adslAturCurrStatus

BIANCA-BRICK-ADSL-MIB · .0.1.1.3.1.7

Object

column Enumeration

Indicates mandatory state of the ATUR line, i.e. the state
of the line as seen by ATUR. 
This is a bit-map of possible conditions.  Due to the isolation
of the ATUR when line problems occur, many state
conditions like loss of power, loss of quality signal,
and initialization errors,  can not be determined.
While trouble shooting ATUR, also use object,
adslAtucCurrStatus.  The various bit positions are:
              
1      noDefect             There no defects on the line
              
2      lossOfFraming        ATUR failure due to not
			  receiving valid frame
              
3      lossOfSignal         ATUR failure due to not
			  receiving signal
              
4      lossOfPower          ATUR failure due to loss of
			  power
              
5      lossOfSignalQuality  Loss of Signal Quality is
			  declared when the Noise Margin
			  falls below the Minimum Noise
			  Margin, or the
			  bit-error-rate exceeds 10^-7.
              
6      lossOfCellDelineation      ATUR failure due
			  loss of Cell Delineation in interleaved
			  and non-interleaved mode.
              
This is intended to supplement ifOperStatus.

Context

MIB: BIANCA-BRICK-ADSL-MIB
OID: .0.1.1.3.1.7
Type: column
Access: readonly
Status: current
Parent: adslAturPhysEntry
Table: adslAturPhysTable
Siblings: 9

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	noDefect
`2`	lossOfFraming
`3`	lossOfSignal
`4`	lossOfPower
`5`	lossOfSignalQuality
`6`	lossOfCellDelineation

Related Objects

Sibling Objects

Object	Type	Syntax	OID
adslAturIfIndex Specifies the ADSL interface index.	column	Integer32	`.0.1.1.3.1.1`
adslAturCurrPowercutback Indicates the powercutback by the ATU in tenth dB.	column	Integer32	`.0.1.1.3.1.10`
adslAturInvSerialNumber The vendor specific string that identifies the vendor equipment.	column	OctetString	`.0.1.1.3.1.2`
adslAturInvVendorID The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.	column	OctetString	`.0.1.1.3.1.3`
adslAturInvVersionNumber The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed a…	column	OctetString	`.0.1.1.3.1.4`
adslAturCurrSnrMgn Noise Margin as seen by this ATU with respect to its received signal in tenth dB.	column	Integer32	`.0.1.1.3.1.5`
adslAturCurrAtn Measured difference between the total power transmitted by the peer ATU and the total power received by this ATU in tenth dB.	column	Integer32	`.0.1.1.3.1.6`
adslAturCurrOutputPwr Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence in tenth dB.	column	Integer32	`.0.1.1.3.1.8`
adslAturCurrAttainableRate Indicates the maximum mandatoryly attainable data rate by the ATU. This value will be equal or greater than the mandatory line rate.	column	Integer32	`.0.1.1.3.1.9`