CISCO-SIBU-STACKABLE-DUAL-SPEED-HUB-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
3
Rows
3
Columns
29
cssGroupTable
table.1.3.6.1.4.1.9.10.44.1.2.1
·
1 row entry
·
13 columns
A list of member hubs in the stack.
Configuration parameters for an individual hub.
An entry is created by default for the master unit
in the stack. A entry is created (removed) when
a hub is connected to (removed from) the stack.
An entry is created by default for the master unit
in the stack. A entry is created (removed) when
a hub is connected to (removed from) the stack.
Indexes
SNMP-REPEATER-MIBrptrGroupIndex
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
cssGroupID
The hub identifier of unit in a stack.
|
HubNumber Textual Convention: HubNumber Integer32Type Constraints: range: 1..2147483647 |
.1.3.6.1.4.1.9.10.44.1.2.1.1.1 |
||||||||||||
|
cssGroupType
The model type of the hub unit
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.2 |
||||||||||||
|
cssGroupSerialNo
Serial number of the hardware.
|
OctetString Constraints: range: 0-20 |
.1.3.6.1.4.1.9.10.44.1.2.1.1.4 |
||||||||||||
|
cssGroupBoardRevision
Hardware version of the repeater board.
|
Integer32 Constraints: range: 0-2147483647 |
.1.3.6.1.4.1.9.10.44.1.2.1.1.5 |
||||||||||||
|
cssGroupAgentBootVersion
Returns the version number of the dual-speed hub
BOOT software residing in flash. The format is 'V1.2.3'. |
OctetString Constraints: range: 0-8 |
.1.3.6.1.4.1.9.10.44.1.2.1.1.6 |
||||||||||||
|
cssGroupAgentFirmwareVersion
Returns the version number of the dual-speed hub
firmware residing in flash. The format is 'V1.2.3'. |
OctetString Constraints: range: 0-8 |
.1.3.6.1.4.1.9.10.44.1.2.1.1.7 |
||||||||||||
|
cssGroupAgentStatus
Status of this hub agent. Each stack allows only
one SNMP primary agent. notPresent(1): The hub does not have an agent. primary(2): The agent of this hub is a primary agent. backup(3) : The agent of this … |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.8 |
||||||||||||
|
cssGroupAgentPhysAddress
MAC address of this hub's agent
|
RFC1213-MIBPhysAddress Textual Convention: RFC1213-MIBPhysAddress OctetString |
.1.3.6.1.4.1.9.10.44.1.2.1.1.9 |
||||||||||||
|
cssGroupInternalPowerState
Indicates the state of the internal power supply.
off : The internal power supply is off. on : The internal power supply is on. |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.12 |
||||||||||||
|
cssGroupRedundantPowerState
Indicates the state of the external/backup power
supply. off : the switch is not connected to a redundant power source. healthy : a redundant power source is connected to the switc… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.13 |
||||||||||||
|
cssGroupReset
Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to noReset(1) has no effect. The switch always re… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.14 |
||||||||||||
|
cssGroupConfigDefaultReset
Setting this object to reset(2) causes a complete
reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parameters will revert to their factory default settings. … |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.15 |
||||||||||||
|
cssGroupIsolatedState
Setting this object to isolated(1) causes this hub
to be isolated from the back plane bus. Setting this object to attached(2) causes this hub to be attached to the back plane bus. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.2.1.1.16 |
cssRepeaterPortTable
table.1.3.6.1.4.1.9.10.44.1.3.1
·
1 row entry
·
5 columns
The list of repeater port configurations on each hub unit.
Configuration parameters for an individual repeater
port on a hub. The value of rptrPortIndex also
indicates the physical port number of the port in
the hub. An entry is created for each repeater port in
a hub when the …
port on a hub. The value of rptrPortIndex also
indicates the physical port number of the port in
the hub. An entry is created for each repeater port in
a hub when the …
Indexes
SNMP-REPEATER-MIBrptrPortGroupIndex SNMP-REPEATER-MIBrptrPortIndex
| Column | Syntax | OID | ||||||
|---|---|---|---|---|---|---|---|---|
|
cssRepeaterPortName
A descriptive string of up to 20 characters used
by the network administrator to name a port. |
OctetStringr/w Constraints: range: 0-20 |
.1.3.6.1.4.1.9.10.44.1.3.1.1.1 |
||||||
|
cssRepeaterPortControllerRevision
Returns the revision number of the port controller.
|
Integer32 Constraints: range: 0-2147483647 |
.1.3.6.1.4.1.9.10.44.1.3.1.1.2 |
||||||
|
cssRepeaterPortSpeedAdmin
Set to tenMbps(1) to operate in 10Mbps speed mode.
Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection. … |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.3.1.1.3 |
||||||
|
cssRepeaterPortSpeedStatus
The operating speed of the port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.3.1.1.4 |
||||||
|
cssRepeaterPortLinkStatus
The current port link status.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.3.1.1.5 |
cssSwitchPortTable
table.1.3.6.1.4.1.9.10.44.1.4.1
·
1 row entry
·
11 columns
A list of switched ports on extension module on a each hub unit in the stack.
Configuration parameters for an individual switch
module port. An entry is created for each switch port
on a module is inserted into a hub in the stack.
The corresponding entries are removed when the module
is removed f…
module port. An entry is created for each switch port
on a module is inserted into a hub in the stack.
The corresponding entries are removed when the module
is removed f…
Indexes
| Column | Syntax | OID | ||||||
|---|---|---|---|---|---|---|---|---|
|
cssSwitchPortModuleID
Unique ID number of a module unit in a hub as used
in the command line interface. |
Integer32 Constraints: range: 1-2147483647 |
.1.3.6.1.4.1.9.10.44.1.4.1.1.1 |
||||||
|
cssSwitchPortPortID
The unique ID identifying a port on an extension module
on a hub as used in the command line interface. |
Integer32 Constraints: range: 1-2147483647 |
.1.3.6.1.4.1.9.10.44.1.4.1.1.2 |
||||||
|
cssSwitchPortName
A descriptive string of up to 20 characters used by the
network administrator to name a switch port. |
OctetStringr/w Constraints: range: 0-20 |
.1.3.6.1.4.1.9.10.44.1.4.1.1.3 |
||||||
|
cssSwitchPortType
Type of switch module in this hub.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.4 |
||||||
|
cssSwitchPortControllerRevision
The revision number of the port controller.
|
Integer32 Constraints: range: 0-2147483647 |
.1.3.6.1.4.1.9.10.44.1.4.1.1.5 |
||||||
|
cssSwitchPortState
Setting this object to enabled(1) enables the port.
Setting this object to disabled(2) disables the port. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.6 |
||||||
|
cssSwitchPortDuplexAdmin
Set to fullDuplex(1) to operate in full duplex mode: port
will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to operate in normal mode. Set to autoNegotiate(3) to allow the… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.7 |
||||||
|
cssSwitchPortDuplexStatus
The operating duplex mode of the switched port.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.8 |
||||||
|
cssSwitchPortSpeedAdmin
Set to tenMbps(1) to operate in 10Mbps speed mode. Set to
oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate the operating speed with the other end of the conn… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.9 |
||||||
|
cssSwitchPortSpeedStatus
The operating speed of the switched port.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.10 |
||||||
|
cssSwitchPortLinkStatus
Indicates the link STATUS of switch port.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.9.10.44.1.4.1.1.11 |