DEVFILTER-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
2
Rows
2
Columns
34
.1.3.6.1.4.1.4325.2.8.1 · 1 row entry · 32 columns
Uses the aperto variant from /opt/observium/mibs/aperto.
Command help
Walk aniDevFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DEVFILTER-MIB' -M '/opt/observium/mibs/aperto:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DEVFILTER-MIB::aniDevFilterTable'
This table allows the user to view the configured IP 
Filters.
aniDevFilterEntry row .1.3.6.1.4.1.4325.2.8.1.1
An entry containing objects for each IP Filter
configured.
Column Syntax OID
aniDevFilterIfIndexThe Interface Type.
On SU, only ethernet(1) and wireless-port1(2) are valid.

On BSU, ethernet(1) and all configured wireless interfaces
-- wireless-port1(2), wireless-port2(3), wireless-port3(4),
wirel…
Enumerationr/w
Enumerated Values:
1ethernet
2wireless-port1
3wireless-port2
4wireless-port3
5wireless-port4
6wireless-port5
7wireless-port6
.1.3.6.1.4.1.4325.2.8.1.1.1
aniDevFilterIdentifierA unique number which identifies the filtering rule.Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.4325.2.8.1.1.2
aniDevFilterNameA name which identifies the filtering rule.OctetStringr/w
Constraints:
range: 0-31
.1.3.6.1.4.1.4325.2.8.1.1.3
aniDevFilterPriorityThe priority for the filtering rule. It should be unique.
A higher number means higher priority.
Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.4325.2.8.1.1.4
aniDevFilterActivationStateThe state of the filtering rule.Enumerationr/w
Enumerated Values:
1inactive
2active
.1.3.6.1.4.1.4325.2.8.1.1.5
aniDevFilterPermissionThe permissions for the filtering rule.Enumerationr/w
Enumerated Values:
1block
2pass
.1.3.6.1.4.1.4325.2.8.1.1.6
aniDevFilterIpProtocolThe IP protocol value.

List of well known IP Protocols:

Protocol Value
-------- -----
ICMP 1
IGMP 2
TCP 6
EGP 8
UDP 17
IPIP 94
RSVP 46
GRE 47
TCP or UDP 257
…
Integer32r/w
Constraints:
range: 0-257
.1.3.6.1.4.1.4325.2.8.1.1.7
aniDevFilterIpSaddrThe source IP address for this Filter.
IP Source Address and Subnet Mask go in a pair.
So if aniDevFilterIpSaddr is configured, then
aniDevFilterIpSmask should be configured as well and
vice versa.
RFC1155-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.4325.2.8.1.1.8
aniDevFilterIpSmaskThe Subnet mask for the source IP Address.
IP Source Address and Subnet Mask go in a pair.
So if aniDevFilterIpSaddr is configured, then
aniDevFilterIpSmask should be configured as well and
vice versa.
RFC1155-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.4325.2.8.1.1.9
aniDevFilterIpDaddrThe destination IP address for this Filter.
IP Destination Address and Subnet Mask go in a pair.
So if aniDevFilterIpDaddr is configured, then
aniDevFilterIpDmask should be configured as well and
vice versa.
RFC1155-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.4325.2.8.1.1.10
aniDevFilterIpDmaskThe Subnet mask for the destination IP Address.
IP Destination Address and Subnet Mask go in a pair.
So if aniDevFilterIpDaddr is configured, then
aniDevFilterIpDmask should be configured as well and
vice versa.
RFC1155-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.4325.2.8.1.1.11
aniDevFilterIpSourceStartThe lowest bound value for the source port number.

List of Some Well Known Ports:

Application Port
----------- ----
Ftp Data 20
Ftp Control 21
HTTP 80
IMAP2 143
SNMP 161
P…
Integer32r/w
Constraints:
range: 0-65535
.1.3.6.1.4.1.4325.2.8.1.1.12
aniDevFilterIpSourceEndThe highest bound value for the source port number.

Refer to the Well known ports list under
aniIpFilterIpSourceStart description.
In addition to the list, the user can enter any other
value as well.
…
Integer32r/w
Constraints:
range: 0-65535
.1.3.6.1.4.1.4325.2.8.1.1.13
aniDevFilterIpDestStartThe lowest bound value for the destination port number.

Refer to the Well known ports list under
aniIpFilterIpSourceStart description.
In addition to the list, the user can enter any other
value as well.…
Integer32r/w
Constraints:
range: 0-65535
.1.3.6.1.4.1.4325.2.8.1.1.14
aniDevFilterIpDestEndThe highest bound value for the destination port number.

Refer to the Well known ports list under
aniIpFilterIpSourceStart description.
In addition to the list, the user can enter any other
value as well…
Integer32r/w
Constraints:
range: 0-65535
.1.3.6.1.4.1.4325.2.8.1.1.15
aniDevFilterIpOptionsThe Mask value for the IP Options.
No Operation (0x000001)
Route Record (0x000002)
Time Stamp (0x000040)
MTU Probe (0x000008)
MTU Reply (0x000010)
Trace Route (0x000080)
Address Extension (0x004000)
Loose Sour…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.4325.2.8.1.1.16
aniDevFilterIpSecOptionsThe IP Security Value.Enumerationr/w
Enumerated Values:
1top-secret
2secret
3confidential
4unclassified
.1.3.6.1.4.1.4325.2.8.1.1.17
aniDevFilterIcmpMsgTypeThe Message Type for ICMP Protocol.

This field is valid only if the aniDevFilterIpProtocol
is set to ICMP or not specified by the user.

Valid Range:

ICMP Message Type SubCo…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.4325.2.8.1.1.18
aniDevFilterIcmpSubcodeThe Subcode for ICMP Protocol.

This field is valid only if the aniDevFilterIpProtocol is
set to ICMP or not specified by the user.
If this field is specified then aniDevFilterIcmpMsgType
should already…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.4325.2.8.1.1.19
aniDevFilterTcpFlagsThe TCP Flags.

The valid range:
Urgent (0x20)
Acknowledgement (0x10)
Push (0x08)
Reset (0x04)
Sync (0x02)
Sync-Ack (0x12)
Finish (0x01)
Finish-Ack (0x11)

This field is valid only if the ani…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.4325.2.8.1.1.20
aniDevFilterDestMacMaskThe MAC address and mask value for destination.OctetStringr/w
Constraints:
range: 0-12
.1.3.6.1.4.1.4325.2.8.1.1.21
aniDevFilterSourceMacThe MAC Address of the source.SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
.1.3.6.1.4.1.4325.2.8.1.1.22
aniDevFilterEnetTypeThe Ethernet type value in the ethernet header.

The maximum length of the ethernet packet is 1500 (0x5DC).
The value of the ethernet type must be greater than 1500.

Appicable for Ethernet V…
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.4325.2.8.1.1.23
aniDevFilterLlcDSAPThe DSAP (Destination Service Access Point) value
in LLC Header.

Valid Range: 0 to 0xFF
Applicable for IEEE 802.3 Frame Format only.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.4325.2.8.1.1.24
aniDevFilterLlcSSAPThe SSAP (Source Service Access Point) value
in LLC Header.

Valid Range: 0 to 0xFF
Applicable for IEEE 802.3 Frame Format only.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.4325.2.8.1.1.25
aniDevFilterLlcControlThe Control Byte of the LLC Header.

Valid Range: 0 to 0xFF
Applicable for IEEE 802.3 Frame Format only.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.4325.2.8.1.1.26
aniDevFilterLocalCodeThe Local Code for SNAP ethernet type.
Applicable for IEEE 802.3 Frame Format only.
DSAP should be set to 0xAA, SSAP should be set to 0xAA,
Control Byte should be set to 0x03.

Valid range: 0 - 0xFFF…
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.4325.2.8.1.1.27
aniDevFilterRowStatusThis represents the state of an entry within the
table. It is used to manage creation and deletion of rows.
The values include:
active(1)
notInService(2)
notReady(3)
createAndGo(4)
createAndWait(5)
destroy(6)
…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.4325.2.8.1.1.28
aniDevFilterUserPriorityHiThe high priority byte of the user priority.

The user priority specifies the matching
parameters for the IEEE 802.1P user_priority
bits. An Ethernet packet with IEEE 802.1P
user_priority value 'priority…
Integer32r/w
Constraints:
range: 0-7
.1.3.6.1.4.1.4325.2.8.1.1.29
aniDevFilterUserPriorityLoThe low priority byte of the user priority.

The user priority specifies the matching
parameters for the IEEE 802.1P user_priority
bits. An Ethernet packet with IEEE 802.1P
user_priority value 'priority'…
Integer32r/w
Constraints:
range: 0-7
.1.3.6.1.4.1.4325.2.8.1.1.30
aniDevFilterVlanIdStartThe lower limit for the VLAN ID.
This value is used to specify the lower limit in the
range. Any IEEE 802.1P packet from a customer's VLAN
that falls into the range matches the rule.
aniDevFilterVlanIdStart and aniDevF…
Integer32r/w
Constraints:
range: 0-4095
.1.3.6.1.4.1.4325.2.8.1.1.31
aniDevFilterVlanIdEndThe upper limit for the VLAN ID.
This value is used to specify the upper limit in the
range. Any IEEE 802.1P packet from a customer's VLAN
that falls into the range matches the rule.
aniUSClassifierVlanIdStart and aniU…
Integer32r/w
Constraints:
range: 0-4095
.1.3.6.1.4.1.4325.2.8.1.1.32
.1.3.6.1.4.1.4325.2.8.2 · 1 row entry · 2 columns
Uses the aperto variant from /opt/observium/mibs/aperto.
Command help
Walk aniDevFilterIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DEVFILTER-MIB' -M '/opt/observium/mibs/aperto:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DEVFILTER-MIB::aniDevFilterIfTable'
This table allows the user to enable/disable Filtering
per interface basis.
aniDevFilterIfEntry row .1.3.6.1.4.1.4325.2.8.2.1
An entry containing objects for each IP Filter
interface configured.
Column Syntax OID
aniDevFilterIfIdentifierThe Interface Type.
On SU, only ethernet(1) and wireless-port1(2) are valid.

On BSU, ethernet(1) and all configured wireless interfaces
-- wireless-port1(2), wireless-port2(3), wireless-port3(4),
wirel…
Enumerationr/w
Enumerated Values:
1ethernet
2wireless-port1
3wireless-port2
4wireless-port3
5wireless-port4
6wireless-port5
7wireless-port6
.1.3.6.1.4.1.4325.2.8.2.1.1
aniDevFilterIfFlagThe flag to enable or disable filtering on
a particular interface.

The default value depends on whether a rule is configured
on the particular interface or not. When a rule is configured
on the interface…
Enumerationr/w
Enumerated Values:
1enable
2disable
.1.3.6.1.4.1.4325.2.8.2.1.2