h3cMainPsePowerLimit
A3COM-HUAWEI-POWER-ETH-EXT-MIB ·
.1.3.6.1.4.1.43.45.1.10.2.14.2.1.1
Object
The object specifies the power limit set for the unit as a whole. The PoE unit will already have a nominal power defined by the IETF Power MIB [1] pethMainPsePower object. This OPTIONAL object specifies a further limit to this nominal power value. This may be useful to control the thermals of the unit, or for internal testing purposes. One possible use for this object may be to lower the power consumption of the unit if one or more of the internal fans have broken. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts).
Context
- MIB
- A3COM-HUAWEI-POWER-ETH-EXT-MIB
- OID
.1.3.6.1.4.1.43.45.1.10.2.14.2.1.1- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- h3cMainPseEntry
- Table
- h3cMainPseTable
- Siblings
- 6
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| h3cMainPseAveragePower The object specifies the average power which has been consumed
by the port. It is a read/write integer value with units of
Watts (note - Watts is chosen instead of milliWatts her… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.2 |
| h3cMainPsePeakPower The object specifies the peak power which has been consumed for PoE.
It is defined as the highest measured value of power in milliWatts
that has been consumed at any one point in … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.3 |
| h3cMainGuaranteedPowerRemaining The object specifies the amount of power remaining in the guaranteed
power pool. Each time a port is placed into guaranteed mode it
reserves a set amount of power out of the tota… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.4 |
| h3cMainPsePriorityMode Describes or controls the priority mode on slot which must be
enabled firstly. When a new board is inserted, and the power is
over-load, a value of disconnection(0) means that th… | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.5 |
| h3cMainPseLegacy Describes or controls the legacy mode on slot which must be enabled
firstly. Legacy mode: standard or nonstandard PD detection mode. | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.6 |
| h3cMainPsePowerPriority Describes or controls the priority of the PSE. The priority
will be used by the PSE policy to prevent from power overloading.
If the priority of PSE is set to critical, the PSE w… | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.7 |