cpwCTDMCfgSetUp2SynchTimeOut
CISCO-IETF-PW-TDM-MIB ·
.1.3.6.1.4.1.9.10.131.1.3.1.10
Object
The amount of time the host should wait before declaring the pseudo wire in down state, if the number of consecutive TDM packets that have been received after changing the administrative status to up and after finalization of signaling (if supported) between the two PEs is smaller than cpwCTDMCfgConsecPktsInSynch. Once the the PW has OperStatus of 'up' this parameter is no longer valid. This parameter is defined to ensure that the host does not prematurely inform failure of the PW. In particular PW 'down' notifications should not be sent before expiration of this timer. This parameter is valid only after adminisrative changes of the status of the PW. If the PW fails due to network impairments a 'down' notification should be sent.
Context
- MIB
- CISCO-IETF-PW-TDM-MIB
- OID
.1.3.6.1.4.1.9.10.131.1.3.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Units
- millisecond
- Parent
- cpwCTDMCfgEntry
- Table
- cpwCTDMCfgTable
- Siblings
- 18
Syntax
millisecond SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cpwCTDMCfgIndex Index to an entry in this table. The value is a copy of
the assigned cpwCTDMCfgIndexNext. | column | CpwTDMCfgIndex | .1.3.6.1.4.1.9.10.131.1.3.1.1 |
| cpwCTDMCfgPktReplacePolicy This parameter determines the value to be played when CE
bound packets have over/underflow the jitter buffer, or are
missing for any reason. This AIS (Alarm Indication Signal)
pat… | column | Enumeration | .1.3.6.1.4.1.9.10.131.1.3.1.11 |
| cpwCTDMCfgAvePktLossTimeWindow The length of time over which the average packet
loss rate should be computed to detect Excessive packet
loss rate | column | millisecond SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.10.131.1.3.1.12 |
| cpwCTDMCfgExcessivePktLossThreshold Excessive packet loss rate is detected by computing the
average packetloss rate over a
cpwCTDMCfgAvePktLossTimeWindow amount of time and
comparing it with this threshold value. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.13 |
| cpwCTDMCfgAlarmThreshold Alarms are only reported when the defect state persists
for the length of time specified by this object.
The object's unit is millisec | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.14 |
| cpwCTDMCfgClearAlarmThreshold Alarm MUST be cleared after the corresponding defect is
undetected for the amount of time specified by this object.
The object's unit is millisec | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.15 |
| cpwCTDMCfgMissingPktsToSes Number of missing packets detected (consecutive or not)
within a 1 second window to cause a Severely Error
Second (SES) to be counted. | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.16 |
| cpwCTDMCfgTimestampMode Timestamp generation MAY be used in one of the following
modes:
1. Absolute mode: the PSN-bound IWF sets timestamps
using the clock recovered from the incoming TDM attachment
ci… | column | Enumeration | .1.3.6.1.4.1.9.10.131.1.3.1.17 |
| cpwCTDMCfgStorageType This variable indicates the storage type for this row.
The following are the read-write objects in permanent(4)
rows, that an agent must allow to be writable:
cpwCTDMCfgPayloadSiz… | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.9.10.131.1.3.1.18 |
| cpwCTDMCfgRowStatus The status of this conceptual row.
To create a row in this table, a manager must
set this object to either createAndGo(4) or
createAndWait(5).
All of… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.10.131.1.3.1.19 |
| cpwCTDMCfgConfErr This object indicates the various configuration errors,
illegal settings within the cpwCTDMCfg table. The errors
can be due to several reasons, like Payload size mismatch
or Jitte… | column | Bits | .1.3.6.1.4.1.9.10.131.1.3.1.2 |
| cpwCTDMCfgPayloadSize The value of this object indicates the PayLoad Size (in
bytes) to be defined during the PW setUp. Upon TX,
implementation must be capable of carrying that amount of
bytes. Upon RX… | column | bytes SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.3 |
| cpwCTDMCfgPktReorder If set to true, CE bound packets are queued in the
jitter buffer, out of order packets are re-ordered. The
maximum sequence number differential (i.e., the range in
which re-sequen… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.131.1.3.1.4 |
| cpwCTDMCfgRtpHdrUsed If the value of this object is set to false, then a
RTP header is not pre-pended to the TDM packet. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.131.1.3.1.5 |
| cpwCTDMCfgJtrBfrDepth The size of this buffer SHOULD be locally
configured to allow accommodation to the PSN-specific
packet delay variation.
If configured to a value not supported by th… | column | microsecond SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.6 |
| cpwCTDMCfgPayloadSuppression This object indicates whether the Payload suppression
is eanbled or disabled.
Payload MAY be omitted in order to conserve bandwidth.
enable - Payload suppression i… | column | Enumeration | .1.3.6.1.4.1.9.10.131.1.3.1.7 |
| cpwCTDMCfgConsecPktsInSynch The number of consecutive packets with sequential
sequence numbers that are required to exit the
Loss of Packets (LOPS) state. | column | packets SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.8 |
| cpwCTDMCfgConsecMissPktsOutSynch The number of consecutive missing packets that are
required to enter the LOPS state. | column | packets SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.10.131.1.3.1.9 |