h3cMainPsePeakPower
A3COM-HUAWEI-POWER-ETH-EXT-MIB ·
.1.3.6.1.4.1.43.45.1.10.2.14.2.1.3
Object
The object specifies the peak power which has been consumed for PoE. It is defined as the highest measured value of power in milliWatts that has been consumed at any one point in time by the sum of the PoE ports. Its value is only reset when the unit is powered on or when it is manually reset by the user as specifiedbelow. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts). Writing a value of zero to this object resets its value to zero. Writing any other value to this object has noeffect on its value and an error is returned.
Context
- MIB
- A3COM-HUAWEI-POWER-ETH-EXT-MIB
- OID
.1.3.6.1.4.1.43.45.1.10.2.14.2.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- h3cMainPseEntry
- Table
- h3cMainPseTable
- Siblings
- 6
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| h3cMainPsePowerLimit The object specifies the power limit set for the unit as a whole.
The PoE unit will already have a nominal power defined by the
IETF Power MIB [1] pethMainPsePower object. This O… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.1 |
| h3cMainPseAveragePower The object specifies the average power which has been consumed
by the port. It is a read/write integer value with units of
Watts (note - Watts is chosen instead of milliWatts her… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.2 |
| h3cMainGuaranteedPowerRemaining The object specifies the amount of power remaining in the guaranteed
power pool. Each time a port is placed into guaranteed mode it
reserves a set amount of power out of the tota… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.4 |
| h3cMainPsePriorityMode Describes or controls the priority mode on slot which must be
enabled firstly. When a new board is inserted, and the power is
over-load, a value of disconnection(0) means that th… | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.5 |
| h3cMainPseLegacy Describes or controls the legacy mode on slot which must be enabled
firstly. Legacy mode: standard or nonstandard PD detection mode. | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.6 |
| h3cMainPsePowerPriority Describes or controls the priority of the PSE. The priority
will be used by the PSE policy to prevent from power overloading.
If the priority of PSE is set to critical, the PSE w… | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.14.2.1.7 |