ipSecPolMapAclString

CISCO-IPSEC-POLICY-MAP-MIB · .1.3.6.1.4.1.9.9.172.1.2.1.1.4
Commands MIB view Table view

Object

column SNMPv2-TCDisplayString 
The value of this object is the number or
the name of the access control string (ACL) 
that caused this IPSec tunnel to be established. 
 The ACL that causes an IPSec tunnel
 to be established is referenced by the 
 cryptomap of the tunnel.
              
 The ACL identifies the traffic that requires
 protection as defined by the policy.
              
 For instance, the ACL that requires FTP
 traffic between local subnet 172.16.14.0 and a
 remote subnet 172.16.16.0 to be protected
 is defined as
              
 ==>access-list 101 permit tcp 172.16.14.0 0.0.0.255
                  172.16.16.0 0.0.0.255 eq ftp
              
 When this command causes an IPSec tunnel to be
  established, the object 'ipSecPolMapAclString'
  assumes the string value '101'.
              
 If the ACL is a named list such as
  ==> ip access-list standard myAcl
       permit 172.16.16.8 0.0.0.0
              
 then the value of this MIB element corresponding to 
  IPSec tunnel that was created by this ACL would
  be 'myAcl'.

Context

MIB
CISCO-IPSEC-POLICY-MAP-MIB
OID
.1.3.6.1.4.1.9.9.172.1.2.1.1.4
Type
column
Access
readonly
Status
current
Parent
ipSecPolMapEntry
Groups
1

Net-SNMP examples

How SNMP and these commands work

Walk the column to discover its indexed instances, or supply every index to read one instance.

Walk the column
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-IPSEC-POLICY-MAP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-IPSEC-POLICY-MAP-MIB::ipSecPolMapAclString'
More examples
Read one indexed instance
/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'CISCO-IPSEC-POLICY-MAP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-IPSEC-POLICY-MAP-MIB::ipSecPolMapAclString.<ipSecPolMapTunIndex>'
Translate to a numeric OID
/usr/bin/snmptranslate -Pud -Ir -On -m 'CISCO-IPSEC-POLICY-MAP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'CISCO-IPSEC-POLICY-MAP-MIB::ipSecPolMapAclString'

Syntax

SNMPv2-TCDisplayString
Source
SNMPv2-TCDisplayString
Base type
OctetString
Display format
255a
Type Description
Represents textual information taken from the NVT ASCII
          
character set, as defined in pages 4, 10-11 of RFC 854.
          
To summarize RFC 854, the NVT ASCII repertoire specifies:
          
  - the use of character codes 0-127 (decimal)
          
  - the graphics characters (32-126) are interpreted as
    US ASCII
          
  - NUL, LF, CR, BEL, BS, HT, VT and FF have the special
    meanings specified in RFC 854
          
  - the other 25 codes have no standard interpretation
          
  - the sequence 'CR LF' means newline
          
  - the sequence 'CR NUL' means carriage-return
          
  - an 'LF' not preceded by a 'CR' means moving to the
    same column on the next line.
          
  - the sequence 'CR x' for any x other than LF or NUL is
    illegal.  (Note that this also means that a string may
    end with either 'CR LF' or 'CR NUL', but not with CR.)
          
Any object defined using this syntax may not exceed 255
characters in length.

Values & Constraints

Type Constraints
range: 0..255

Conformance

Member of
ipSecPhaseTwoPolMapGroup