lineLoopbackCodeDetection
CISCO-MGX82XX-DSX1-MIB ·
.1.3.6.1.4.1.351.110.4.3.1.1.1.1.11
Object
column
r/w
Enumeration
Enable detection of line Loopback Codes
Context
- MIB
- CISCO-MGX82XX-DSX1-MIB
- OID
.1.3.6.1.4.1.351.110.4.3.1.1.1.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dsx1CnfGrpEntry
- Table
- dsx1CnfGrpTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | codeDetectDisabled |
2 | codeDetectEnabled |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| lineNum This object is the identifier of a DS1/E1
Interface on a managed device. If there is an
ifEntry that is directly associated with this
and only this DS1/E1 interface, it should hav… | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.1 |
| lineUsedTimeslotsBitMap Bit map of used DS0 for this line. | column | Integer32 | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.10 |
| lineBERTEnable This variable enables Bit Error Rate Testing(BERT). | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.12 |
| lineBERTPattern This variable determines BERT pattern to transmit | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.13 |
| lineBERTResult This shows the result of the BERT. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.14 |
| bERTResultClrButton This clears the result of the BERT. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.15 |
| lineConnectorType This variable indicates the connector as well
as the backcard type. 1 = T1; 2 = E1.
This field is set to unused(4) for FRSM-VHS cards. | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.2 |
| lineEnable This variable disables, enables or modifies a line
1 - disable
2 - enable
3 - modify
In FRSM-2CT3, if the DS3 line is enabled, then the DS1
channels for that line will all be aut… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.3 |
| lineType This variable indicates the variety of DS1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably car… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.4 |
| lineCoding This variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
dsx1JBZS(1): refers the… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.5 |
| lineLength This is not a standard RFC 1407 DS1 variable, it is
specific to BASIS implementation. It specifies the line length:
1 - 0 to 110 ft (T1 line only)
2 - 110 to 220 ft (T1 line only… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.6 |
| lineXmtClockSource The source of Transmit Clock.
loopTiming(1): indicates that the recovered
receive clock is used as the
transmit clock.
localTiming(2)… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.7 |
| lineLoopbackCommand This variable represents the loopback confi-
guration of the DS1 interface. Agents support-
ing read/write access should return badValue in
response to a requested loopback sta… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.8 |
| lineSendCode This variable indicates what type of code is
being sent across the DS1 interface by the dev-
ice. The values mean:
dsx1SendNoCode
sending looped or normal d… | column | Enumeration | .1.3.6.1.4.1.351.110.4.3.1.1.1.1.9 |