cLApPrimedDiscoveryTimeout
CISCO-LWAPP-AP-MIB ·
.1.3.6.1.4.1.9.9.513.1.3.23
Object
scalar
r/w
seconds Integer32
This object specifies the primed timeout for the AP discovery.
Context
- MIB
- CISCO-LWAPP-AP-MIB
- OID
.1.3.6.1.4.1.9.9.513.1.3.23- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- ciscoLwappApGlobal
- Siblings
- 35
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: 0-0
range: 120-43200
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cLApFastHbTimerTable This table contains entries for AP fast heartbeat
timers configured in the controller. At startup,
all the entries in this table are set up by the central
controller. A managemen… | table | - | .1.3.6.1.4.1.9.9.513.1.3.1 |
| cLApGlobalFailoverPriority This object specifies the global AP failover priority.
If Enabled, Priorities will be considered of the APs which
wishes to join the controller. Preference will be given to
the … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.10 |
| cLApGlobalTcpMss This object specifies the Global AP TCP MSS value.
Permissible value are between 536 and 1363. This will
also enable the global TCP MSS flag.
Value of 0 will disable the global TC… | scalar | Integer32 | .1.3.6.1.4.1.9.9.513.1.3.11 |
| cLApGlobalDot11IfTable This table is used to configure the global dot11
parameters per slot id, represented by cLApDot11IfSlotId,
of the radio interface in all the APs joined with
the controller. | table | - | .1.3.6.1.4.1.9.9.513.1.3.12 |
| cLApGlobalEthernetIfTable This table is used to configure the global parameters
on Ethernet interfaces of all the APs joined with the
controller. | table | - | .1.3.6.1.4.1.9.9.513.1.3.13 |
| cLApGlobalRetransmitCount This object specifies the retransmission count for the
Control Packet of all the Access Points, joined to this
controller. This value specifies the number of packets
retransmitt… | scalar | retries SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.3.14 |
| cLApGlobalRetransmitTimeout This object specifies the retransmission timeout for the
Control Packet of all the Access Points, joined to this
controller. This value specifies the timeout for each
retransmis… | scalar | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.3.15 |
| cLApOeapDisableLocalAccess This object specifies whether the local access is supported for
all the Office Extended Access Points, joined to this
controller. If set to true, the local SSID and and LAN ports… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.16 |
| cLApGlobalLEDState This object specifies whether the LED state of all the access
points should be enabled or disabled. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.17 |
| cLApRadioInterfaceShutdownEnabled This object specifies to enable or disable AP radio Interface.
When enabled, AP radio's will be shut down when Ethernet link
goes down for a duration of time set for
cLApEtherne… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.18 |
| cLApEthernetInterfaceDowntime This object specifies the ethernet interface down time after
which the AP radio interface will be shut down. | scalar | Seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.3.19 |
| cLAPMulticastGroupAddressType This object specifies the AP multicast group address type. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.3.20 |
| cLAPMulticastGroupAddress This object specifies the AP multicast group address. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.3.21 |
| cLAPMulticastMode This object specifies the switch's ethernet
multicast support.
unicast - Controller will convert multicast to
unicast packet.
multicast - Multicast mode is enabled. | scalar | Enumeration | .1.3.6.1.4.1.9.9.513.1.3.22 |
| cLApGlobalPreferMode This object specifies the global capwap prefer-mode.
ipv4 - capwap tunnel established with ipv4 address.
ipv6 - capwap tunnel established with ipv6 address. | scalar | Enumeration | .1.3.6.1.4.1.9.9.513.1.3.24 |
| cLApGlobalAPLagCapability This object specifies whether the ap-lag capability state of
all the access points should be enabled or disabled.
A value of 'true' indicates ap-lag capapbility is enabled.
A valu… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.25 |
| cLApGlobalAPDtlsVersion This object specifies the dtls version of ap | scalar | Enumeration | .1.3.6.1.4.1.9.9.513.1.3.26 |
| cLApGlobalAPDtlsCipherSuite This object specifies the dtls cipher suite of ap | scalar | Enumeration | .1.3.6.1.4.1.9.9.513.1.3.27 |
| cLApGlobalMaxApsSupported This object represents the maximum number of APs supported by
this controller. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.9.513.1.3.28 |
| cLApPrimaryDiscoveryTimeout This object specifies the timeout for the primary AP
discovery. | scalar | seconds Unsigned32 | .1.3.6.1.4.1.9.9.513.1.3.3 |
| cLApAuthorizeApMacAuth This flag specifies the status of mac auth | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.30 |
| cLApAuthorizeApSerialNumAuth This flag specifies the status of serial number auth | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.31 |
| cLApAuthorizeApMethodList This object specifies the method list used for the AP
authorization when enabled.
The default method list is default | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.3.32 |
| cLApGlobalAPAuditReport This object is used to enable/disable AP audit reporting.
It is disabled by default | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.3.33 |
| cLApGlobalAPAuditReportInterval This object specifies the audit report interval in minutes.
The default interval is 1440 minutes | scalar | Minutes Unsigned32 | .1.3.6.1.4.1.9.9.513.1.3.34 |
| cLApGlobalAPConnectCount This object represents the Count of AP's that are connected
to the Controller. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.3.35 |
| cLApAuthorizeApMacMethodList This object specifies the method list used for the AP
MAC authorization when enabled. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.3.36 |
| cLApAuthorizeApSerialNumMethodList This object specifies the method list used for the AP
serial number authorization when enabled. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.3.37 |
| clApImageUpgradeConfig | node | - | .1.3.6.1.4.1.9.9.513.1.3.38 |
| cLApGlobalPrimaryControllerAddressType This object specifies the type of the primary controller's
address made available through cLApPrimaryControllerAddress. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.3.4 |
| cLApGlobalPrimaryControllerAddress This object specifies the address of the primary controller
that the APs will join. The name and address should be
provided in the same set request. An address of all zeros
will… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.3.5 |
| cLApGlobalPrimaryControllerName This object specifies the name of the primary controller
that the APs will join. | scalar | OctetString | .1.3.6.1.4.1.9.9.513.1.3.6 |
| cLApGlobalSecondaryControllerAddressType This object specifies the type of the secondary
controller's address made available through
cLApSecondaryControllerAddress. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.3.7 |
| cLApGlobalSecondaryControllerAddress This object specifies the address of the secondary
controller that the APs will join. The name and address
should be provided in the same set request. An address
of all zeros wi… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.3.8 |
| cLApGlobalSecondaryControllerName This object specifies the name of the secondary controller
that the APs will join. | scalar | OctetString | .1.3.6.1.4.1.9.9.513.1.3.9 |