adslLineModemCapabilities
BIANCA-BRICK-ADSL-MIB ·
.0.1.1.1.1.20
Object
column
Bits
This bitfield describes which open modes ADSL modem supports: annexA : The modem supports ADSL Annex A modes annexB : The modem supports ADSL Annex B modes multimodeM : To allow additional open modes like Annex I, J, M for a bigger upstream bandwidth use multimodeM vdsl2 : Modem supports VDSL multimodeVdsl : Modem detects automatically ADSL and VDSL .
Context
- MIB
- BIANCA-BRICK-ADSL-MIB
- OID
.0.1.1.1.1.20- Type
- column
- Access
- readonly
- Status
- current
- Parent
- adslLineEntry
- Table
- adslLineTable
- Siblings
- 13
Syntax
Bits
Values & Constraints
Enumerated Values
0 | annexA |
1 | annexB |
2 | multimodeM |
3 | vdsl2 |
4 | multimodeVdsl |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adslLineIfIndex Specifies the ADSL interface index used on this line. | column | Integer32 | .0.1.1.1.1.1 |
| adslLineDyingGasp This parameter controls the behavior when the dying gasp condition
is detected. The dying gasp condition is detected when the power
input falls below a certain voltage level, eg. … | column | Enumeration | .0.1.1.1.1.10 |
| adslLineBitSwapping This parameter controls the behavior of up- and downstream bit swapping.
Setting the bit enables the bit swapping in the corresponding direction. | column | Bits | .0.1.1.1.1.11 |
| adslLineProfile This parameter adapts the training behaviour, to comply with some
special configurations used on some ADSL lines or during approval
tests of their respective ADSL providers.
The … | column | Integer32 | .0.1.1.1.1.13 |
| adslLineCodingGainOffset This parameter allows the user to control the Coding Gain
of the CPE of the modem.
The coding gain range is limited between 0dB and 7dB, a value
of -1 lets the CPE choose the co… | column | Integer32 | .0.1.1.1.1.19 |
| adslLineCoding Specifies the ADSL coding type used on this line. | column | Enumeration | .0.1.1.1.1.2 |
| adslLineOpenMode Specifies the ADSL opening mode used on this line. Possible values:
open (3): do not use adsl line,
ansiT1dot413 (5): ANSI T1.413,
gdmt (6): ADSL classic, G.DMT, ITU-T G.992.1
g… | column | Enumeration | .0.1.1.1.1.3 |
| adslLineOperationalMode Current operational mode :
unknown (1),
ansiT1dot413 (2): ANSI T1.413,
itug992dot1 (3): ADSL classic, G.DMT, ITU-T G.992.1,
itug992dot2 (4): Splitterless ADSL, ITU-T G.992.2,
adsl… | column | Enumeration | .0.1.1.1.1.4 |
| adslLineTxGainOffset This parameter allows the user to add an offset to the Tx gain
of the CPE of the modem.
The offset range is limited between -10dB and +3dB.
It is expressed in tenth dB with a gr… | column | Integer32 | .0.1.1.1.1.5 |
| adslLineRxGainOffset This parameter allows the user to add an offset to the Rx gain
of the CPE of the modem.
The offset range is limited between -5dB and +3dB.
It is expressed in tenth dB with a gra… | column | Integer32 | .0.1.1.1.1.6 |
| adslLineType This parameter indicates the adsl line type. | column | Integer32 | .0.1.1.1.1.7 |
| adslLineMarginThreshold This parameter allows the user to specify a threshold
for triggering a retrain, if the downstream margin drops
below the threshold.
The offset range is between -32dB and +31.5dB. … | column | Integer32 | .0.1.1.1.1.8 |
| adslLineAnnexType This parameter allows the user to specify the used ADSL Annex type.
annexA (1): use annex A for related adsl interface,
annexB (2): use annex B for related adsl interface. | column | Enumeration | .0.1.1.1.1.9 |