lineLength

CISCO-MGX82XX-DSX1-MIB · .1.3.6.1.4.1.351.110.4.3.1.1.1.1.6

Object

column r/w Enumeration

This is not a standard RFC 1407 DS1 variable, it is
specific to BASIS implementation. It specifies the line length:
1 - 0 to 110 ft (T1 line only) 
2 - 110 to 220 ft (T1 line only) 
3 - 220 to 330 ft (T1 line only) 
4 - 330 to 440 ft (T1 line only) 
5 - 440 to 550 ft (T1 line only) 
6 - 550 to 660 ft (T1 line only) 
7 - greater than 660 ft (T1 line only)
8 - 75 ohms (E1 line only (BNC))
9 - 120 ohms (E1 line only (DB-15))
              
The default value for T1 is 1, for E1, if the connector
type is DB15 then the default is 9, if BNC, it's 8.
For FRSM-2CT3, the line length of DS1 has no meaning
as there are no physical DS1 lines. So, for this
card, the value is set to notRequired (16).

Context

MIB: CISCO-MGX82XX-DSX1-MIB
OID: .1.3.6.1.4.1.351.110.4.3.1.1.1.1.6
Type: column
Access: readwrite
Status: current
Parent: dsx1CnfGrpEntry
Table: dsx1CnfGrpTable
Siblings: 14

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	lineLength0To110Feet
`2`	lineLength110To220Feet
`3`	lineLength220To330Feet
`4`	lineLength330To440Feet
`5`	lineLength440To550Feet
`6`	lineLength550To660Feet
`7`	lineLength660FeetPlus
`8`	lineLength-75-Ohm
`9`	lineLength-120-Ohm
`10`	lineLength0To131Feet
`11`	lineLength131To262Feet
`12`	lineLength262To393Feet
`13`	lineLength393To524Feet
`14`	lineLength524To655Feet
`15`	lineLength655FeetPlus
`16`	notRequired

Related Objects

Sibling Objects

Object	Type	Syntax	OID
lineNum This object is the identifier of a DS1/E1 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1/E1 interface, it should hav…	column	Integer32	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.1`
lineUsedTimeslotsBitMap Bit map of used DS0 for this line.	column	Integer32	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.10`
lineLoopbackCodeDetection Enable detection of line Loopback Codes	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.11`
lineBERTEnable This variable enables Bit Error Rate Testing(BERT).	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.12`
lineBERTPattern This variable determines BERT pattern to transmit	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.13`
lineBERTResult This shows the result of the BERT.	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.14`
bERTResultClrButton This clears the result of the BERT.	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.15`
lineConnectorType This variable indicates the connector as well as the backcard type. 1 = T1; 2 = E1. This field is set to unused(4) for FRSM-VHS cards.	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.2`
lineEnable This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify In FRSM-2CT3, if the DS3 line is enabled, then the DS1 channels for that line will all be aut…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.3`
lineType This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably car…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.4`
lineCoding This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS(1): refers the…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.5`
lineXmtClockSource The source of Transmit Clock. loopTiming(1): indicates that the recovered receive clock is used as the transmit clock. localTiming(2)…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.7`
lineLoopbackCommand This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback sta…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.8`
lineSendCode This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal d…	column	Enumeration	`.1.3.6.1.4.1.351.110.4.3.1.1.1.1.9`