rmBurst
AQUARADIO-MIB ·
.1.3.6.1.4.1.3942.1.1.2.1.1.10
Object
column
r/w
Enumeration
This value indicates whether burst mode support is turned on or off. The burst mode will be active when using MINT protocol and burst mode support is turned on both base station and CPE.
Context
- MIB
- AQUARADIO-MIB
- OID
.1.3.6.1.4.1.3942.1.1.2.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- rmPropertiesEntry
- Table
- rmPropertiesTable
- Siblings
- 21
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | on |
2 | off |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rmPropertiesIfIndex The index value which uniquely identifies the interface to
which this entry is applicable. The interface identified by
a particular value of this index is the same interface as
i… | column | Integer32 | .1.3.6.1.4.1.3942.1.1.2.1.1.1 |
| rmLongRange This value indicates whether long range mode is turned
on or off. Long range mode allows to establish links
at long distances. Regretfully, implementation of 802.11b
protocol at A… | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.11 |
| rmPowerCtl This value indicates whether automatic power control mode
is turned on or off. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.12 |
| rmTXRT This attribute shall indicate the maximum number of
transmission attempts of a unicast packet that shall be made
before a failure condition is indicated. The default value
of this… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.13 |
| rmTXVRT This attribute shall indicate the maximum number of
transmission attempts of a unicast packet that shall be made
before a failure condition is indicated, when voice mode
is active… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.14 |
| rmPTP Turns on or off maximum air utilization mode. Can be used
for high-speed point-to-point link, unsuitable for cell
organization. (For 2Mbit radiomodules or radiomodules
in LongRang… | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.15 |
| rmWOCD Turns on or off WOCD(without carrier detect) mode. Can be used
on base station with marker access only. Allows to decrease
retry packets number and therefore increase the performa… | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.16 |
| rmBCsid Turns on or off sid broadcast mode for greater security of the
network. When sid broadcast is turned off, all devices
in the network must have sid value set explicitly. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.17 |
| rmDistanceAuto Turns on or off automatic adjustment of distance parameter. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.18 |
| rmNoiseFloor The current noise floor in dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.19 |
| rmType Radiomodule type. | column | OctetString | .1.3.6.1.4.1.3942.1.1.2.1.1.2 |
| rmBandwidth Current radio channel size in KHz. | column | KHz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3942.1.1.2.1.1.20 |
| rmChainMode Radio channel technology. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.21 |
| rmSelectChannel 0 is always returned for GET operations.
For SET operation:
1 means 'change frequency if better choice exists,
else keep current value';
2 means 'change frequency in any case,
the… | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.22 |
| rmFrequency This value indicates radiomodule's operating frequency in KHz. | column | KHz SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.3 |
| rmBitRate This value indicates radiomodule's current bitrate in kbits
per second. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.4 |
| rmSid This value indicates radiomodule's sid. | column | RadioSID | .1.3.6.1.4.1.3942.1.1.2.1.1.5 |
| rmCurPowerLevel This value indicates radiomodule's power output level (tenth dBm). | column | tenth dBm. SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.6 |
| rmModulation This value indicates radiomodule's modulation type. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.7 |
| rmAntenna This value defines what antenna is used for receiving
and transmission. | column | Enumeration | .1.3.6.1.4.1.3942.1.1.2.1.1.8 |
| rmDistance This value indicates radiomodule's distance parameter
in kilometers | column | kilometers SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3942.1.1.2.1.1.9 |