adslLineDyingGasp
BIANCA-BRICK-ADSL-MIB ·
.0.1.1.1.1.10
Object
column
r/w
Enumeration
This parameter controls the behavior when the dying gasp condition is detected. The dying gasp condition is detected when the power input falls below a certain voltage level, eg. this happens when the ATUR is switched off. If dying gasp is enabled in this case the ATUR signals the dying gasp indication to the ATUC, so the ATUC could ingore subsequent line failures (if instructed to do so) because they are consequence of the switched off power. If dying gasp is disabled nothing is signalled to the ATUC.
Context
- MIB
- BIANCA-BRICK-ADSL-MIB
- OID
.0.1.1.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adslLineEntry
- Table
- adslLineTable
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | disable |
2 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adslLineIfIndex Specifies the ADSL interface index used on this line. | column | Integer32 | .0.1.1.1.1.1 |
| adslLineBitSwapping This parameter controls the behavior of up- and downstream bit swapping.
Setting the bit enables the bit swapping in the corresponding direction. | column | Bits | .0.1.1.1.1.11 |
| adslLineProfile This parameter adapts the training behaviour, to comply with some
special configurations used on some ADSL lines or during approval
tests of their respective ADSL providers.
The … | column | Integer32 | .0.1.1.1.1.13 |
| adslLineCodingGainOffset This parameter allows the user to control the Coding Gain
of the CPE of the modem.
The coding gain range is limited between 0dB and 7dB, a value
of -1 lets the CPE choose the co… | column | Integer32 | .0.1.1.1.1.19 |
| adslLineCoding Specifies the ADSL coding type used on this line. | column | Enumeration | .0.1.1.1.1.2 |
| adslLineModemCapabilities This bitfield describes which open modes ADSL modem supports:
annexA : The modem supports ADSL Annex A modes
annexB : The modem supports ADSL Annex B modes
multi… | column | Bits | .0.1.1.1.1.20 |
| adslLineOpenMode Specifies the ADSL opening mode used on this line. Possible values:
open (3): do not use adsl line,
ansiT1dot413 (5): ANSI T1.413,
gdmt (6): ADSL classic, G.DMT, ITU-T G.992.1
g… | column | Enumeration | .0.1.1.1.1.3 |
| adslLineOperationalMode Current operational mode :
unknown (1),
ansiT1dot413 (2): ANSI T1.413,
itug992dot1 (3): ADSL classic, G.DMT, ITU-T G.992.1,
itug992dot2 (4): Splitterless ADSL, ITU-T G.992.2,
adsl… | column | Enumeration | .0.1.1.1.1.4 |
| adslLineTxGainOffset This parameter allows the user to add an offset to the Tx gain
of the CPE of the modem.
The offset range is limited between -10dB and +3dB.
It is expressed in tenth dB with a gr… | column | Integer32 | .0.1.1.1.1.5 |
| adslLineRxGainOffset This parameter allows the user to add an offset to the Rx gain
of the CPE of the modem.
The offset range is limited between -5dB and +3dB.
It is expressed in tenth dB with a gra… | column | Integer32 | .0.1.1.1.1.6 |
| adslLineType This parameter indicates the adsl line type. | column | Integer32 | .0.1.1.1.1.7 |
| adslLineMarginThreshold This parameter allows the user to specify a threshold
for triggering a retrain, if the downstream margin drops
below the threshold.
The offset range is between -32dB and +31.5dB. … | column | Integer32 | .0.1.1.1.1.8 |
| adslLineAnnexType This parameter allows the user to specify the used ADSL Annex type.
annexA (1): use annex A for related adsl interface,
annexB (2): use annex B for related adsl interface. | column | Enumeration | .0.1.1.1.1.9 |