bsnAPType

AIRESPACE-WIRELESS-MIB · .1.3.6.1.4.1.14179.2.2.1.1.22
MIB view Table view

Object

column Enumeration 
This is the model of the AP in enumeration.
Ap models start with wap are called panda
ap models.Ap models ended with different suffix
have different functionalities.
              
i     : Ap with internal antenna
e     : Ap with external antena
t     : teleworker Aps
p     : stadium Aps
w     : wall mountable Aps
agn   : supports dot11(a),dot11(g),dot11(n)
gn    : supports dot11(g),dot11(n)

Context

MIB
AIRESPACE-WIRELESS-MIB
OID
.1.3.6.1.4.1.14179.2.2.1.1.22
Type
column
Access
readonly
Status
current
Parent
bsnAPEntry
Table
bsnAPTable
Siblings
30

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
bsnAPDot3MacAddress
The MAC address of an AP.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.14179.2.2.1.1.1
bsnAPPrimaryMwarName
sysName of the Airespace Switch which is suppose to be the Primary MWAR(switch) of the AP with which AP should associate. This work when AP is not directly connected to Airespace …
columnOctetString.1.3.6.1.4.1.14179.2.2.1.1.10
bsnAPReset
Set this attribute to reset the AP. When it comes up it will try to associate with the Primary Switch if that is set, else it will associate with the Master Switch. Reading this a…
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.11
bsnAPStatsTimer
Configures the time interval in secs after which bsnAPDot11Counters Stats is sent from AP to Switch. If not configured this value is 0 which means never send the stats.
columnInteger32.1.3.6.1.4.1.14179.2.2.1.1.12
bsnAPPortNumber deprecated
Port on the Switch on which this APs traffic is coming through.
columnInteger32.1.3.6.1.4.1.14179.2.2.1.1.13
bsnAPModel
AP Model
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.14179.2.2.1.1.16
bsnAPSerialNumber
AP Serial Number.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.14179.2.2.1.1.17
bsnAPClearConfig
Set this attribute to clear AP configuration and reset it to factory defaults. Reading this attribute will always return 0
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.18
bsnApIpAddress
IP address of the AP. This will not be available when the switch is operating in the Layer2 mode. In this case, the attribute will return 0 as value.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.14179.2.2.1.1.19
bsnAPNumOfSlots
Number of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g.
columnInteger32.1.3.6.1.4.1.14179.2.2.1.1.2
bsnAPMirrorMode
If enabled, then this AP's Client's Data is mirrored and this AP's clients are dynamically added to the switch's mirrored MAC list.
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.20
bsnAPRemoteModeSupport
This specifies if the the Remote Mode is supported on this AP or not. If supported user can set bsnAPMonitorOnlyMode to remote. Otherwise not.
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.21
bsnAPSecondaryMwarName
sysName of the Airespace Switch which is suppose to be the Secondary MWAR(switch) of the AP with which AP should associate if Primary Switch(configured through bsnAPPrimaryMwarNam…
columnOctetString.1.3.6.1.4.1.14179.2.2.1.1.23
bsnAPTertiaryMwarName
sysName of the Airespace Switch which is suppose to be the Tertiary MWAR(switch) of the AP with which AP should associate. If primary,secondary and tertiary switch are not availab…
columnOctetString.1.3.6.1.4.1.14179.2.2.1.1.24
bsnAPIsStaticIP
This flag when disabled implies that AP will use DHCP to get the IP address. However, if it is enabled, then user should enter the IPAddress, Netmask and Gateway.
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.25
bsnAPNetmask
The Netmask of the IP address of the AP.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.14179.2.2.1.1.26
bsnAPGateway
The Gateway for the AP.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.14179.2.2.1.1.27
bsnAPStaticIPAddress
The Static IP-Address configuration for the AP. This can only be changed when the LWAPP mode is in Layer-3.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.14179.2.2.1.1.28
bsnAPBridgingSupport
This specifies if this AP is a Bridging AP. Bridging APs can be used in Bridging or Mesh network configurations.
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.29
bsnAPName
Name assigned to this AP. If an AP is not configured its factory default name will be ap:<last three byte of MACAddress> eg. ap:af:12:be
columnOctetString.1.3.6.1.4.1.14179.2.2.1.1.3
bsnAPGroupVlanName
The AP Group to which this AP has been associated with. If it is empty, then no AP Group overriding has been set.
columnOctetString.1.3.6.1.4.1.14179.2.2.1.1.30
bsnAPIOSVersion
IOS Version of IOS Cisco AP. Zero length string will be returned for other APs
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.14179.2.2.1.1.31
bsnAPCertificateType
Enum values denoting AP Certificate Type. 1 : manufactureinstalled : Manufacture Installed Certificate type (MIC). 2 : selfsigned : Self Signed Certificate type (SSC). 3 : lo…
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.32
bsnAPEthernetMacAddress
The Ethernet MAC address of the AP.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.14179.2.2.1.1.33
bsnAPAdminStatus deprecated
Admin State of the AP
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.37
bsnAPLocation
User specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the AP is located.
columnOctetString.1.3.6.1.4.1.14179.2.2.1.1.4
bsnAPMonitorOnlyMode
Monitor Only Mode Setting.
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.5
bsnAPOperationStatus
Operation State of the AP. When AP associates with the Airespace Switch its state will be associated. When Airespace AP is disassociated from the Switch, its state will be disass…
columnEnumeration.1.3.6.1.4.1.14179.2.2.1.1.6
bsnAPSoftwareVersion
Major Minor Software Version of AP
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.14179.2.2.1.1.8
bsnAPBootVersion
Major Minor Boot Version of AP
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.14179.2.2.1.1.9