agentPethPowerLimitMax
DELL-POWER-ETHERNET-MIB ·
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.12
Object
The maximum power this port can be configured to provide, measured in Milliwatts.
Context
- MIB
- DELL-POWER-ETHERNET-MIB
- OID
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.12- Type
- column
- Access
- readonly
- Status
- current
- Units
- Milliwatts
- Parent
- agentPethPsePortEntry
- Table
- agentPethPsePortTable
- Siblings
- 12
Syntax
Milliwatts SNMPv2-SMIGauge32
- Source
- SNMPv2-SMIGauge32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| agentPethPowerLimit The configured maximum power this port can provide to an
attached device measured in Milliwatts. | column | Milliwatts SNMPv2-SMIGauge32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.1 |
| agentPethPortReset A value of reset(1) is used to move the pse port dot3at state to idle. A
read on this object will always return the value none(0). The value none(0)
can not be forcibly set by the… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.10 |
| agentPethPowerLimitMin The minimum power this port can be configured to provide, measured in Milliwatts. | column | Milliwatts SNMPv2-SMIGauge32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.11 |
| agentPethPowerClassifications Classification is a way to tag different terminals on the
Power over LAN network according to their power consumption.
Devices such as IP telephones, WLAN access points and others… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.13 |
| agentPethOutputPower The power this port is supplying to an attached device measured
in Milliwatts. | column | Milliwatts SNMPv2-SMIGauge32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.2 |
| agentPethOutputCurrent The current this port is supplying to an attached device measured
in Milliamps. | column | Milliamps SNMPv2-SMIGauge32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.3 |
| agentPethOutputVolts The voltage this port is supplying to an attached device measured
in Volts. | column | Volts SNMPv2-SMIGauge32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.4 |
| agentPethTemperature The temperature measured at this port of the PoE Controller. It is
measured in degree celcius. | column | DEGREES SNMPv2-SMIGauge32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.5 |
| agentPethPowerLimitType Describes or controls the maximum power that a port can deliver.
A value of dot3at(1) means that the port power limit is as per
the dot3at class of the PD attached.
A value of use… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.6 |
| agentPethHighPowerEnable true (1) The PSE port can deliver power up to 32Watts.
false(2) The PSE port can deliver power up to 18Watts | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.7 |
| agentPethPowerDetectionType Describes PD detection mechanism performed by the PSE port.
A value of none(0) means no detection is done.
A value of dot3atonly(2) means that IEEE 802.3at detection scheme is use… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.8 |
| agentPethFaultStatus Describes the error description when the pse port is in fault status.
A value of none(0) specifies that the pse port is not in any error state.
A value of mpsAbsent(1) specifies t… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.15.1.1.1.9 |