lineLoopbackCommand
CISCO-MGX82XX-DSX1-MIB ·
.1.3.6.1.4.1.351.110.4.3.1.1.1.1.8
Object
column
r/w
Enumeration
This variable represents the loopback confi-
guration of the DS1 interface. Agents support-
ing read/write access should return badValue in
response to a requested loopback state that the
interface does not support. The values mean:
dsx1NoLoop
Not in the loopback state. A device that
is not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx1RemoteLoop
The received signal at this interface is
looped through the device. Typically the
received signal is looped back for
retransmission after it has passed through
the device's framing function.
dsx1LocalLoop
The local data is looped back
dsx1PayloadLoop
This will loop only the payload and not
framing/sync bit.
Context
- MIB
- CISCO-MGX82XX-DSX1-MIB
- OID
.1.3.6.1.4.1.351.110.4.3.1.1.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dsx1CnfGrpEntry
- Table
- dsx1CnfGrpTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | dsx1NoLoop |
2 | dsx1RemoteLoop |
3 | dsx1LocalLoop |
4 | dsx1PayloadLoop |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| lineNum This object is the identifier of a DS1/E1
Interface on a managed device. If there is an
ifEntry that is directly associated with this
and only this DS1/E1 interface, it should hav… | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.1 |
| lineUsedTimeslotsBitMap Bit map of used DS0 for this line. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.10 |
| lineLoopbackCodeDetection Enable detection of line Loopback Codes | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.11 |
| lineBERTEnable This variable enables Bit Error Rate Testing(BERT). | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.12 |
| lineBERTPattern This variable determines BERT pattern to transmit | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.13 |
| lineBERTResult This shows the result of the BERT. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.14 |
| bERTResultClrButton This clears the result of the BERT. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.15 |
| lineConnectorType This variable indicates the connector as well
as the backcard type. 1 = T1; 2 = E1.
This field is set to unused(4) for FRSM-VHS cards. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.2 |
| lineEnable This variable disables, enables or modifies a line
1 - disable
2 - enable
3 - modify
In FRSM-2CT3, if the DS3 line is enabled, then the DS1
channels for that line will all be aut… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.3 |
| lineType This variable indicates the variety of DS1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably car… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.4 |
| lineCoding This variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
dsx1JBZS(1): refers the… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.5 |
| lineLength This is not a standard RFC 1407 DS1 variable, it is
specific to BASIS implementation. It specifies the line length:
1 - 0 to 110 ft (T1 line only)
2 - 110 to 220 ft (T1 line only… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.6 |
| lineXmtClockSource The source of Transmit Clock.
loopTiming(1): indicates that the recovered
receive clock is used as the
transmit clock.
localTiming(2)… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.7 |
| lineSendCode This variable indicates what type of code is
being sent across the DS1 interface by the dev-
ice. The values mean:
dsx1SendNoCode
sending looped or normal d… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.9 |