cmmIpPeerCfgSessionTarget

CISCO-MMAIL-DIAL-CONTROL-MIB · .1.3.6.1.4.1.9.9.102.1.1.1.1.2
Commands MIB view Table view

Object

column r/w SNMPv2-TCDisplayString 
The object specifies the session target of the peer.
Session Targets definitions:
The session target has the syntax used by the IETF service
location protocol. The syntax is as follows:
              
mapping-type:type-specific-syntax
              
The mapping-type specifies a scheme for mapping the 
matching dial string to a session target. The 
type-specific-syntax is exactly that, something that the 
particular mapping scheme can understand.
For example,
Session target    mailto:+$d$@fax.cisco.com
              
The valid Mapping type definitions for the peer are as 
follows:
mailto  - Syntax: mailto:w@x.y.z

Context

MIB
CISCO-MMAIL-DIAL-CONTROL-MIB
OID
.1.3.6.1.4.1.9.9.102.1.1.1.1.2
Type
column
Access
readwrite
Status
current
Parent
cmmIpPeerCfgEntry
Groups
1

Net-SNMP examples

How SNMP and these commands work

Walk the column to discover its indexed instances, or supply every index to read one instance.

Walk the column
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MMAIL-DIAL-CONTROL-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MMAIL-DIAL-CONTROL-MIB::cmmIpPeerCfgSessionTarget'
More examples
Read one indexed instance
/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'CISCO-MMAIL-DIAL-CONTROL-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MMAIL-DIAL-CONTROL-MIB::cmmIpPeerCfgSessionTarget.<ifIndex>'
Translate to a numeric OID
/usr/bin/snmptranslate -Pud -Ir -On -m 'CISCO-MMAIL-DIAL-CONTROL-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'CISCO-MMAIL-DIAL-CONTROL-MIB::cmmIpPeerCfgSessionTarget'

Syntax

SNMPv2-TCDisplayString
Source
SNMPv2-TCDisplayString
Base type
OctetString
Display format
255a
Type Description
Represents textual information taken from the NVT ASCII
          
character set, as defined in pages 4, 10-11 of RFC 854.
          
To summarize RFC 854, the NVT ASCII repertoire specifies:
          
  - the use of character codes 0-127 (decimal)
          
  - the graphics characters (32-126) are interpreted as
    US ASCII
          
  - NUL, LF, CR, BEL, BS, HT, VT and FF have the special
    meanings specified in RFC 854
          
  - the other 25 codes have no standard interpretation
          
  - the sequence 'CR LF' means newline
          
  - the sequence 'CR NUL' means carriage-return
          
  - an 'LF' not preceded by a 'CR' means moving to the
    same column on the next line.
          
  - the sequence 'CR x' for any x other than LF or NUL is
    illegal.  (Note that this also means that a string may
    end with either 'CR LF' or 'CR NUL', but not with CR.)
          
Any object defined using this syntax may not exceed 255
characters in length.

Values & Constraints

Type Constraints
range: 0..255

Conformance

Member of
cmmdcPeerCfgGroup