cadIfMacDomainRcpReportMode
CADANT-CMTS-LAYER2CMTS-MIB ·
.1.3.6.1.4.1.4998.1.1.20.1.4.2.1.27
Object
column
r/w
Enumeration
This attribute controls the reporting of the CM receiver profiles in the registration messages. A value of 0 means that the CM MUST NOT provide verbose reporting of all its Receive Channel Profiles. A value of 1 means that the CM MUST provide verbose reporting of Receive Channel Profiles. both standard profiles and manufacturers profiles.
Context
- MIB
- CADANT-CMTS-LAYER2CMTS-MIB
- OID
.1.3.6.1.4.1.4998.1.1.20.1.4.2.1.27- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cadIfMacDomainEntry
- Table
- cadIfMacDomainTable
- Siblings
- 48
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | nonVerbose |
1 | verbose |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cadIfMacDomainIfIndex MAC domain ifIndex | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.1 |
| cadIfMacDomainTftpEnforce Current state of TFTP enforce for this interface. | column | CadTftpEnforceType | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.10 |
| cadIfMacDomainDynamicSecret Current state of Cable Dynamic Secret for this interface. | column | CadDynamicSecretType | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.11 |
| cadIfMacDomainAnnex The value of this object indicates the conformance of
the implementation to important regional cable standards.
annexA : Annex A from ITU-J83 is used.
annexB : Annex B from ITU-J8… | column | Enumeration | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.13 |
| cadIfMacDomainMddInterval This attribute configures the interval for the insertion of MDD messages in each downstream channel of a MAC Domain. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.14 |
| cadIfMacDomainIpProvMode This attribute configures the CMTS IP provisioning mode for a MAC Domain.
When this attribute is set to 'ipv4Only' the CM will acquire a single IPv4 address
for the CM managemen… | column | Enumeration | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.16 |
| cadIfMacDomainCmStatusEvCtlEnabled If set to 'true', this attribute enables the
signaling of the CM-Status Event reporting mechanism. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.18 |
| cadIfMacDomainUsFreqRange This attribute indicates in MDD messages the
upstream frequency upper band edge of an upstream
Channel. A value 'standard' means Standard Frequency
Range and a value 'extended' me… | column | Enumeration | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.19 |
| cadIfMacDomainCapabilities Identifies the capabilities of the CMTS MAC implementation at this interface. | column | Bits | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.2 |
| cadIfMacDomainMcastDsidFwdEnabled If set to 'true', this attribute enables the
CMTS to use IP Multicast DSID Forwarding (MDF) for the MAC domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.20 |
| cadIfMacDomainDsBondingEnabled If set to 'true', this attribute enables
Downstream Channel Bonding for the MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.21 |
| cadIfMacDomainMultTxChModeEnabled If set to 'true', this attribute enables
Multiple Transmit Channel (MTC) Mode for the MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.22 |
| cadIfMacDomainEarlyAuthEncrCtrl This attribute enables or disables early
authentication and encryption (EAE) signaling for the
MAC Domain. It also defines the type of EAE
enforcement in the case that EAE is e… | column | Enumeration | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.23 |
| cadIfMacDomainTftpProxyEnabled If set to 'true', this attribute enables TFTP
Proxy functionality for the MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.24 |
| cadIfMacDomainSrcAddrVerifEnabled If set to 'true', this attribute enables Source
Address Verification (SAV) functionality for the MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.25 |
| cadIfMacDomainMulticastEncryption If set to 'true', this attribute enables multicast encryption
for all multicast flows on all downstream channels in the MAC domain
using the des56 algorithm. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.26 |
| cadIfMacDomainRegRspToOverride This attribute provides an ability to override the default value of the T6 timer in the CM.
When this attribute is not set to its default value, then the CMTS will place it into … | column | seconds Unsigned32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.28 |
| cadIfMacDomainMultRxChModeEnabled If set to true, this attribute enables Downstream Channel Bonding for the MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.29 |
| cadIfMacDomainSyncInterval Interval between CMTS transmission of successive SYNC messages at this interface. | column | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.3 |
| cadIfMacDomainCmUdcEnabled If set to true, this attribute instructs the CMTS MAC Domain to enable Upstream Drop Classifiers (UDC)
for the CMs attempting registration in this MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.30 |
| cadIfMacDomainSendUdcRulesEnabled If set to true and when the CM signals to the CMTS 'Upstream Drop Classifier Group ID encodings,
this attribute instructs the CMTS MAC Domain to send the Subscriber Management Fi… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.31 |
| cadIfMacDomainRccDynEnable This object allows user to enable or disable the autonomous creation of dynamic RCCs per mac domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.32 |
| cadIfMacDomainDsbgDynEnable This object allows user to enable or disable the autonomous creation of dynamic bonding groups per mac domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.33 |
| cadIfMacDomainDsbgReseqWaitTime Resequence wait time to se set for dynamic bonding groups per mac domain. If the value 255 indicates that requence wait time
is determined by the CMTS. | column | hundredMicroseconds Unsigned32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.34 |
| cadIfMacDomainDsbgReseqWarnThrshld Resequence warning threshold to se set for dynamic bonding groups per mac domain. If the value 255 indicates that requence
warning threshold is determined by the CMTS. | column | hundredMicroseconds Unsigned32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.35 |
| cadIfMacDomainDpId When a mac domain is created or system reset, DMM assigns a Downstream Pool ID (DPID) for each mac domain. If the value 255
indicates the DPID is invalid. | column | Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.36 |
| cadIfMacDomainUsbgDynEnable This object allows user to enable or disable the autonomous creation of dynamic upstream bonding groups per mac domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.37 |
| cadIfMacDomainDownChannelMaxFrequency This object is used to configure the C4 CMTS to accept maximum downstream
frequency limit that conform with the EuroDOCSIS specifications
(starndard range 112 MHz to 858 MHz), (ex… | column | hertz Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.38 |
| cadIfMacDomainDownChannelMinFrequency This object is used to configure the C4 CMTS to accept minimum downstream
frequency limit that conform with the EuroDOCSIS specifications
(starndard range 112 MHz to 858 MHz), (ex… | column | hertz Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.39 |
| cadIfMacDomainUcdInterval Interval between CMTS transmission of successive UCD messages for each
upstream at this interface. | column | Milliseconds Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.4 |
| cadIfMacDomainUpChannelMaxFrequency This object is used to configure the C4 CMTS to accept upstream
frequency ranges that conform with the EuroDOCSIS specifications
(5 MHz to 65 MHz), to the extended range used in J… | column | hertz Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.40 |
| cadIfMacDomainBpi2Mandatory This object determines the what minimum level of
BPI operation is required in order to allow a cable
modem to register. | column | Enumeration | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.41 |
| cadIfMacDomainDSG30Enabled If set to 'true', this attribute enables the
CMTS to use DSG3.0 on the MAC domain. If false,
then DSG reverts to the pre-DOCSIS3.0 version
without DSIDs. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.43 |
| cadIfMacDomainEnforceRulesEnabled If set to 'true', then QOS penalties as defined in the
cadEnforceRuleTable will be enforced for SFs on CMs
in this MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.44 |
| cadIfMacDomainCmTxPwrExtentionPreRegistrationEnabled Indicate if the transmit power extension (before registration) feature
is enabled or not onthe CMTS. If set to 'true', the CMTS will populate
TLV16 in the MDD message with the val… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.45 |
| cadIfMacDomainCmTxPwrExtentionPostRegistrationEnabled Indicate if the transmit power extension (after registration) feature
is enabled or not on the CMTS. If set to 'true', the CMTS will populate
TLV5.40 in the REG-RSP-MP message wit… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.46 |
| cadIfMacDomainT4TimeoutMultiplierEnabled If set to true, this attribute instructs the CMTS MAC Domain to enable the T4 Timeout
Multiplier for the CMs operating in MTCM in this MAC Domain. The multiplier will be
set equal… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.47 |
| cadIfMacDomainDynamicRccMultiTunerEnabled If set to true, this attribute instructs the CMTS MAC Domain to
enable dynamic RCC support for CM RCP's with multiple tuners. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.48 |
| cadIfMacDomainTcsSizeLimit This object is used to potentially limit the number of channels within
a CM's TCS. A value of 0 indicates the limit is determined by the CM's
capabilities, configuration and oper… | column | Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.49 |
| cadIfMacDomainMaxServiceIds Maximum number of service IDs that may be simultaneously active. | column | Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.5 |
| cadIfMacDomainDocsis31Enabled If set to true, DOCSIS 3.1 is enabled for this MAC Domain. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.50 |
| cadIfMacDomainEnergyMgt1x1Enabled This attribute indicates whether the CMTS is configured
for 1x1 Energy Management Mode of operation on a per
MAC Domain basis. If this attribute is set to 'true',
the CMTS is co… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.51 |
| cadIfMacDomainDsOfdmProfileRecoveryGuardTime The amount of time that an impaired OFDM profile will remain impaired before
transitioning to good upon being notified that the CM can decode the profile. This provides
some hy… | column | seconds Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.52 |
| cadIfMacDomainGracefulTcsReductionEnabled If set to true, the CMTS will instruct the
modem to try incrementally lower numbers of bonded
channels instead of reverting immediately to single
US bonded channel while registeri… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.53 |
| cadIfMacDomainInvitedRangingAttempts Maximum number of attempts to make on invitations for
ranging requests. A value of 0 means the system should
attempt to range forever. | column | Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.6 |
| cadIfMacDomainInsertInterval Amount of time between each broadcast station maintenance grant. | column | Centiseconds Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.7 |
| cadIfMacDomainRangingInterval Amount of time to elapse between each ranging message. | column | Centiseconds Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.8 |
| cadIfMacDomainRangeOpportunityCycle Amount of time to elapse between each ranging cycle. | column | Centiseconds Integer32 | .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.9 |