bsnGlobalDot11bShortPreamble
AIRESPACE-WIRELESS-MIB ·
.1.3.6.1.4.1.14179.2.3.2.1.19
Object
scalar
r/w
Enumeration
802.11b Short Preamble.
Context
- MIB
- AIRESPACE-WIRELESS-MIB
- OID
.1.3.6.1.4.1.14179.2.3.2.1.19- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- bsnGlobalDot11bConfig
- Siblings
- 34
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bsnGlobalDot11bNetworkStatus 802.11b Network Admin Status. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.1 |
| bsnGlobalDot11bDynamicTxPowerControlInterval When Tx PowerControl dynamic alogirthm is running, this
interval(in secs) specifies how often TxPower control updates
are attempted on an Airespace AP. NOTE: hysteresis is
build i… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.2.1.10 |
| bsnGlobalDot11bCurrentTxPowerLevel The TxPowerLevel N currently being used to transmit data.
Some PHYs also use this value to determine the receiver
sensitivity requirements for CCA. | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.2.1.11 |
| bsnGlobalDot11bInputsForDTP This attribute is a bit mask specifying what to include in
DCA optimization.Below is a list of parameters and their
corresponding bits identifiers.
options … | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.2.1.12 |
| bsnGlobalDot11bPowerUpdateCmdInvoke When set to activate this starts a DTP calculation regardless
of the dynamic update interval. This command should be
invoke on Group Leader Airespace Switch.Invoking on a
Airesp… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.13 |
| bsnGlobalDot11bPowerUpdateCmdStatus After setting bsnGlobalDot11aChannelUpdateCmdInvoke to
activate, the result of action can be monitored from here. It
takes 5 minutes for the command to complete. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.14179.2.3.2.1.14 |
| bsnGlobalDot11bDataRate1Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.15 |
| bsnGlobalDot11bDataRate2Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.16 |
| bsnGlobalDot11bDataRate5AndHalfMhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.17 |
| bsnGlobalDot11bDataRate11Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.18 |
| bsnGlobalDot11bBeaconPeriod This attribute shall specify the number of TU that a
AP Radio shall use for scheduling Beacon tranmissions.
This value is transmitted in Beacon and Probe Response
frames. | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.2.1.2 |
| bsnGlobalDot11bDot11gSupport This attribute is enabled to also support 802.11g protocol on the
802.11b network. Enabling 802.11g allows additional data
rates: 6, 9, 12, 18, 24, 36, 48, 54 Mbps. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.20 |
| bsnGlobalDot11bDataRate6Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.21 |
| bsnGlobalDot11bDataRate9Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.22 |
| bsnGlobalDot11bDataRate12Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.23 |
| bsnGlobalDot11bDataRate18Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.24 |
| bsnGlobalDot11bDataRate24Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.25 |
| bsnGlobalDot11bDataRate36Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.26 |
| bsnGlobalDot11bDataRate48Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.27 |
| bsnGlobalDot11bDataRate54Mhz Specify if this rate is supported or mandatory or disabled. This
is configurable only if 802.11g support is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.28 |
| bsnGlobalDot11bPicoCellMode Configures the 802.11b pico-cell mode. This cannot be enabled
when the Fast Roaming Mode is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.29 |
| bsnGlobalDot11bDynamicChannelAssignment Dynamic channel assignment(DCA) has three modes. When the mode
is auto, the channel assignment will be periodically updated for
all Airespace APs that permit this operation. When … | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.3 |
| bsnGlobalDot11bFastRoamingMode Configures the 802.11b fast-roaming mode. This cannot be enabled
when the Pico Cell Mode is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.30 |
| bsnGlobalDot11bFastRoamingVoipMinRate Configures the minimum transmission rate allowed for VoIP on any
802.11b radio. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.31 |
| bsnGlobalDot11bFastRoamingVoipPercentage Configures the percentage of effective bandwidth for the minimum
rate reserved for VoIP. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.32 |
| bsnGlobalDot11b80211eMaxBandwidth This represents the maximum bandwidth allocated to 802.11e
clients. It is expressed as percentage of the total bandwidth of
802.11b network. The value of this attribute can vary… | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.2.1.33 |
| bsnGlobalDot11bDTPCSupport This attribute may be used to enable the DTPC support on all
802.11b/g radios. DTPC or Dynamic Transmit Power Control support
means that the radio's transmit power will be advert… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.34 |
| bsnGlobalDot11bRxSopThreshold This attribute may be used to configure Rxsop or receiver start
of packet custom values for 802.11b/g radios. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.35 |
| bsnGlobalDot11bCurrentChannel The current operating frequency channel of the DSSS
PHY. Valid channel numbers are as defined in 15.4.6.2.
This attribute will be read-only if
bsnAPIfPhyChannelAutomaticOn is tru… | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.2.1.4 |
| bsnGlobalDot11bDynamicChannelUpdateInterval When Channel dynamic alogirthm is running, this interval (in
secs) specifies how often Channel assignement updates are
attempted on an Airespace AP. NOTE: hysteresis is built int… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.2.1.5 |
| bsnGlobalDot11bInputsForDCA This attribute is a bit mask specifying what to include in
DCA optimization.Below is a list of parameters and their
corresponding bits identifiers.
options … | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.2.1.6 |
| bsnGlobalDot11bChannelUpdateCmdInvoke When set to activate this starts a DCA calculation regardless
of the dynamic update interval. This command should be invoke
on Group Leader Airespace Switch.Invoking on a Airespac… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.7 |
| bsnGlobalDot11bChannelUpdateCmdStatus After setting bsnGlobalDot11bChannelUpdateCmdInvoke to
activate, the result of action can be monitored from here. It
takes 5 minutes for the command to complete. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.14179.2.3.2.1.8 |
| bsnGlobalDot11bDynamicTransmitPowerControl Dynamic transmit power (DTP) has three modes. When the mode
is auto, the transmit power of each Airespace AP will be
periodically updated for all Airespace APs that permit this
… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.2.1.9 |