lineType

CISCO-MGX82XX-DSX1-MIB · .1.3.6.1.4.1.351.110.4.3.1.1.1.1.4

Object

column r/w Enumeration

This variable indicates  the  variety  of  DS1
Line  implementing  this  circuit.  The type of
circuit affects the number of bits  per  second
that  the circuit can reasonably carry, as well
as the interpretation of the  usage  and  error statistics.  
The values, in sequence, describe:
TITLE:        SPECIFICATION:
dsx1ESF       Extended SuperFrame DS1
dsx1D4        AT&T D4 format DS1
dsx1E1        CCITT Recommendation G.704
	       (Table 4a)
dsx1E1-CRC    CCITT Recommendation G.704
      (Table 4b)
dsxE1-MF      G.704 (Table 4a) with TS16
      multiframing enabled
dsx1E1-CRC-MF G.704 (Table 4b) with TS16
      multiframing enabled
dsx1E1clearchannel E1 clear channel, all DS0s can be used 
dsx1E1Q50     G.704 (table 14) In TS16 bits 5,7,8 will be
             set to 100 for all other cases bits 5,7,8 will
             have a value of 111. 
dsx1E1Q50CRC  same as dsx1E1Q50 but with CRC.
              
NOTE: All E1, E1-CRC, E1-MF or E1-CRC-MF are using DS0 
on slot 1 for signaling and E1-MF or E1-CRC-MF use DS0 
on slot 17 for synchronization.
(Slot 1 and 16 is based on index 1 to 32 DS0) 
All DS0s can be used for any port when lineType is
dsx1E1clearchannel. 
On a CESM card, only 'dsx1E1clearchannel' option is supported.
              
When the lineType is dsx1E1Q50 the bits 5,7,8 of TS16
of frame zero will be forced to 100 else it will be 111.
              
The default value for T1 is 'dsx1ESF' and for E1 
is 'dsx1E1CCS'.

Context

MIB: CISCO-MGX82XX-DSX1-MIB
OID: .1.3.6.1.4.1.351.110.4.3.1.1.1.1.4
Type: column
Access: readwrite
Status: current
Parent: dsx1CnfGrpEntry
Table: dsx1CnfGrpTable
Siblings: 14

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	dsx1ESF
`2`	dsx1D4
`3`	dsx1E1
`4`	dsx1E1CRC
`5`	dsx1E1MF
`6`	dsx1E1CRC-MF
`7`	dsx1E1clearchannel
`8`	dsx1E1Q50
`9`	dsx1E1Q50CRC

Related Objects

Sibling Objects

Object	Type	Syntax	OID
lineNum This object is the identifier of a DS1/E1 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1/E1 interface, it should hav…	column	Integer32	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.1`
lineUsedTimeslotsBitMap Bit map of used DS0 for this line.	column	Integer32	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.10`
lineLoopbackCodeDetection Enable detection of line Loopback Codes	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.11`
lineBERTEnable This variable enables Bit Error Rate Testing(BERT).	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.12`
lineBERTPattern This variable determines BERT pattern to transmit	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.13`
lineBERTResult This shows the result of the BERT.	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.14`
bERTResultClrButton This clears the result of the BERT.	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.15`
lineConnectorType This variable indicates the connector as well as the backcard type. 1 = T1; 2 = E1. This field is set to unused(4) for FRSM-VHS cards.	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.2`
lineEnable This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify In FRSM-2CT3, if the DS3 line is enabled, then the DS1 channels for that line will all be aut…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.3`
lineCoding This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS(1): refers the…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.5`
lineLength This is not a standard RFC 1407 DS1 variable, it is specific to BASIS implementation. It specifies the line length: 1 - 0 to 110 ft (T1 line only) 2 - 110 to 220 ft (T1 line only…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.6`
lineXmtClockSource The source of Transmit Clock. loopTiming(1): indicates that the recovered receive clock is used as the transmit clock. localTiming(2)…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.7`
lineLoopbackCommand This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback sta…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.8`
lineSendCode This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal d…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.9`