rmSelectChannel

AQUARADIO-MIB · .1.3.6.1.4.1.3942.1.1.2.1.1.22
MIB view Table view

Object

column r/w Enumeration 
0 is always returned for GET operations.
For SET operation:
1 means 'change frequency if better choice exists,
else keep current value';
2 means 'change frequency in any case,
then use the best choice among the remaining values'

Context

MIB
AQUARADIO-MIB
OID
.1.3.6.1.4.1.3942.1.1.2.1.1.22
Type
column
Access
readwrite
Status
current
Parent
rmPropertiesEntry
Table
rmPropertiesTable
Siblings
21

Syntax

Enumeration

Values & Constraints

Enumerated Values
0reading-stub
1new
2renew

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rmPropertiesIfIndex
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as i…
columnInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.1
rmBurst
This value indicates whether burst mode support is turned on or off. The burst mode will be active when using MINT protocol and burst mode support is turned on both base station a…
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.10
rmLongRange
This value indicates whether long range mode is turned on or off. Long range mode allows to establish links at long distances. Regretfully, implementation of 802.11b protocol at A…
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.11
rmPowerCtl
This value indicates whether automatic power control mode is turned on or off.
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.12
rmTXRT
This attribute shall indicate the maximum number of transmission attempts of a unicast packet that shall be made before a failure condition is indicated. The default value of this…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.13
rmTXVRT
This attribute shall indicate the maximum number of transmission attempts of a unicast packet that shall be made before a failure condition is indicated, when voice mode is active…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.14
rmPTP
Turns on or off maximum air utilization mode. Can be used for high-speed point-to-point link, unsuitable for cell organization. (For 2Mbit radiomodules or radiomodules in LongRang…
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.15
rmWOCD
Turns on or off WOCD(without carrier detect) mode. Can be used on base station with marker access only. Allows to decrease retry packets number and therefore increase the performa…
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.16
rmBCsid
Turns on or off sid broadcast mode for greater security of the network. When sid broadcast is turned off, all devices in the network must have sid value set explicitly.
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.17
rmDistanceAuto
Turns on or off automatic adjustment of distance parameter.
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.18
rmNoiseFloor
The current noise floor in dBm.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.19
rmType
Radiomodule type.
columnOctetString.1.3.6.1.4.1.3942.1.1.2.1.1.2
rmBandwidth
Current radio channel size in KHz.
columnKHz SNMPv2-SMIUnsigned32.1.3.6.1.4.1.3942.1.1.2.1.1.20
rmChainMode
Radio channel technology.
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.21
rmFrequency
This value indicates radiomodule's operating frequency in KHz.
columnKHz SNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.3
rmBitRate
This value indicates radiomodule's current bitrate in kbits per second.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.4
rmSid
This value indicates radiomodule's sid.
columnRadioSID.1.3.6.1.4.1.3942.1.1.2.1.1.5
rmCurPowerLevel
This value indicates radiomodule's power output level (tenth dBm).
columntenth dBm. SNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.6
rmModulation
This value indicates radiomodule's modulation type.
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.7
rmAntenna
This value defines what antenna is used for receiving and transmission.
columnEnumeration.1.3.6.1.4.1.3942.1.1.2.1.1.8
rmDistance
This value indicates radiomodule's distance parameter in kilometers
columnkilometers SNMPv2-SMIInteger32.1.3.6.1.4.1.3942.1.1.2.1.1.9