cssGroupRedundantPowerState
CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB ·
.1.3.6.1.4.1.9.10.44.1.2.1.1.13
Object
column
Enumeration
Indicates the state of the external/backup power
supply.
off : the switch is not connected to a redundant
power source.
healthy : a redundant power source is connected to
the switch and the power source is
operating correctly.
faulty : a redundant power source is connected to
the switch but a failure exists in the
power system.
Context
- MIB
- CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB
- OID
.1.3.6.1.4.1.9.10.44.1.2.1.1.13- Type
- column
- Access
- readonly
- Status
- current
- Parent
- cssGroupEntry
- Table
- cssGroupTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | off |
2 | healthy |
3 | faulty |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cssGroupID The hub identifier of unit in a stack. | column | HubNumber | .1.3.6.1.4.1.9.10.44.1.2.1.1.1 |
| cssGroupInternalPowerState Indicates the state of the internal power supply.
off : The internal power supply is off.
on : The internal power supply is on. | column | Enumeration | .1.3.6.1.4.1.9.10.44.1.2.1.1.12 |
| cssGroupReset Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not run
the POST (Power On Self Test).
Setting this object to noRese… | column | Enumeration | .1.3.6.1.4.1.9.10.44.1.2.1.1.14 |
| cssGroupConfigDefaultReset Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not
run the POST (Power On Self Test). All
configuration parameters will revert to… | column | Enumeration | .1.3.6.1.4.1.9.10.44.1.2.1.1.15 |
| cssGroupIsolatedState Setting this object to isolated(1) causes this hub
to be isolated from the back plane bus. Setting
this object to attached(2) causes this hub to be
attached to the back plane bus. | column | Enumeration | .1.3.6.1.4.1.9.10.44.1.2.1.1.16 |
| cssGroupType The model type of the hub unit | column | Enumeration | .1.3.6.1.4.1.9.10.44.1.2.1.1.2 |
| cssGroupSerialNo Serial number of the hardware. | column | OctetString | .1.3.6.1.4.1.9.10.44.1.2.1.1.4 |
| cssGroupBoardRevision Hardware version of the repeater board. | column | Integer32 | .1.3.6.1.4.1.9.10.44.1.2.1.1.5 |
| cssGroupAgentBootVersion Returns the version number of the dual-speed hub
BOOT software residing in flash. The format is 'V1.2.3'. | column | OctetString | .1.3.6.1.4.1.9.10.44.1.2.1.1.6 |
| cssGroupAgentFirmwareVersion Returns the version number of the dual-speed hub
firmware residing in flash. The format is 'V1.2.3'. | column | OctetString | .1.3.6.1.4.1.9.10.44.1.2.1.1.7 |
| cssGroupAgentStatus Status of this hub agent. Each stack allows only
one SNMP primary agent.
notPresent(1): The hub does not have an agent.
primary(2): The agent of this hub is a prima… | column | Enumeration | .1.3.6.1.4.1.9.10.44.1.2.1.1.8 |
| cssGroupAgentPhysAddress MAC address of this hub's agent | column | RFC1213-MIBPhysAddress | .1.3.6.1.4.1.9.10.44.1.2.1.1.9 |