bertControl
CISCO-WAN-SRM-BERT-MIB ·
.1.3.6.1.4.1.351.110.6.1.1
Object
scalar
r/w
Enumeration
This object controls all the SET operations on this MIB group. acquireBert : Acquire BERT resources. cnfBert : Configure the required BERT test. startBert : The configured test has to be started. modBert : Modify parameters for the ongoing BERT test. delBert : Running BERT test has to be stopped. The above list shows the sequence in which the SET operations on this group need to be done, ideally. Bert can be operated upon only with bertUserId and bertSlotNumber. The default value is 0, means no action.
Context
- MIB
- CISCO-WAN-SRM-BERT-MIB
- OID
.1.3.6.1.4.1.351.110.6.1.1- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- bert
- Siblings
- 27
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | acquireBert |
2 | releaseBert |
3 | cnfBert |
4 | startBert |
5 | modBert |
6 | delBert |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bertMode specifies the mode, the BERT module is to be
configured for. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.10 |
| bertDeviceToLoop This shows the type of the end device and the type of the
loopback used (latching/nonlatching/polynomial). | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.11 |
| bertDS0DPIterationCount The Iteration Register needs to be programmed in SRM when
DSO drop loop option is selected in bertDeviceToLoop. The
value to be programmed there is minus one of this object value,… | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.1.12 |
| bertPattern This variable determines BERT pattern to
be transmitted. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.13 |
| bertLoopback specifies the type of loopback to be (d)established. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.14 |
| bertLoopbackOperation specifies the operation of loopback (up or down). | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.15 |
| bertDS0Speed represents the ds0 speed of the test running. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.16 |
| bertTimeSlots represents the number of ds0s in the test medium chosen. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.6.1.17 |
| bertStartTime The syntax is hh:mm:ss
The time zone is as configured in the shelf. | scalar | OctetString | .1.3.6.1.4.1.351.110.6.1.18 |
| bertStartDate On MGX 8220, the syntax is mm/dd/yy
On MGX 8850, the syntax is mm/dd/yyyy. | scalar | OctetString | .1.3.6.1.4.1.351.110.6.1.19 |
| bertResourceStatus All of bert resources can be used by only one user at a time.
This gives the status of the resources. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.2 |
| bertBitCount This shows the number of bits transmitted. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.6.1.20 |
| bertBitErrorCount This shows the number of bits received in error. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.6.1.21 |
| bertErrorInjectCount This shows the number of times error was injected. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.6.1.22 |
| bertCleanupAction When the BERT has to be stopped or aborted (due to card state
changes), this object would give the exact action to take.
The bert related changes to the shelf, then, can be cle… | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.23 |
| bertAbortReason when the BERT is aborted, this object would give the
reason for that. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.24 |
| bertDDSSeekResultsTableFirstIndex Denotes the index of the oldest entry in the table.
A value of zero means that there are no entries in
the table. | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.1.25 |
| bertDDSSeekResultsTableLastIndex Denotes the index of the latest entry in the table.
A value of zero means that there are no entries in
the table. | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.1.26 |
| bertDDSSeekResultsTable This table contains all available DDS patterns detected
and latched by an interaface(lines,ports etc) configured
to detect DDS patterns. | table | - | .1.3.6.1.4.1.351.110.6.1.27 |
| bertSupportedTestsTable A list of supported tests for a given SM. | table | - | .1.3.6.1.4.1.351.110.6.1.28 |
| bertOwner This refers to the user who owns the BERT resources.
If the user is a CLI user, then this is username.
If it is SNMP Manager(For example Cisco Wan Manager),
then this would be the… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.351.110.6.1.3 |
| bertUserId This identifies the user who wants to do a SET operation
on this group. This will be compared against bertOwner
and access will be given only if it matches. Hence, for
every SET r… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.351.110.6.1.4 |
| bertStatus This variable provides the status of BERT in the shelf. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.5 |
| bertSlotNumber specifies the physical slot number of the Service Module
which is to run BERT
For MGX 8220, the range is 5-14.
For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30.
Required fo… | scalar | Integer32 | .1.3.6.1.4.1.351.110.6.1.6 |
| bertTestMedium specifies whether the bert is to test a port or an
entire T1/E1 line.
No default value for this, it has to be set if
bert is configured. | scalar | Enumeration | .1.3.6.1.4.1.351.110.6.1.7 |
| bertPort specifies the port number for BERT. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.6.1.8 |
| bertLine specifies the line number for BERT. If the test medium
is port, this represents the line to which the
port belongs. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.6.1.9 |