bertOwner

CISCO-WAN-SRM-BERT-MIB · .1.3.6.1.4.1.351.110.6.1.3
MIB view Table view

Object

scalar SNMPv2-TCDisplayString 
This refers to the user who owns the BERT resources.
If the user is a CLI user, then this is username.
If it is SNMP Manager(For example Cisco Wan Manager),
then this would be the IP address.
For example, this value can be, 192.9.209.157 
within quotes.

Context

MIB
CISCO-WAN-SRM-BERT-MIB
OID
.1.3.6.1.4.1.351.110.6.1.3
Type
scalar
Access
readonly
Status
current
Parent
bert
Siblings
27

Syntax

SNMPv2-TCDisplayString
Source
SNMPv2-TCDisplayString
Base type
OctetString

Values & Constraints

Type Constraints
range: 0..255

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
bertControl
This object controls all the SET operations on this MIB group. acquireBert : Acquire BERT resources. cnfBert : Configure the required BERT test. startBert : The configur…
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.1
bertMode
specifies the mode, the BERT module is to be configured for.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.10
bertDeviceToLoop
This shows the type of the end device and the type of the loopback used (latching/nonlatching/polynomial).
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.11
bertDS0DPIterationCount
The Iteration Register needs to be programmed in SRM when DSO drop loop option is selected in bertDeviceToLoop. The value to be programmed there is minus one of this object value,…
scalarInteger32.1.3.6.1.4.1.351.110.6.1.12
bertPattern
This variable determines BERT pattern to be transmitted.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.13
bertLoopback
specifies the type of loopback to be (d)established.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.14
bertLoopbackOperation
specifies the operation of loopback (up or down).
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.15
bertDS0Speed
represents the ds0 speed of the test running.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.16
bertTimeSlots
represents the number of ds0s in the test medium chosen.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.351.110.6.1.17
bertStartTime
The syntax is hh:mm:ss The time zone is as configured in the shelf.
scalarOctetString.1.3.6.1.4.1.351.110.6.1.18
bertStartDate
On MGX 8220, the syntax is mm/dd/yy On MGX 8850, the syntax is mm/dd/yyyy.
scalarOctetString.1.3.6.1.4.1.351.110.6.1.19
bertResourceStatus
All of bert resources can be used by only one user at a time. This gives the status of the resources.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.2
bertBitCount
This shows the number of bits transmitted.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.351.110.6.1.20
bertBitErrorCount
This shows the number of bits received in error.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.351.110.6.1.21
bertErrorInjectCount
This shows the number of times error was injected.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.351.110.6.1.22
bertCleanupAction
When the BERT has to be stopped or aborted (due to card state changes), this object would give the exact action to take. The bert related changes to the shelf, then, can be cle…
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.23
bertAbortReason
when the BERT is aborted, this object would give the reason for that.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.24
bertDDSSeekResultsTableFirstIndex
Denotes the index of the oldest entry in the table. A value of zero means that there are no entries in the table.
scalarInteger32.1.3.6.1.4.1.351.110.6.1.25
bertDDSSeekResultsTableLastIndex
Denotes the index of the latest entry in the table. A value of zero means that there are no entries in the table.
scalarInteger32.1.3.6.1.4.1.351.110.6.1.26
bertDDSSeekResultsTable
This table contains all available DDS patterns detected and latched by an interaface(lines,ports etc) configured to detect DDS patterns.
table-.1.3.6.1.4.1.351.110.6.1.27
bertSupportedTestsTable
A list of supported tests for a given SM.
table-.1.3.6.1.4.1.351.110.6.1.28
bertUserId
This identifies the user who wants to do a SET operation on this group. This will be compared against bertOwner and access will be given only if it matches. Hence, for every SET r…
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.351.110.6.1.4
bertStatus
This variable provides the status of BERT in the shelf.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.5
bertSlotNumber
specifies the physical slot number of the Service Module which is to run BERT For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30. Required fo…
scalarInteger32.1.3.6.1.4.1.351.110.6.1.6
bertTestMedium
specifies whether the bert is to test a port or an entire T1/E1 line. No default value for this, it has to be set if bert is configured.
scalarEnumeration.1.3.6.1.4.1.351.110.6.1.7
bertPort
specifies the port number for BERT.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.351.110.6.1.8
bertLine
specifies the line number for BERT. If the test medium is port, this represents the line to which the port belongs.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.351.110.6.1.9