cvdslCurrStatus

CISCO-IETF-VDSL-LINE-MIB · .1.3.6.1.4.1.9.10.87.1.1.2.1.7

Object

column Bits

Indicates current state of the Vtu line.  This is a
bit-map of possible conditions.  The various bit
positions are:
              
0   noDefect             There no defects on the line
              
1   lossOfFraming        Vtu failure due to not receiving 
                         valid frame.
              
2   lossOfSignal         Vtu failure due to not receiving 
                         signal.
              
3   lossOfPower          Vtu failure due to loss of power.
              
4   lossOfSignalQuality  Loss of Signal Quality is declared
                         when the Noise Margin falls below 
                         the Minimum Noise Margin, or the 
                         bit-error-rate exceeds 10^-7.
              
5   lossOfLink           Vtu failure due to inability to 
                         link with peer Vtu.
              
6   dataInitFailure      Vtu failure during initialization 
                         due to bit errors corrupting
                         startup exchange data.
              
7   configInitFailure    Vtu failure during initialization 
                         due to peer Vtu not able to support
                         requested configuration.
              
8   protocolInitFailure  Vtu failure during initialization 
                         due to incompatible protocol used 
                         by the peer Vtu.
              
9   noPeerVtuPresent     Vtu failure during initialization 
                         due to no activation sequence 
                         detected from peer Vtu.
              
This is intended to supplement ifOperStatus.

Context

MIB: CISCO-IETF-VDSL-LINE-MIB
OID: .1.3.6.1.4.1.9.10.87.1.1.2.1.7
Type: column
Access: readonly
Status: current
Parent: cvdslPhysEntry
Table: cvdslPhysTable
Siblings: 8

Syntax

Bits

Values & Constraints

Enumerated Values

`0`	noDefect
`1`	lossOfFraming
`2`	lossOfSignal
`3`	lossOfPower
`4`	lossOfSignalQuality
`5`	lossOfLink
`6`	dataInitFailure
`7`	configInitFailure
`8`	protocolInitFailure
`9`	noPeerVtuPresent

Related Objects

Sibling Objects

Object	Type	Syntax	OID
cvdslPhysSide Identifies whether the modem is the Vtuc or Vtur.	column	CVdslLineEntity	`.1.3.6.1.4.1.9.10.87.1.1.2.1.1`
cvdslInvSerialNumber The vendor specific string that identifies the vendor equipment.	column	OctetString	`.1.3.6.1.4.1.9.10.87.1.1.2.1.2`
cvdslInvVendorID The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.	column	OctetString	`.1.3.6.1.4.1.9.10.87.1.1.2.1.3`
cvdslInvVersionNumber The vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed a…	column	OctetString	`.1.3.6.1.4.1.9.10.87.1.1.2.1.4`
cvdslCurrSnrMgn Noise Margin as seen by this Vtu with respect to its received signal in tenth dB.	column	tenth dB Integer32	`.1.3.6.1.4.1.9.10.87.1.1.2.1.5`
cvdslCurrAtn Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu.	column	tenth dB Unsigned32	`.1.3.6.1.4.1.9.10.87.1.1.2.1.6`
cvdslCurrOutputPwr Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.	column	tenth dBm Integer32	`.1.3.6.1.4.1.9.10.87.1.1.2.1.8`
cvdslCurrAttainableRate Indicates the maximum currently attainable data rate by the Vtu. This value will be equal or greater than the current line rate.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.4.1.9.10.87.1.1.2.1.9`