rpmChanRestrictTrkType
CISCO-MGX82XX-RPM-CONN-MIB ·
.1.3.6.1.4.1.351.110.5.2.10.1.1.1.21
Object
column
Enumeration
Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satellite trunks or terrestrial trunks, or it can be on any type of trunk.
Context
- MIB
- CISCO-MGX82XX-RPM-CONN-MIB
- OID
.1.3.6.1.4.1.351.110.5.2.10.1.1.1.21- Type
- column
- Access
- readonly
- Status
- current
- Parent
- rpmChanGrpEntry
- Table
- rpmChanGrpTable
- Siblings
- 36
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | noRestriction |
2 | terrestrialTrunk |
3 | satelliteTrunk |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rpmChanSlotNum Specifies the slot number of the RPM card. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.1 |
| rpmChanLocalVci This VCI together with the local
VPI and NSAP represents the local
end point in this connection. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.10 |
| rpmChanLocalNsap This object identifies the local NSAP address.
The bytes are mapped as follows:
prefix : 13 bytes
Cisco ID : 2 bytes
Reserved : 2 bytes
Slot/Port :… | column | RpmNsapAddress | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.11 |
| rpmChanRemoteVpi This VPI together with the remote
VCI and NSAP represents the remote
end point in this connection. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.12 |
| rpmChanRemoteVci This VCI together with the remote
VPI and NSAP represents the remote
end point in this connection. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.13 |
| rpmChanRemoteNsap This object identifies the remote NSAP address.
The bytes are mapped as follows:
prefix : 13 bytes
Cisco ID : 2 bytes
Reserved : 2 bytes
Slot/Port … | column | RpmNsapAddress | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.14 |
| rpmChanType This object identifies the channel type
svc(1) : Switched Virtual Connection
pvc(2) : Permanent Virtual Connection
spvc(3) : Soft PVC. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.15 |
| rpmChanConnType This specifies the connection type
vpc(1) : Virtual Path Connection
vcc(1) : Virtual Channel Connection | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.16 |
| rpmChanServiceType This object identifies the connection service type.
cbr (1) : Constant Bit Rate
vbr (2) : Variable Bit Rate
ubr (4) : Unspecified Bit Rate
atfr (5) : ATM… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.17 |
| rpmChanMastership This specifies which end of the connection
is the master. This is used by PXM to determine
if this end point is master or slave. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.18 |
| rpmChanRtePriority This is also known as class of service,
it is used by PXM to determine how important
this connection is when selecting connections
to route. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.19 |
| rpmChanInterface This is the RPM's backplane interface.
Currently there is only one interface. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.2 |
| rpmChanMaxCost Maximum allowed cost. It is related to
Cost Based Routing. This is used by PXM so
that it won't choose a path with a cost
greater than this configured level. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.20 |
| rpmChanPCR Peak cell rate.(in cells per sec.) | column | cells-per-second Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.22 |
| rpmChanRemotePCR Peak cell rate of the remote endpoint of
the connection. If not set, its value will
be same as the value of rpmChanPCR. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.23 |
| rpmChanMCR Minimum cell rate.(in cells per sec.). | column | cells-per-second Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.24 |
| rpmChanRemoteMCR Minimum cell rate of the remote endpoint.
If this is not set, its value will be same
as value of rpmChanMCR. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.25 |
| rpmChanPercentUtil This is the expected long-term utilization of the
channel by this end-point. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.26 |
| rpmChanRemotePercentUtil This is the expected long-term utilization of the
channel by the other end-point. If this is not
specified in the connection setup request,
it'll be set to be the same as the lo… | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.27 |
| rpmChanEncapType This object identifies the ATM adaptation
layer (AAL) and Encapsulation type.
aal5snap - LLC/SNAP precedes the protocol datagram.
aal34smds - Encapsulation for S… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.28 |
| rpmChanMidLow Starting Message Identifier Number for this PVC. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.29 |
| rpmChanNum This object identifies the channel number.
This is also called Logical Connection Number(LCN).
This is a unique number which identifies a
connection.
The LCN maps VPI and VCI.
… | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.3 |
| rpmChanMidHigh Ending Message Identifier Number for this PVC. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.30 |
| rpmChanBurstSize The Maximum number of ATM cells the
virtual circuit can transmit. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.31 |
| rpmChanInArpFreq Specifies how often Inverse ARP datagrams
will be sent on this virtual circuit. The
value zero will disable the IN-ARP for this
channel. This object is supported only
for the valu… | column | minutes Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.32 |
| rpmChanOAMloopback This object specifies how often to generate
an OAM F5 loopback cell from this virtual circuit.
The value zero will disable generation of OAM F5
loopback cells. | column | seconds Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.33 |
| rpmChanState This indicates the status of this channel.
1 ==> notConfigured
2 ==> active
3 ==> failed.
Currently 'failed' state is not supported.
When the channel is not added, … | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.34 |
| rpmChanVirtualTemplate Specifies the Virtual Template used for CISCO PPP.
If it is not using Virtual Template then this value
is zero. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.35 |
| rpmChanAbrRDF This is valid only for ABR Service Type.
Rate Decrease Factor: Controls the rate
decrease which occurs when backward RM-cells
with CI=1 are received. Larger values lead to
fast… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.36 |
| rpmChanAbrRIF This is valid only for ABR Service Type.
Rate Increase Factor: Controls the rate
increase which occurs when a backward RM-cell
is received with CI=0 and NI=0. Larger values
lea… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.37 |
| rpmChanRowStatus This indicates the status of this channel.
add(1) : Channel is added.
del(2) : channel is deleted.
mod(3) : Set to this value before modifying objects
rela… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.4 |
| rpmChanVcd Virtual Circuit Descriptor. A unique number
which identifies a connection. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.5 |
| rpmChanVpi The VPI value for this channel.
For VPC, VPI range is 1..255 and
LCN range is 3841..4095.
LCN = VPI + 3840 | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.6 |
| rpmChanVci The VCI value for this channel.
For VCC, VCI range is 1..3825, and
LCN range is 16..3840.
LCN = VCI + 16. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.7 |
| rpmChanSubInterface This is the RPM's backplane sub-interface. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.8 |
| rpmChanLocalVpi This VPI together with the local VCI
and NSAP represents the local end point
in this connection. The VPI value is zero for
rpmChanConnType value of vcc(2). | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.10.1.1.1.9 |