arrisCmDoc30SetupExtendedUpstreamTransmitPowerValue
ARRIS-CM-DOC30-DEVICE-MIB ·
.1.3.6.1.4.1.4115.1.3.4.1.3.32
Object
scalar
r/w
Integer32
When enabled, extended upstream transmit power capabilities will be reported in REG-REQ-MP
message. Setting to 0 disables this functionality. Setting to nonzero controls what Pmax
the modem advertises in 0.25dB steps. The default value is hardware-specific.
It is not recommended to change from default values. Exceeding the capabilities of the upstream
amplifier may introduce distortions and spurs which may decrease SNR of this upstream channel and
adjacent upstream channels. Please refer to the Firmware Guide and take care when setting this value.
Context
- MIB
- ARRIS-CM-DOC30-DEVICE-MIB
- OID
.1.3.6.1.4.1.4115.1.3.4.1.3.32- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- arrisCmDoc30Setup
- Siblings
- 39
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-0
range: 205-244
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| arrisCmDoc30SetupDsBonding This MIB is used to enable/disable downstream channel bonding. Changes take effect at the next
reboot. This MIB should only be set from the CM configuration file. If this MIB val… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.1 |
| arrisCmDoc30SetupUdcAllowed This object is used to disallow upstream drop classifiers, overriding the REG-RSP value.
0 = disallow UDC, regardless of what the CMTS sets
1 = allow UDC | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.10 |
| arrisCmDoc30SetupTODTimeOffset This mib is used to update CM TOD time offset.
The range of the offset is -12*60*60(-43200) to 13*60*60(46800) in seconds.
13 is Daylight Savings Time in the +12 time zone). The … | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.4.1.3.11 |
| arrisCmDoc30SetupDhcpRetries DHCP Retries during provisioning. This MIB object controls the number of times
the MTA will ignore the received, non-Secure (Basic or Hybrid) DHCP OFFER while
waiting for a Sec… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.12 |
| arrisCmDoc30SetupInvertMulticolorLEDs This MIB is used to enable/disable inverted multicolor LED behavior.
The value will be stored to NonVolatile memory(NVM) and will persist across reboots.
0 = Original LED col… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.13 |
| arrisCmDoc30SetupTurboDoxEnable This object is used to enable/disable TurboDox operation.
Set to true(1) to enable TurboDox operation mode.
Set to false(2) to disable TurboDox operation mode. This
object can on… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.4.1.3.14 |
| arrisCmDoc30SetupMdfSupportOverride This object is used to override MDF Support in CMTS REG-RSP value and disabling MDF Support.
0 = disable, use value CMTS sets
1 = enable, force MDF Support to be disabled | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.15 |
| arrisCmDoc30SetupAdvancedWebPageAccess This object is used to enable/disable access to the Advanced web page.
To disable all access set value to (0)
To enable LAN access set value to (1)
To enable WAN access set v… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.16 |
| arrisCmDoc30SetupReducedOORThreshold This mib controls the number Out-Of-Range packets the modem wiil discard and the
minimum time it will wait before it re-syncs the 'Next Expected Packet Sequence
Number' with the C… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.17 |
| arrisCmDoc30SetupPowerSaveMode This mib controls the method used for power save mode.
When set to reinitmac, PowerSaveMode will trigger a mac reinit to 1x1 unbonded,
and exit from PowerSaveMode will trigger an… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.18 |
| arrisCmDoc30SetupPowerSaveOption When set to maxbattery, the modem will be configured to maximize battery hold
up time during AC power failure. In this mode the modem will not support
synchronous upstreams, such… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.19 |
| arrisCmDoc30SetupPacketProcessorEnable Used to turn on/off the modem's packet processor. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.2 |
| arrisCmDoc30SetupKeepCpeOnIfDisconnect When enabled, the CPE mac address will remain in the cpe table when the interface
is disconnected. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.20 |
| arrisCmDoc30Spectrum | node | - | .1.3.6.1.4.1.4115.1.3.4.1.3.209 |
| arrisCmDoc30SetupPowerSaveWifiShutdownOnly When enabled, Gateway products will not power down the entire gateway, but
just the WiFi radio. This will allow the wired ethernet to remain active.
When disabled (default), the … | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.21 |
| arrisCmDoc30SetupTODSyncTimeout This value determines the interval between the TOD sync operations.
Range is 0-4320 hours, where 0 disables the sync completely.
This value sets the interval starting from the set… | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.4115.1.3.4.1.3.22 |
| arrisCmDoc30SetupSWDLFilenameCheckOverride This MIB when enabled will allow the modem to accept and download a new image that
has the same filename as the previous download. By default this MIB is disabled
to prevent an a… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.23 |
| arrisCmDoc30SetupEthernetLinkBounce This MIB when enabled will add an additional step to the T4 DOCSIS MAC reinitialization sequence.
In addition to the normal DOCSIS MAC reinitilization, this MIB will force the mod… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.24 |
| arrisCmDoc30SetupIgnoreMddSymbolClockIndicator When enabled, the cable modem will ignore the Symbol Clock Locking Indicator TLV in the MDD message and
always use asynchronous timing mode. In this mode, the cable modem will no… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.25 |
| arrisCmDoc30SetupL2VPNPromiscuousMode Set to true(1) to enable L2VPN promiscuous mode. When in promiscuous mode all
upstream and downstream L2VPN traffic will be bridged by the CM regardless of source or
destination … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.4.1.3.27 |
| arrisCmDoc30SetupTftpBlkSize This object is used for the TFTP Blocksize Option (RFC 2348).
Valid values range between 64 and 65464 octets, inclusive.
If this object is set to 0,default block size of 1428 for … | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.4.1.3.28 |
| arrisCmDoc30SetupTftpTimeout This object is used for the TFTP Timeout Option (RFC 2349).
Valid values range between 1 and 255, inclusive.
Setting this object to 0(default) disables this option.
When the smart… | scalar | Integer32 | .1.3.6.1.4.1.4115.1.3.4.1.3.29 |
| arrisCmDoc30SetupMultiColorLedBitmap Bitmap used to turn on/off the modem's multi-color LED functionality. A value of 1 enables the
multi-color functionality and a value of 0 disables it.
0x1 Link LED
0x… | scalar | Unsigned32 | .1.3.6.1.4.1.4115.1.3.4.1.3.3 |
| arrisCmDoc30SetupExtendSwCurrentVersEnable When enabled, the Firmware version displayed in the MIB docsDevSwCurrentVers will be in the format of '<eMTA Model>-<firmware version>'.
If disabled, the MIB docsDevSwCurrentVers… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.30 |
| arrisCmDoc30SetupT4timeoutRebootEnable This object is used to enable/disable unit reboot upon T4 timeout.
If it is set true(1), unit will reboot upon receipt of a T4 message.
If it is set false (2), this feature is dis… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.4.1.3.31 |
| arrisCmDoc30SetupRCPBypass This object is used to enable/disable RCP check bypass feature.
If it is set to disable (0), RCP check bypass feature is disabled.
If it is set to enable (1), RCP check bypass fea… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.33 |
| arrisCmDoc30Setup6rdPPSupport This object is used to enable/disable 6RD (protocol 41) PP support.
If it is set true(1), unit will allow 6RD (protocol 41)
packet passing through the packet processor.
If it is … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4115.1.3.4.1.3.34 |
| arrisCmDoc30SetupT4EvCtrl When an upstream is impaired, no ranging opportunities are provided for that
upstream channel, modem would send the T4 timeout every 30s. In this situation,
there will be excess… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.35 |
| arrisCmDoc30SetupExpandedBondingKey This mib is used to set a key that enables bonding additional DS channels for certain modem models.
When the value in the CM configuration file contains a valid license key, the C… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4115.1.3.4.1.3.36 |
| arrisCmDoc30BondingModeCapability This mib shows the number of downstream channels the modem is capable of bonding for certain modem type.
If arrisCmDoc30SetupExpandedBondingKey is absent or invalid, and modem sup… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.4115.1.3.4.1.3.37 |
| arrisCmDoc30SetupIgnoreMtaDnsRDValidation When enabled, the device's MTA provisioning subsystem will ignore the validation of the RD flag in the DNS response.
Value is not persistent and must be in CM config file. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.38 |
| arrisCmDoc30SetupTimeoffsetWrapper This object is used to enable/disable Timeoffset Wrapper feature.
If it is set to disable (0), Timeoffset Wrapper feature is disabled.
If it is set to enable (1), Timeoffset Wrapp… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.39 |
| arrisCmDoc30SetupSecDsLossReinitEnable This MIB when enabled allows an outage of a bonded downstream secondary channel to force
a reinitialization to occur that makes the DOCSIS modem re-register. This feature may
pr… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.4 |
| arrisCmDoc30SetupDownstreamScanMaskEnable This object is just available for CM820B/AU product to enable/disable CM downstream scan mask. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.40 |
| arrisCmDoc30SetupPartServiceFallback20 This MIB when enabled prevents the REG-ACK message from sending up a partial services
confirmation code and instead will reinitialize the primary downstream DOCSIS MAC
and force t… | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.5 |
| arrisCmDoc30SetupDSTPolicy This object is used to get and set the daylight saving time policy. This parameter
is a rule with two fields separated by semicolon (;) as shown below:
start=<start-time>;end=<end… | scalar | OctetString | .1.3.6.1.4.1.4115.1.3.4.1.3.6 |
| arrisCmDoc30SetupMddIpModeOverride This object is used to override the IP Mode TLV in the MDD message.
0 = use the MDD value
1 = IPv4 Only
2 = IPv6 Only
3 = Alternate (APM)
4 = Dual-stack (DPM) | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.7 |
| arrisCmDoc30SetupPacketCableRegion This MIB is used to set the desired region for MTA PacketCable provisioning. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.8 |
| arrisCmDoc30SetupTodDelaySecProv This MIB is used to delay secure provisioning when time-of-day retrieval fails. | scalar | Enumeration | .1.3.6.1.4.1.4115.1.3.4.1.3.9 |