ARICENT-ISS-ACL-MIB Table View

This object specifies a table to control the rate limiting parameters 
either for the entire switch or for each interface in the switch.

issAclRateCtrlEntry row .1.3.6.1.4.1.29601.2.21.1.1.1

This object specifies an entry which appears in this table for each physical
interface in the switch.

Indexes

issAclRateCtrlIndex

Column	Syntax	OID
issAclRateCtrlIndex This object specifies the interface index for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.29601.2.21.1.1.1.1
issAclRateCtrlDLFLimitValue This object is used to configure the limiting value for the maximum number of dlf packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Destina…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.29601.2.21.1.1.1.2
issAclRateCtrlBCASTLimitValue This object is used to configure the limiting value for the maximum number of broadcast packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.29601.2.21.1.1.1.3
issAclRateCtrlMCASTLimitValue This object is used to configure the limiting value for the maximum number of multicast packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.29601.2.21.1.1.1.4
issAclRateCtrlPortRateLimit This object is used to configure interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.29601.2.21.1.1.1.5
issAclRateCtrlPortBurstSize this object is used to configure interface Burst Pkt Rate. (Packet Burst that can be transferred on a port at a particular second) This object's value will take effect on the interface speed. Based on the…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.29601.2.21.1.1.1.6

This object specifies the table which is used to configure L2 filter rules in the system.

issAclL2FilterEntry row .1.3.6.1.4.1.29601.2.21.2.1.1

This object specifies that each entry in this table is a L2 filter rule.
Index to the table is the L2 filter number.

Indexes

issAclL2FilterNo

Column	Syntax	OID
issAclL2FilterNo This object specifies the L2 Filter rule number.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.29601.2.21.2.1.1.1
issAclL2FilterPriority This object specifies the priority of the L2 filter can be used to decide which filter rule is applicable when --> the packet matches with more than one filter rules --> All the filter rules result in 'allow'ing …	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.29601.2.21.2.1.1.2
issAclL2FilterEtherType This object specifies the value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '0'. When this object is SET with the default value, frames are not match…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.29601.2.21.2.1.1.3
issAclL2FilterProtocolType This object specifies the non IP protocol type to be filtered. aarp | amber | dec-spanning | decnet-iv | diagnostic | dsm |etype-6000 | etype-8042 | lat | lavc-sca | mop-console | mop-dump | msdos | mumps | netbios |…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.29601.2.21.2.1.1.4
issAclL2FilterDstMacAddr This object specifies that the Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont care condition ie) any Dst Mac Address .	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.29601.2.21.2.1.1.5
issAclL2FilterSrcMacAddr This object specifies that the Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care condition ie) any Src Mac address	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.29601.2.21.2.1.1.6
issAclL2FilterVlanId This object specifies that the Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. A value of '0' means, this object is unused. Configuring this value is not allowed.	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.29601.2.21.2.1.1.7
issAclL2FilterInPortList This object specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. If the In port list is '0', the filter rule will not be installed in hardware. Even though the…	PortListr/w	.1.3.6.1.4.1.29601.2.21.2.1.1.8
issAclL2FilterAction This object specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will b…	Enumerationr/w Enumerated Values: 1 allow 2 drop 3 redirect	.1.3.6.1.4.1.29601.2.21.2.1.1.9
issAclL2FilterMatchCount This object specifies the number of times this filter is matched.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.2.1.1.10
issAclL2FilterStatus This object specifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.29601.2.21.2.1.1.11
issAclL2FilterOutPortList This object specifies the complete set of ports over which this filter is applied for packets egress at Ports in this list. If the Out port list is '0', the filter rule is applicable for the outgoing packets on all po…	PortListr/w	.1.3.6.1.4.1.29601.2.21.2.1.1.12
issAclL2FilterDirection This object specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It is applied on specified ports of the issAclL2Fi…	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.29601.2.21.2.1.1.13
issAclL2FilterSubAction This object specifies that the action to be taken on the incoming packet is detailed below - none - no action modifyVlan - Traffic matching ACL rule will have VLAN ID classified/modified to value speci…	Enumerationr/w Enumerated Values: 0 none 1 modifyVlan 2 nestedVlan 3 stripOuterHdr 4 modifyDP 5 modifyTC 6 modifyCfiDei	.1.3.6.1.4.1.29601.2.21.2.1.1.14
issAclL2FilterSubActionId This object specifies that the Id to be used if the object as specified by issAclL2FilterSubAction is either modifyvlan or nestedvlan only. Non-Zero value need to be specify when issAclL2FilterSubAction is modify or Ne…	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.29601.2.21.2.1.1.15
issAclL2FilterRedirectId This object specifies the redirect index associated with L2Filter entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.29601.2.21.2.1.1.16
issAclL2NextFilterNo This object specifies that the Next Filter rule number to be matched for traffic matching the current ACL rule	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.29601.2.21.2.1.1.17
issAclL2NextFilterType This object specifies the type of the next access-control list. The type could take the value 'l2filter' for MAC-based ACLs and 'l3filter' for IP-based ACLs. It takes the value 'userdefined' for filtering based on use…	Enumerationr/w Enumerated Values: 0 l2filter 1 l3filter 2 userdefined	.1.3.6.1.4.1.29601.2.21.2.1.1.18
issAclL2FilterCfiDeiBit This object specifies the CfiDei bit value in the c-vlan tag or s-vlan tag of the packet to be applied in the filter.	Enumerationr/w Enumerated Values: 1 set 2 reset	.1.3.6.1.4.1.29601.2.21.2.1.1.19
issAclL2FilterDP This object specifies the drop precedence level to be applied in the filter.	Enumerationr/w Enumerated Values: 1 green 2 yellow 3 red	.1.3.6.1.4.1.29601.2.21.2.1.1.20
issAclL2FilterRestore This object stores the order of PCL index while storing the configurations.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.29601.2.21.2.1.1.21
issAclL2FilterDstMacAddrMask This object specifies that the mask used to match the Destination MAC address with the packet. By Default, the Destination Mac Address Mask will be ff:ff:ff:ff:ff:ff which means macth exactly the Src Mac specified add…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.29601.2.21.2.1.1.22
issAclL2FilterSrcMacAddrMask This object specifies that the mask used to match the Source MAC address with the packet. By Default, the Source Mac Address Mask will be ff:ff:ff:ff:ff:ff which means macth exactly the Src Mac specified address	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.29601.2.21.2.1.1.23

This object specifies a table to configure L3 filter rules in the system.

issAclL3FilterEntry row .1.3.6.1.4.1.29601.2.21.3.1.1

This object specifies that each entry in this table is a L3 filter rule.
Index to the table is L3 filter number.

Indexes

issAclL3FilterNo

Column	Syntax	OID
issAclL3FilterNo L3 Filter rule number.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.29601.2.21.3.1.1.1
issAclL3FilterPriority This object specifies that the priority of the filter can be used to decide which filter rule is applicable when --> the packet matches with more than one filter rules --> All the filter rules result in 'allow'in…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.29601.2.21.3.1.1.2
issAclL3FilterProtocol This object specifies the type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it will not be checked to decide the actio…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.29601.2.21.3.1.1.3
issAclL3FilterMessageType This object specifies the message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in issAclL3FilterAction. The defaul…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.29601.2.21.3.1.1.4
issAclL3FilterMessageCode This object specifies the message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in issAclL3FilterAction. The defaul…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.29601.2.21.3.1.1.5
issAclL3FilteAddrType This object specifies the type of IP address used by this classifier entry. While other types of addresses are defined in the InetAddressType textual convention, and DNS names, a classifier can only look at packets on t…	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.29601.2.21.3.1.1.6
issAclL3FilterDstIpAddr This object specifies the IP address to match against the packet's destination IP address. This may not be a DNS name, but may be an IPv4 or IPv6 prefix. issAclL3FilterDstIpAddrPrefixLength indicates the number of bits…	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.29601.2.21.3.1.1.7
issAclL3FilterSrcIpAddr This object specifies the IP address to match against the packet's source IP address. This may not be a DNS name, but may be an IPv4 or IPv6 prefix. issAclL3FilterSrcIpAddrPrefixLength indicates the number of bits that …	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.29601.2.21.3.1.1.8
issAclL3FilterDstIpAddrPrefixLength This object specifies the length of the CIDR Prefix carried in issAclL3FilterDstIpAddr. In IPv4 addresses, a length of 0 indicates a match of any address; a length of 32 indicates a match of a single host address, and a…	bitsINET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.4.1.29601.2.21.3.1.1.9
issAclL3FilterSrcIpAddrPrefixLength This object specifies the length of the CIDR Prefix carried in issAclL3FilterSrcIpAddr. In IPv4 addresses, a length of 0 indicates a match of any address; a length of 32 indicates a match of a single host address, and a…	bitsINET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.4.1.29601.2.21.3.1.1.10
issAclL3FilterMinDstProtPort This object specifies the minimum port in the destination port range. Please note these ports are the TCP / UDP ports.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.3.1.1.11
issAclL3FilterMaxDstProtPort This object specifies the maximum port in the destination port range. Please note these ports are the TCP / UDP ports.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.3.1.1.12
issAclL3FilterMinSrcProtPort This object specifies the minimum port in the source port range. Please note these ports are the TCP / UDP ports.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.3.1.1.13
issAclL3FilterMaxSrcProtPort This object specifies the maximum port in the source port range. Please note these ports are the TCP / UDP ports.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.3.1.1.14
issAclL3FilterInPortList This object specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the In port list is '0', the filter rule will not be installed in hardware. By default inport lis…	PortListr/w	.1.3.6.1.4.1.29601.2.21.3.1.1.15
issAclL3FilterOutPortList This object specifies the complete set of ports over which if the packet goes out, this filter rule will be applicable. If the outgoing port list is '0', the filter rule is applicable for all the outgoing packets in a…	PortListr/w	.1.3.6.1.4.1.29601.2.21.3.1.1.16
issAclL3FilterAckBit This object specifies the TCP ACK bit to be checked against the packet. The default value is 'any'(3). It means that ACK bit will not be checked to decide the action.	Enumerationr/w Enumerated Values: 1 establish 2 notEstablish 3 any	.1.3.6.1.4.1.29601.2.21.3.1.1.17
issAclL3FilterRstBit This object specifies the TCP RST bit to be checked against the packet. The default value is 'any'(3). It means that RST bit will not be checked to decide the action.	Enumerationr/w Enumerated Values: 1 set 2 notSet 3 any	.1.3.6.1.4.1.29601.2.21.3.1.1.18
issAclL3FilterTos This object specifies that the IP TOS bit to be checked against the packet. This is a single byte integer of which the last three bits (least significant bits) indicate Delay, Throughput and Reliability i.e 'uuuuudtr…	Integer32r/w Constraints: range: -1-7	.1.3.6.1.4.1.29601.2.21.3.1.1.19
issAclL3FilterDscp This object specifies that the IP Dscp value to be checked against the packet. A value of '-1' means, the Dscp Field becomes dont care.	Integer32r/w Constraints: range: -1-63	.1.3.6.1.4.1.29601.2.21.3.1.1.20
issAclL3FilterDirection This object specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It is applied on specified ports of the issAclL3Fi…	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.29601.2.21.3.1.1.21
issAclL3FilterAction This object specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be sent to the ports in 'out port list'. If the out port list is '0', the …	Enumerationr/w Enumerated Values: 1 allow 2 drop 3 redirect	.1.3.6.1.4.1.29601.2.21.3.1.1.22
issAclL3FilterMatchCount This object specifies the number of times this filter is matched.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.3.1.1.23
issAclL3FilterFlowId This object specifies the flow identifier in an IPv6 header.	Unsigned32r/w Constraints: range: 0-1048575	.1.3.6.1.4.1.29601.2.21.3.1.1.24
issAclL3FilterStatus This object specifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.29601.2.21.3.1.1.25
issAclL3FilterSubAction This object specifies the action that is to be taken on the incoming packet value specified by this object is detailed below - none - no action modifyVlan - Traffic matching ACL rule will have VLAN ID classified/mod…	Enumerationr/w Enumerated Values: 0 none 1 modifyVlan 2 nestedVlan	.1.3.6.1.4.1.29601.2.21.3.1.1.26
issAclL3FilterSubActionId This object specifies the Id to be used if the object as specified by issAcl3FilterSubAction is either modifyvlan or nestedvlan only. Non-Zero value need to be specify when issAclL3FilterSubAction is modify or Nested …	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.29601.2.21.3.1.1.27
issAclL3FilterRedirectId This object specifies the redirect index associated with L3Filter entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.29601.2.21.3.1.1.28
issAclL3FilterRestore This object is used to store the order of PCL index while storing the configurations.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.29601.2.21.3.1.1.29
issAclL3FilterSynBit This object specifies the SYN RST bit to be checked against the packet. The default value is 'any'(3). It means that SYN bit will not be checked to decide the action.	Enumerationr/w Enumerated Values: 1 set 2 notSet 3 any	.1.3.6.1.4.1.29601.2.21.3.1.1.30

This object specifies the table which is used to configure user defined filter rules in the system.
This table is used for specifying the user defined packet header elements for application of filter rules.
This table could also be used for supporting AND, OR,NOT operations on existing filter rules and deriving
new user defined ACL rules.

issAclUserDefinedFilterEntry row .1.3.6.1.4.1.29601.2.21.4.1.1

This object specifies the user defined filter entry indexed uniquely by issAclUserDefinedFilterId.

Indexes

issAclUserDefinedFilterId

Column	Syntax	OID
issAclUserDefinedFilterId This object specifies an Index to uniquely identify the User defined filter table entry.	IndexInteger Type Constraints: range: 1..65535	.1.3.6.1.4.1.29601.2.21.4.1.1.1
issAclUserDefinedFilterPktType This object specifies the type of packet for which packet-filter match needs to be applied on incoming traffic.	Enumerationr/w Enumerated Values: 0 userDef 1 ethernet 2 ipv4 3 ipv6 4 ipv4tcp 5 ipv6tcp 6 ipv4udp 7 ipv6udp 8 mpls 9 fragip	.1.3.6.1.4.1.29601.2.21.4.1.1.2
issAclUserDefinedFilterOffSetBase This object specifies the offset base from the start of packet header ( beginning of full packet) for which the match needs to be applied on incoming traffic. A value of 0 indicates Start of L2 Header, value 1 indicate…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.29601.2.21.4.1.1.3
issAclUserDefinedFilterOffSetValue This object specifies the offset value for which packet-filter match needs to be applied on incoming traffic. A value of zero indicates that this field is dont-care. The offset value is a contiguous set of 128 bytes fro…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.29601.2.21.4.1.1.4
issAclUserDefinedFilterOffSetMask This object specifies the mask for the offset value. The actual user defined value to be used for matching incoming traffic is obtained after ANDing the OffsetValue and OffsetMask. A value of 0 indicates that this field…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.29601.2.21.4.1.1.5
issAclUserDefinedFilterPriority This object specifies the priority of the filter that can be used to decide which filter rule is applicable when --> the packet matches with more than one filter rules --> All the filter rules result in 'allow'in…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.29601.2.21.4.1.1.6
issAclUserDefinedFilterAction Action value allow/drop/redirect specify the action to be taken on the packet if the filter rule matches. --> If the action is 'allow', the packet will be sent to the ports as specified by issRedirectInterfaceGr…	Enumerationr/w Enumerated Values: 1 allow 2 drop 3 redirect 4 and 5 or 6 not	.1.3.6.1.4.1.29601.2.21.4.1.1.7
issAclUserDefinedFilterInPortList This object specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. Filter will be applied in chip when port list is not null. If the In port list is '0', the fil…	PortListr/w	.1.3.6.1.4.1.29601.2.21.4.1.1.8
issAclUserDefinedFilterIdOneType This Object specifies the type of the Base ACL rule 1 that is used for deriving new ACL rule.	Enumerationr/w Enumerated Values: 1 macbased 2 ipbased	.1.3.6.1.4.1.29601.2.21.4.1.1.9
issAclUserDefinedFilterIdOne This Object specifies the ID of the Base ACL rule 1 (MAC-based or IP-based) that is used for deriving new ACL rule.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.29601.2.21.4.1.1.10
issAclUserDefinedFilterIdTwoType This Object specifies the type of the Base ACL rule 2 that is used for deriving new ACL rule.	Enumerationr/w Enumerated Values: 1 macbased 2 ipbased	.1.3.6.1.4.1.29601.2.21.4.1.1.11
issAclUserDefinedFilterIdTwo This Object specifies the ID of the Base ACL rule 2 (MAC-based or IP-based) that is used for deriving new ACL rule.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.29601.2.21.4.1.1.12
issAclUserDefinedFilterSubAction This object specifies the action that is to be taken on the incoming packet is detailed below - none - no action modifyVlan - Traffic matching ACL rule will have VLAN ID classified/modified to value…	Enumerationr/w Enumerated Values: 0 none 1 modifyVlan 2 nestedVlan	.1.3.6.1.4.1.29601.2.21.4.1.1.13
issAclUserDefinedFilterSubActionId Id to be used if the object as specified by issAclUserDefinedFilterSubAction is either modifyvlan or nestedvlan only. Non-Zero value need to be specify when issAclUserDefinedFilterSubAction is modify or Nested Vlan. V…	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.29601.2.21.4.1.1.14
issAclUserDefinedFilterRedirectId This object specifies the redirect index associated with UserDefinedFilter entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.29601.2.21.4.1.1.15
issAclUserDefinedFilterStatus This object speifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.29601.2.21.4.1.1.16

This object specifies an interface group which is a collection of physical ports ( or ) trunks that
are grouped together for distributing traffic received on an ingress interface.
Based on the access-list match on an incoming interface, traffic is distributed 
among the member ports of an interface-group/virtual trunk.

issRedirectInterfaceGrpEntry row .1.3.6.1.4.1.29601.2.21.5.1.1

This object specifies that there is one entry in this table for each created Interface-Group.
An interface-group/virtual trunk is uniquely identified by the object 'issRedirectInterfaceGrpId'.

Indexes

issRedirectInterfaceGrpId

Column	Syntax	OID
issRedirectInterfaceGrpId This object specifies an Index to the Redirect Interface Group table entry. Uniquely identifies the interface-group.	IndexInteger Type Constraints: range: 1..65535	.1.3.6.1.4.1.29601.2.21.5.1.1.1
issRedirectInterfaceGrpFilterType This object specifies the type of the access-control list. The type could take the value 'l2filter' for MAC-based ACLs and 'l3filter' for IP-based ACLs. It takes the value 'userdefined' for filtering based on user-defin…	Enumerationr/w Enumerated Values: 0 l2filter 1 l3filter 2 userdefined	.1.3.6.1.4.1.29601.2.21.5.1.1.2
issRedirectInterfaceGrpFilterId This Object specifies the ID of the MAC-based, IP-based or UserDefined access control list/filter-rule, the details of which should be matched against the incoming packet. The corresponding ACL/filter-rule can be appli…	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.29601.2.21.5.1.1.3
issRedirectInterfaceGrpDistByte This object specifies the Distribution Byte that needs to be used for deriving the traffic distribution hash-logic for the set of interfaces in the interface-group/virtual-trunk. The output of the hash-logic is an egre…	Integer32r/w Constraints: range: 0-140	.1.3.6.1.4.1.29601.2.21.5.1.1.4
issRedirectInterfaceGrpPortList Each octet in this object specifies the IfIndex of a physical interface or manually aggregated trunk.Based on the value specified by issRedirectInterfaceGrpType This PortList specifies either of the below. -> if issRedi…	PortListr/w	.1.3.6.1.4.1.29601.2.21.5.1.1.5
issRedirectInterfaceGrpType This object specifies whether the redirected interface is a single port or portlist.If the value of this object is port(1) then the redirected interface is a single interface .If the value of this object is portlist(2…	Enumerationr/w Enumerated Values: 1 port 2 portList	.1.3.6.1.4.1.29601.2.21.5.1.1.6
issRedirectInterfaceGrpUdbPosition This object specifies the User defined postion of a byte in the packet when the value of the object as specified by issRedirectInterfaceGrpDistByte is udb.	Integer32r/w Constraints: range: 0-128	.1.3.6.1.4.1.29601.2.21.5.1.1.7
issRedirectInterfaceGrpStatus This object specifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry is 'not-ready' when the mandatory parameters are not specified. Following objects a…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.29601.2.21.5.1.1.8

A table to configure IEEE802 Reserved Multicast-MAC Address filter rules in the system.
The reserved transmission control function is a function that takes frames that normally are
sent to the CPU and then it decides to either permit them or to stop forwarding them to the CPU.

issReservedFrameCtrlEntry row .1.3.6.1.4.1.29601.2.21.7.1.1

An Reserved-Frame-Tranmission-Entry is uniquely identified by the object 'issReservedFrameTxnCtrlId'.

Indexes

issReservedFrameCtrlId

Column	Syntax	OID
issReservedFrameCtrlId Index to the ReservedFrameTxnCtrl entry. Uniquely identifies the issReservedFrameTxnCtrl entry.	IndexInteger Type Constraints: range: 1..65535	.1.3.6.1.4.1.29601.2.21.7.1.1.1
issReservedFrameCtrlPktType This object specifies the type of the PDUs. The type could take the following values bpdu - (MAC:01:80:C2:00:00:00) for Suppressing BPDU CPU transfer (Cannot be combined with Spanning Tree Protocol). lacpdu-udld - (MAC:…	ReservedFrameTyper/w Type Values: 1 bpdu 2 lacpdu-udld 3 eap 4 lldpdu 5 other 6 all	.1.3.6.1.4.1.29601.2.21.7.1.1.2
issReservedFrameCtrlAction Action value allow/drop specify the action to be taken on the packet if the ReservedFrameCtrl-entry matches. --> If the action is 'allow', the packet will be forwarded. --> If the action is 'drop', the packet will be…	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.29601.2.21.7.1.1.3
issReservedFrameCtrlOtherMacAddr Reserved Destination Multicast MAC address to be matched with the packet	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.29601.2.21.7.1.1.4
issReservedFrameCtrlOtherMacMask The range of Mac addresses will be decided based on the Mask Specified. The possible masks are : Mask Value MAC addresses 0xff 1 0xfe 2 0xfc 4 0xf8 8 0xf0 …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.29601.2.21.7.1.1.5
issReservedFrameCtrlMatchCount Number of times this ReservedFrameCtrl-entry is matched.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.29601.2.21.7.1.1.6
issReservedFrameCtrlStatsEnabledStatus This object specifies the status of ReservedFrameCtrl-entry statistics collection. When set as enabled, the number of hits for the specific entry is collected and can be verified using the issReservedFrameCtrlMatchC…	EnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.29601.2.21.7.1.1.7
issClearReservedFrameCtrlStats This object clears the hit count of the specific ReservedFrameCtrl-entry. When this object is set as 'true'(1), the hit count for the filter is cleared and the object value is reset to 'false'(2). The ge…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.29601.2.21.7.1.1.8
issReservedFrameCtrlStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry is 'not-ready' when the mandatory parameters are not specified. Following objects a…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.29601.2.21.7.1.1.9