arrisMtaDevWBSLIC
ARRIS-MTA-DEVICE-MIB ·
.1.3.6.1.4.1.4115.1.3.3.1.2.3.50
Object
scalar
r/w
Enumeration
The setting of this MIB sets the SLIC and DSP to WB mode. This MIB setting is persistent. This MIB should be set from the CM configuration file. If this MIB value is altered in the CM configuration file then the modem will reboot automatically after the change is applied. A SNMP set after provisioning will take effect after the next reboot.
Context
- MIB
- ARRIS-MTA-DEVICE-MIB
- OID
.1.3.6.1.4.1.4115.1.3.3.1.2.3.50- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- arrisMtaDevOperationalSetup
- Siblings
- 53
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| arrisMtaDevVPNomJitterBuffer Indicates the Voice Playout nominal jitter buffer. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.1 |
| arrisMtaDevOptionality | node | - | .1.3.6.1.4.1.4115.1.3.3.1.2.3.10 |
| arrisMtaDevLoopVoltageMgmt | node | - | .1.3.6.1.4.1.4115.1.3.3.1.2.3.11 |
| arrisMtaDevGainControl | node | - | .1.3.6.1.4.1.4115.1.3.3.1.2.3.12 |
| arrisMtaDevEnableIndexTenEleven This MIB object is used to enable telephone line indices ten and eleven
instead of telephone line indices nine and ten. Index ten will be the
mininum index for the MTA. The def… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.13 |
| arrisMtaDevDspCpsSetting Enable or Disable the ECAN fast constant power signal detection. A default value of
on(2) makes the echo cancellor disengage immediately when a high level constant power
signal i… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.14 |
| arrisMtaDevDiag | node | - | .1.3.6.1.4.1.4115.1.3.3.1.2.3.15 |
| arrisMtaDevVbdOverwriteLineBitmap When set, changes fax/modem jitter buffer settings for the selected line to the
VbdOverwriteJitterBuffer values entered in the config file.
(0) no line set, (0x1) line #1 set, (… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.16 |
| arrisMtaDevVbdOverwriteMinJitterBuffer When used in conjuction with arrisMtaDevVbdOverwriteLineBitmap, this value will
be used as the minimun jitter buffer setting in all modem/fax calls for the selected
lines. | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.17 |
| arrisMtaDevVbdOverwriteNomJitterBuffer When used in conjuction with arrisMtaDevVbdOverwriteLineBitmap, this value will
be used as the nominal jitter buffer setting in all modem/fax calls for the selected
lines. | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.18 |
| arrisMtaDevVbdOverwriteMaxJitterBuffer When used in conjuction with arrisMtaDevVbdOverwriteLineBitmap, this value will
be used as the maximum jitter buffer setting in all modem/fax calls for the selected
lines. | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.19 |
| arrisMtaDevVPJitterBufferMode Indicates the Voice Playout jitter buffer mode. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.2 |
| arrisMtaDevEventHideFQDNandIPAddress This MIB object is used to enable hide MTA fqdn and IP address on basic web page event log
. The default value for this MIB object is disable(0). | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.20 |
| arrisMtaDevDhcpOptionOverride Typically the value received in the DHCP OFFER should not change in the DHCP ACK. DHCP
RENEW/REBIND values should be consistent with the value received in the DHCP OFFER. This … | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.21 |
| arrisMtaDevTFTPServerAddrOverrideFQDN FQDN of the TFTP Server that holds the MTA config file. This is used to override the default
TFTP Server. This can only be used with the gupiTftpSvrOverride(11) Provisioning Metho… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4115.1.3.3.1.2.3.22 |
| arrisMtaDevDefaultReasonNoCIDName This MIB object determines what reason is sent to the CPE when the Caller ID Name is not included in the signal request.
The default value for this MIB object is 'O' for unavailab… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.23 |
| arrisMtaDevSipConfigFileURL The URL of the SIP configuration file for redownloading provisioning and
configuration parameters to this device. | scalar | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.4115.1.3.3.1.2.3.24 |
| arrisMtaDevSipDwnldConfig Enable a redownload of the SIP configuration file parameters specified via
the configuration file URL obtained in the MIB object arrisMtaDevSipConfigFileURL.
When read this MIB ob… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.25 |
| arrisMtaDevSpecialConfigurationOverrideEnable This object is used to enable proprietary features of the Arris MTA
From left to right, the specified bit indicates whether or not
the corresponding MTA feature is enabled. For… | scalar | Bits | .1.3.6.1.4.1.4115.1.3.3.1.2.3.26 |
| arrisMtaDevRtcpTosValue This value determines what value is used in the IP TOS byte for RTCP packets. | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.27 |
| arrisMtaDevAutomaticOsiDelay This MIB defines the time, in 100ms increments, to wait after a DLCX is received before determining if an automatic OSI should be generated by the MTA to force a line disconnect. … | scalar | 100 milliseconds Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.28 |
| arrisMtaDevCustomJitterBufferEnabled Enables ability to customize jitter buffer settings using the CustomMinJitterBuffer, CustomNomJitterBuffer and CustomMaxJitterBuffer
mibs. When this setting is off, the jitter bu… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.29 |
| arrisMtaDevRTPTxQueueSize Sets the RTP transmit queue size. | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.3 |
| arrisMtaDevCustomMinJitterBuffer Indicates the customized voice playout minimum jitter buffer to be used when the arrisMtaDevCustomJitterBufferEnabled is set to on.
Valid range is 5-160 in increments of 5 | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.30 |
| arrisMtaDevCustomNomJitterBuffer Indicates the customized voice playout nominal jitter buffer to be used when the arrisMtaDevCustomJitterBufferEnabled is set to on.
Valid range is 5-160 in increments of 5 | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.31 |
| arrisMtaDevCustomMaxJitterBuffer Indicates the customized voice playout maximum jitter buffer to be used when the arrisMtaDevCustomJitterBufferEnabled is set to on.
Valid range is 5-160 in increments of 5 | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.32 |
| arrisMtaDevEnableDHCPLog Used to enable/disable MTA DHCP logging. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.33 |
| arrisMtaDevEnableMGCPLog Used to enable/disable CallP Signalling logging | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.34 |
| arrisMtaDevClearDHCPLog Used to Clear the MTA DHCP Logs. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.35 |
| arrisMtaDevClearMGCPLog Used to Clear the MTA MGCP Logs. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.36 |
| arrisMtaDevTDDReportToCMS Allows configuration of whether TDD detection events are reported to CMS. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.37 |
| arrisMtaDevAutomaticCallResourceRecovery MIB defines the number of seconds to delay upon an on-hook event before detecting
that all resources acquired while a call was active need to be recovered on a line
in the IDLE st… | scalar | seconds Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.38 |
| arrisMtaDevPacketcableProvisioningFlow PacketCable simplified provisioning flow support for PC1.5 Compliance. This object
will be updated by the Provisioning Code. The following PC1.5 Compliant Provisioning
methods … | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.39 |
| arrisMtaDevEchoCancellerTailLength Indicates the length in milliseconds of the echo canceller tail. This object
is only settable during the processing of the MTA config file. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.4 |
| arrisMtaDevLevelControl | node | - | .1.3.6.1.4.1.4115.1.3.3.1.2.3.40 |
| arrisMtaDevOffHookFskDelay MIB defines the time (in milliseconds) to delay before sending the FSK to the CPE.
The delay starts upon receiving the ACK (DTMF D) from the CPE in response to the CAS tone for
… | scalar | milliseconds Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.41 |
| arrisMtaDevT38Timeout Allows configuration of the T38 timeout, during which time the audio is muted, before T38
failure events are reported to CMS. | scalar | seconds Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.42 |
| arrisMtaDevSuperG3FaxRelay Allows configuration of SuperG3 fax processing upon detection of the V21 CM or V.8 data signal.
When disabled, the MTA still detects the signaling for SuperG3 fax and the signal… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.43 |
| arrisMtaDevDTMFEndEventForceAscending Used to enable/disable RFC 2833 DTMF end event duration force ascending. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.44 |
| arrisMtaDevDspHandleBellModemTone Set the DSP to detect the Bell Modem Tone (2225kHz). The Bell Modem Tone is
frequently used by older data modems, usually in low speed setups. When this
MIB is set to enable(1… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.45 |
| arrisMtaDevDhcpSubOpt3Immediate This MIB object will control the comparison/handling of MTA DHCP Opt 122 SubOpt 3.
A value of off(1) will disable DHCP option 122 suboption 3 comparison/handling on the fly.
A val… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.46 |
| arrisMtaDevMaxCallPServiceFlows Used to limit the number of calls (service flows). Outgoing calls, incoming calls,
and conference call legs are included in this count. The EMTA ports are able to
call each othe… | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.47 |
| arrisMtaDevCmIp | node | - | .1.3.6.1.4.1.4115.1.3.3.1.2.3.48 |
| arrisMtaDevHDAudioDefaultPayloadType The setting of this MIB provisions the MTA to offer the G722 codec with the defined
static payload of (9)or a payload in the dynamic range of (96-127). This MIB setting is persist… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.49 |
| arrisMtaDevDspHandleNonPhaseReversedTone Set handling the DSP non phase reversed tone detection for modem. A value of
off(1) indicates the tone will not be handled. A default value of onECANEnable(2)
indicates the mo… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.5 |
| arrisMtaDevProvisionedCodecArray This is the list of codecs offered in the SDP as well as codecs returned in capabilities
for an AUEP response.
This MIB is only used with NCS signaling.
These are entered as a s… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4115.1.3.3.1.2.3.51 |
| arrisMtaDevHDAudioG722SampleRate This MIB controls the SampleRate advertised in the rtpmap for the HD codec G722.
The actual sample rate is 16000 however for backward compatibility with RFC 1890
the default is 80… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.52 |
| arrisMtaDevHDAudioEnable The setting of this MIB enables the MTA to support HD Audio codecs such as G722. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.53 |
| arrisMtaDevRtcpJitterDisabled The setting of this MIB disables the MTA to report the real Jitter value in the RTCP packet. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.54 |
| arrisMtaDevProvMethodIndicator Indicates the method used to provision the device. This object should only be
changed by the configuration file. The following provisioning methods are supported:
… | scalar | ArrsMtaDevProvMethod | .1.3.6.1.4.1.4115.1.3.3.1.2.3.6 |
| arrisMtaCfgRTPDynPortStart This defines the starting value for a range of ports that will be used dynamically
when sending out SIP RTP voice packets. This MIB and arrisMtaCfgRTPDynPortEnd
are to be used t… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.7 |
| arrisMtaCfgRTPDynPortEnd This defines the starting value for a range of ports that will be used dynamically
when sending out SIP RTP voice packets. This MIB and arrisMtaCfgRTPDynPortStart
are to be used… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4115.1.3.3.1.2.3.8 |
| arrisMtaDevVPMaxJitterBuffer Indicates the Voice Playout maximum jitter buffer. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.3.1.2.3.9 |