bsnGlobalDot11aInputsForDTP
AIRESPACE-WIRELESS-MIB ·
.1.3.6.1.4.1.14179.2.3.3.1.15
Object
This attribute is a bit mask specifying what to include in
DCA optimization.Below is a list of parameters and their
corresponding bits identifiers.
options bit
--------------------------------------
none 0
LOAD 1
SIGNAL STRENGTH 2
FOREIGN INTERFERENCE 4
NOISE 8
Default value is 15( all bits on).
Context
- MIB
- AIRESPACE-WIRELESS-MIB
- OID
.1.3.6.1.4.1.14179.2.3.3.1.15- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- bsnGlobalDot11aConfig
- Siblings
- 31
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bsnGlobalDot11aNetworkStatus Dot11a Network Status | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.1 |
| bsnGlobalDot11aChannelUpdateCmdInvoke When set to activate this starts a DCA calculation regardless
of the dynamic update interval. This command should be invoke
on Group Leader Airespace Switch.Invoking on a Airespac… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.10 |
| bsnGlobalDot11aChannelUpdateCmdStatus After setting bsnGlobalDot11aChannelUpdateCmdInvoke to
activate, the result of action can be monitored from here. It
takes 5 minutes for the command to complete. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.14179.2.3.3.1.11 |
| bsnGlobalDot11aDynamicTransmitPowerControl Dynamic transmit power (DTP) has three modes. When the mode
is auto, the transmit power of each Airespace AP will be
periodically updated for all Airespace APs that permit this
… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.12 |
| bsnGlobalDot11aCurrentTxPowerLevel The TxPowerLevel N currently being used to transmit data.
Some PHYs also use this value to determine the receiver
sensitivity requirements for CCA. | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.3.1.13 |
| bsnGlobalDot11aDynamicTxPowerControlInterval When Tx PowerControl dynamic alogirthm is running, this
interval(in secs) specifies how often TxPower control updates
are attempted on an Airespace AP. NOTE: hysteresis is
build i… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.3.1.14 |
| bsnGlobalDot11aPowerUpdateCmdInvoke When set to activate this starts a DTP calculation regardless
of the dynamic update interval. This command should be invoke
on Group Leader Airespace Switch.Invoking on a Airespac… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.16 |
| bsnGlobalDot11aPowerUpdateCmdStatus After setting bsnGlobalDot11aChannelUpdateCmdInvoke to
activate, the result of action can be monitored from here. It
takes 5 minutes for the command to complete. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.14179.2.3.3.1.17 |
| bsnGlobalDot11aDataRate6Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.19 |
| bsnGlobalDot11aLowBandNetwork Dot11a Low Band Network Status | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.2 |
| bsnGlobalDot11aDataRate9Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.20 |
| bsnGlobalDot11aDataRate12Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.21 |
| bsnGlobalDot11aDataRate18Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.22 |
| bsnGlobalDot11aDataRate24Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.23 |
| bsnGlobalDot11aDataRate36Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.24 |
| bsnGlobalDot11aDataRate48Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.25 |
| bsnGlobalDot11aDataRate54Mhz Specify if this rate is supported or mandatory or disabled | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.26 |
| bsnGlobalDot11aPicoCellMode Configures the 802.11a pico-cell mode. This cannot be enabled
when the Fast Roaming Mode is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.27 |
| bsnGlobalDot11aFastRoamingMode Configures the 802.11a fast-roaming mode. This cannot be enabled
when the Pico Cell Mode is enabled. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.28 |
| bsnGlobalDot11aFastRoamingVoipMinRate Configures the minimum transmission rate allowed for VoIP on any
802.11a radio. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.29 |
| bsnGlobalDot11aMediumBandNetwork Dot11a Mid Band Network Status | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.3 |
| bsnGlobalDot11aFastRoamingVoipPercentage Configures the percentage of effective bandwidth for the minimum
rate reserved for VoIP. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.30 |
| bsnGlobalDot11a80211eMaxBandwidth This represents the maximum bandwidth allocated to 802.11e
clients. It is expressed as percentage of the total bandwidth
of 802.11a network. The value of this attribute can vary… | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.3.1.31 |
| bsnGlobalDot11aDTPCSupport This attribute may be used to enable the DTPC support on all
802.11a radios. DTPC or Dynamic Transmit Power Control support
means that the radio's transmit power will be advertis… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.32 |
| bsnGlobalDot11aRxSopThreshold This attribute may be used to configure Rxsop or receiver start
of packet custom values for 802.11a radios. | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.33 |
| bsnGlobalDot11aHighBandNetwork Dot11a High Band Network Status | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.4 |
| bsnGlobalDot11aBeaconPeriod This attribute shall specify the number of TU that a
AP Radio shall use for scheduling Beacon tranmissions.
This value is transmitted in Beacon and Probe Response
frames. | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.3.1.5 |
| bsnGlobalDot11aDynamicChannelAssignment Dynamic channel assignment(DCA) has three modes. When the mode
is auto, the channel assignment will be periodically updated
for all Airespace APs that permit this operation. When… | scalar | Enumeration | .1.3.6.1.4.1.14179.2.3.3.1.6 |
| bsnGlobalDot11aCurrentChannel The number of the current operating frequency channel of the
OFDM PHY. | scalar | Integer32 | .1.3.6.1.4.1.14179.2.3.3.1.7 |
| bsnGlobalDot11aDynamicChannelUpdateInterval When Channel dynamic alogirthm is running, this interval(in
secs) specifies how often Channel assignement updates are
attempted on an Airespace AP. NOTE: hysteresis is
build into… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.3.1.8 |
| bsnGlobalDot11aInputsForDCA This attribute is a bit mask specifying what to include in
DCA optimization.Below is a list of parameters and their
corresponding bits identifiers.
options … | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.14179.2.3.3.1.9 |