aniDevFilterIdentifier
DEVFILTER-MIB ·
.1.3.6.1.4.1.4325.2.8.1.1.2
Object
column
r/w
Integer32
A unique number which identifies the filtering rule.
Context
- MIB
- DEVFILTER-MIB
- OID
.1.3.6.1.4.1.4325.2.8.1.1.2- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- aniDevFilterEntry
- Table
- aniDevFilterTable
- Siblings
- 31
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| aniDevFilterIfIndex The Interface Type.
On SU, only ethernet(1) and wireless-port1(2) are valid.
On BSU, ethernet(1) and all configured wireless interfaces
-- wireless-port1(2), wire… | column | Enumeration | .1.3.6.1.4.1.4325.2.8.1.1.1 |
| aniDevFilterIpDaddr The destination IP address for this Filter.
IP Destination Address and Subnet Mask go in a pair.
So if aniDevFilterIpDaddr is configured, then
aniDevFilterIpDmask should be confi… | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.4325.2.8.1.1.10 |
| aniDevFilterIpDmask The Subnet mask for the destination IP Address.
IP Destination Address and Subnet Mask go in a pair.
So if aniDevFilterIpDaddr is configured, then
aniDevFilterIpDmask should be c… | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.4325.2.8.1.1.11 |
| aniDevFilterIpSourceStart The lowest bound value for the source port number.
List of Some Well Known Ports:
Application Port
----------- ----
Ftp Data 20
Ftp Control 2… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.12 |
| aniDevFilterIpSourceEnd The highest bound value for the source port number.
Refer to the Well known ports list under
aniIpFilterIpSourceStart description.
In addition to the list, the use… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.13 |
| aniDevFilterIpDestStart The lowest bound value for the destination port number.
Refer to the Well known ports list under
aniIpFilterIpSourceStart description.
In addition to the list, the… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.14 |
| aniDevFilterIpDestEnd The highest bound value for the destination port number.
Refer to the Well known ports list under
aniIpFilterIpSourceStart description.
In addition to the list, th… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.15 |
| aniDevFilterIpOptions The Mask value for the IP Options.
No Operation (0x000001)
Route Record (0x000002)
Time Stamp (0x000040)
MTU Probe (0x000008)
MTU Reply (0x000010)
Trace Route (0x000080)
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4325.2.8.1.1.16 |
| aniDevFilterIpSecOptions The IP Security Value. | column | Enumeration | .1.3.6.1.4.1.4325.2.8.1.1.17 |
| aniDevFilterIcmpMsgType The Message Type for ICMP Protocol.
This field is valid only if the aniDevFilterIpProtocol
is set to ICMP or not specified by the user.
Valid Range:… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4325.2.8.1.1.18 |
| aniDevFilterIcmpSubcode The Subcode for ICMP Protocol.
This field is valid only if the aniDevFilterIpProtocol is
set to ICMP or not specified by the user.
If this field is specified then… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4325.2.8.1.1.19 |
| aniDevFilterTcpFlags The TCP Flags.
The valid range:
Urgent (0x20)
Acknowledgement (0x10)
Push (0x08)
Reset (0x04)
Sync (0x02)
Sync-Ack (0x12)
Finish (0x01)
Finish-Ack (0x11)
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4325.2.8.1.1.20 |
| aniDevFilterDestMacMask The MAC address and mask value for destination. | column | OctetString | .1.3.6.1.4.1.4325.2.8.1.1.21 |
| aniDevFilterSourceMac The MAC Address of the source. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.4325.2.8.1.1.22 |
| aniDevFilterEnetType The Ethernet type value in the ethernet header.
The maximum length of the ethernet packet is 1500 (0x5DC).
The value of the ethernet type must be greater than 1500.… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4325.2.8.1.1.23 |
| aniDevFilterLlcDSAP The DSAP (Destination Service Access Point) value
in LLC Header.
Valid Range: 0 to 0xFF
Applicable for IEEE 802.3 Frame Format only. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4325.2.8.1.1.24 |
| aniDevFilterLlcSSAP The SSAP (Source Service Access Point) value
in LLC Header.
Valid Range: 0 to 0xFF
Applicable for IEEE 802.3 Frame Format only. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4325.2.8.1.1.25 |
| aniDevFilterLlcControl The Control Byte of the LLC Header.
Valid Range: 0 to 0xFF
Applicable for IEEE 802.3 Frame Format only. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4325.2.8.1.1.26 |
| aniDevFilterLocalCode The Local Code for SNAP ethernet type.
Applicable for IEEE 802.3 Frame Format only.
DSAP should be set to 0xAA, SSAP should be set to 0xAA,
Control Byte should be set to 0x03.
… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4325.2.8.1.1.27 |
| aniDevFilterRowStatus This represents the state of an entry within the
table. It is used to manage creation and deletion of rows.
The values include:
active(1)
notInService(2)
notReady(3)
createAndGo… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.4325.2.8.1.1.28 |
| aniDevFilterUserPriorityHi The high priority byte of the user priority.
The user priority specifies the matching
parameters for the IEEE 802.1P user_priority
bits. An Ethernet packet with IE… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.29 |
| aniDevFilterName A name which identifies the filtering rule. | column | OctetString | .1.3.6.1.4.1.4325.2.8.1.1.3 |
| aniDevFilterUserPriorityLo The low priority byte of the user priority.
The user priority specifies the matching
parameters for the IEEE 802.1P user_priority
bits. An Ethernet packet with IEE… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.30 |
| aniDevFilterVlanIdStart The lower limit for the VLAN ID.
This value is used to specify the lower limit in the
range. Any IEEE 802.1P packet from a customer's VLAN
that falls into the range matches the r… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.31 |
| aniDevFilterVlanIdEnd The upper limit for the VLAN ID.
This value is used to specify the upper limit in the
range. Any IEEE 802.1P packet from a customer's VLAN
that falls into the range matches the r… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.32 |
| aniDevFilterPriority The priority for the filtering rule. It should be unique.
A higher number means higher priority. | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.4 |
| aniDevFilterActivationState The state of the filtering rule. | column | Enumeration | .1.3.6.1.4.1.4325.2.8.1.1.5 |
| aniDevFilterPermission The permissions for the filtering rule. | column | Enumeration | .1.3.6.1.4.1.4325.2.8.1.1.6 |
| aniDevFilterIpProtocol The IP protocol value.
List of well known IP Protocols:
Protocol Value
-------- -----
ICMP 1
IGMP 2
TCP 6
EGP 8
UDP 17
IPIP 94
RSVP 4… | column | Integer32 | .1.3.6.1.4.1.4325.2.8.1.1.7 |
| aniDevFilterIpSaddr The source IP address for this Filter.
IP Source Address and Subnet Mask go in a pair.
So if aniDevFilterIpSaddr is configured, then
aniDevFilterIpSmask should be configured as w… | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.4325.2.8.1.1.8 |
| aniDevFilterIpSmask The Subnet mask for the source IP Address.
IP Source Address and Subnet Mask go in a pair.
So if aniDevFilterIpSaddr is configured, then
aniDevFilterIpSmask should be configured … | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.4325.2.8.1.1.9 |