issAclL3FilterInPortList
ARICENT-ISS-ACL-MIB ·
.1.3.6.1.4.1.29601.2.21.3.1.1.15
Object
column
r/w
PortList
This object specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the In port list is '0', the filter rule will not be installed in hardware. By default inport list is maintained as '0'.
Context
- MIB
- ARICENT-ISS-ACL-MIB
- OID
.1.3.6.1.4.1.29601.2.21.3.1.1.15- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- issAclL3FilterEntry
- Table
- issAclL3FilterTable
- Siblings
- 29
Syntax
PortList
- Source
- PortList
- Base type
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| issAclL3FilterNo L3 Filter rule number. | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.1 |
| issAclL3FilterSrcIpAddrPrefixLength This object specifies the length of the CIDR Prefix carried in
issAclL3FilterSrcIpAddr. In IPv4 addresses, a length of 0
indicates a match of any address; a length of 32 indicates… | column | bits INET-ADDRESS-MIBInetAddressPrefixLength | .1.3.6.1.4.1.29601.2.21.3.1.1.10 |
| issAclL3FilterMinDstProtPort This object specifies the minimum port in the destination port range. Please note
these ports are the TCP / UDP ports. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.29601.2.21.3.1.1.11 |
| issAclL3FilterMaxDstProtPort This object specifies the maximum port in the destination port range. Please note
these ports are the TCP / UDP ports. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.29601.2.21.3.1.1.12 |
| issAclL3FilterMinSrcProtPort This object specifies the minimum port in the source port range. Please note
these ports are the TCP / UDP ports. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.29601.2.21.3.1.1.13 |
| issAclL3FilterMaxSrcProtPort This object specifies the maximum port in the source port range. Please note
these ports are the TCP / UDP ports. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.29601.2.21.3.1.1.14 |
| issAclL3FilterOutPortList This object specifies the complete set of ports over which if the packet goes out,
this filter rule will be applicable.
If the outgoing port list is '0', the filter rule is appli… | column | PortList | .1.3.6.1.4.1.29601.2.21.3.1.1.16 |
| issAclL3FilterAckBit This object specifies the TCP ACK bit to be checked against the packet. The default
value is 'any'(3). It means that ACK bit will not be checked to decide the action. | column | Enumeration | .1.3.6.1.4.1.29601.2.21.3.1.1.17 |
| issAclL3FilterRstBit This object specifies the TCP RST bit to be checked against the packet. The default
value is 'any'(3). It means that RST bit will not be checked to
decide the action. | column | Enumeration | .1.3.6.1.4.1.29601.2.21.3.1.1.18 |
| issAclL3FilterTos This object specifies that the IP TOS bit to be checked against the packet. This is a
single byte integer of which the last three bits (least
significant bits) indicate Delay, T… | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.19 |
| issAclL3FilterPriority This object specifies that the priority of the filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> … | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.2 |
| issAclL3FilterDscp This object specifies that the IP Dscp value to be checked against the packet.
A value of '-1' means, the Dscp Field becomes dont care. | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.20 |
| issAclL3FilterDirection This object specifies the direction of this filter to be applied. By Default the
filter will be applied on ingress direction.
When the direction of this filter is 'in', It is appl… | column | Enumeration | .1.3.6.1.4.1.29601.2.21.3.1.1.21 |
| issAclL3FilterAction This object specifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be sent to the
ports in 'out port l… | column | Enumeration | .1.3.6.1.4.1.29601.2.21.3.1.1.22 |
| issAclL3FilterMatchCount This object specifies the number of times this filter is matched. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.29601.2.21.3.1.1.23 |
| issAclL3FilterFlowId This object specifies the flow identifier in an IPv6 header. | column | Unsigned32 | .1.3.6.1.4.1.29601.2.21.3.1.1.24 |
| issAclL3FilterStatus This object specifies the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of th… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.29601.2.21.3.1.1.25 |
| issAclL3FilterSubAction This object specifies the action that is to be taken on the incoming packet
value specified by this object is detailed below -
none - no action
modifyVlan - Traffic matching A… | column | Enumeration | .1.3.6.1.4.1.29601.2.21.3.1.1.26 |
| issAclL3FilterSubActionId This object specifies the Id to be used if the object as specified by
issAcl3FilterSubAction is either modifyvlan or nestedvlan only.
Non-Zero value need to be specify when issA… | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.27 |
| issAclL3FilterRedirectId This object specifies the redirect index associated with L3Filter entry. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.29601.2.21.3.1.1.28 |
| issAclL3FilterRestore This object is used to store the order of PCL index while storing
the configurations. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.29601.2.21.3.1.1.29 |
| issAclL3FilterProtocol This object specifies the type of protocol to be checked against the packet. The
default value is 255. If the value is 255, it means that the
protocol type can be anything and it … | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.3 |
| issAclL3FilterSynBit This object specifies the SYN RST bit to be checked against the packet. The default
value is 'any'(3). It means that SYN bit will not be checked to
decide the action. | column | Enumeration | .1.3.6.1.4.1.29601.2.21.3.1.1.30 |
| issAclL3FilterMessageType This object specifies the message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action… | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.4 |
| issAclL3FilterMessageCode This object specifies the message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action… | column | Integer32 | .1.3.6.1.4.1.29601.2.21.3.1.1.5 |
| issAclL3FilteAddrType This object specifies the type of IP address used by this classifier entry. While
other types of addresses are defined in the InetAddressType
textual convention, and DNS names, a … | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.29601.2.21.3.1.1.6 |
| issAclL3FilterDstIpAddr This object specifies the IP address to match against the packet's destination IP
address. This may not be a DNS name, but may be an IPv4 or IPv6
prefix. issAclL3FilterDstIpAddrP… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.29601.2.21.3.1.1.7 |
| issAclL3FilterSrcIpAddr This object specifies the IP address to match against the packet's source IP address.
This may not be a DNS name, but may be an IPv4 or IPv6 prefix.
issAclL3FilterSrcIpAddrPrefixL… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.29601.2.21.3.1.1.8 |
| issAclL3FilterDstIpAddrPrefixLength This object specifies the length of the CIDR Prefix carried in
issAclL3FilterDstIpAddr. In IPv4 addresses, a length of 0
indicates a match of any address; a length of 32 indicates… | column | bits INET-ADDRESS-MIBInetAddressPrefixLength | .1.3.6.1.4.1.29601.2.21.3.1.1.9 |