11`
dsx1TransmitClockSource The source of transmit clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a l…	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.12`
dsx1Fdl This bitmap describes the use of the facilities data link and is the sum of the capabilities. Set any bits that are appropriate: other(1), dsx1AnsiT1403(2), dsx1At…	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.13`
dsx1InvalidIntervals The number of intervals in the range from 0 to dsx1ValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some interv…	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.14`
dsx1LineLength The length of the DS1 line in meters. This object provides information for line build-out circuitry. This object is only useful if the interface has configurable line build-out …	column	meters Integer32	`.1.3.6.1.2.1.10.18.6.1.15`
dsx1LineStatusLastChange The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was entered prior to the last re-initialization of the pro…	column	SNMPv2-TCTimeStamp	`.1.3.6.1.2.1.10.18.6.1.16`
dsx1LineStatusChangeTrapEnable Indicates whether dsx1LineStatusChange traps should be generated for this interface.	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.17`
dsx1LoopbackStatus This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks established by a manager and remotely from the far end. …	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.18`
dsx1Ds1ChannelNumber This variable represents the channel number of the DS1/E1 on its parent DS2/E2 or DS3/E3. A value of 0 indicates that this DS1/E1 does not have a parent DS3/E3.	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.19`
dsx1IfIndex deprecated This value for this object is equal to the value of ifIndex from the Interfaces table (RFC 2863).	column	IF-MIBInterfaceIndex	`.1.3.6.1.2.1.10.18.6.1.2`
dsx1LineMode This setting puts the T1 framer into either long-haul (CSU) mode or short-haul (DSU) mode.	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.21`
dsx1LineBuildOut Attenuation setting for T1 framer in long haul (CSU) mode. The optional values are -7.5dB, -15dB, -22.5dB, and 0dB.	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.22`
dsx1LineImpedance Nominal line impedance. For T1 and J1 lines, the value is typically balanced100ohms(3). For E1 lines, the value is typically unbalanced75ohms(2) and balanced120ohms(4). When th…	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.23`
dsx1TimeElapsed The number of seconds that have elapsed since the beginning of the near-end current error- measurement period. If, for some reason, such as an adjustment in the system's time-of-…	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.3`
dsx1ValidIntervals The number of previous near-end intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the v…	column	Integer32	`.1.3.6.1.2.1.10.18.6.1.4`
dsx1LineType This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as wel…	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.5`
dsx1LineCoding This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. dsx1JBZS refers the Jamm…	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.6`
dsx1SendCode This variable indicates what type of code is being sent across the DS1 interface by the device. Setting this variable causes the interface to send the code requested. The values …	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.7`
dsx1CircuitIdentifier This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.	column	OctetString	`.1.3.6.1.2.1.10.18.6.1.8`
dsx1LoopbackConfig This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should return inconsistentValue in response to a requested l…	column	Enumeration	`.1.3.6.1.2.1.10.18.6.1.9`