adslAtucCurrStatus
BIANCA-BRICK-ADSL-MIB ·
.0.1.1.2.1.4
Object
column
Enumeration
Indicates mandatory state of the ATUC line, i.e. the state of the line
as seen by ATUC. This is a bit-map of possible conditions. The various bit
positions are:
1 noDefect There no defects on the line
2 lossOfFraming ATUC failure due to not
receiving valid frame.
3 lossOfSignal ATUC failure due to not
receiving signal.
4 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
5 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
6 lossOfLink ATUC failure due to inability
to link with ATUR.
7 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
8 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
9 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
10 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
11 lossOfCellDelineation ATUC failure due
loss of Cell Delineation in interleaved
and non-interleaved mode.
This is intended to supplement ifOperStatus.
Context
- MIB
- BIANCA-BRICK-ADSL-MIB
- OID
.0.1.1.2.1.4- Type
- column
- Access
- readonly
- Status
- current
- Parent
- adslAtucPhysEntry
- Table
- adslAtucPhysTable
- Siblings
- 8
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | noDefect |
2 | lossOfFraming |
3 | lossOfSignal |
4 | lossOfPower |
5 | lossOfSignalQuality |
6 | lossOfLink |
7 | dataInitFailure |
8 | configInitFailure |
9 | protocolInitFailure |
10 | noPeerAtuPresent |
11 | lossOfCellDelineation |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adslAtucIfIndex Specifies the ADSL interface index. | column | Integer32 | .0.1.1.2.1.1 |
| adslAtucInvVendorID The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters. | column | OctetString | .0.1.1.2.1.2 |
| adslAtucInvVersionNumber The vendor specific version number sent by this ATU
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed a… | column | OctetString | .0.1.1.2.1.3 |
| adslAtucCurrOutputPwr Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence in tenth dB. | column | Integer32 | .0.1.1.2.1.5 |
| adslAtucCurrAttainableRate Indicates the maximum mandatoryly attainable data rate
by the ATU. This value will be equal or greater than
the mandatory line rate. | column | Integer32 | .0.1.1.2.1.6 |
| adslAtucCurrSnrMgn Noise Margin as seen by this ATU with respect to its
received signal in tenth dB. | column | Integer32 | .0.1.1.2.1.7 |
| adslAtucCurrAtn Measured difference between the total power transmitted by
the peer ATU and the total power received by this ATU
in tenth dB. | column | Integer32 | .0.1.1.2.1.8 |
| adslAtucCurrPowercutback Indicates the powercutback by the ATU in tenth dB. | column | Integer32 | .0.1.1.2.1.9 |