XF-RADIOLINK-PTP-RADIO-MIB Table View

Table for Radiolink point-to-point radios managed objects.
Table indexed with entPhysicalIndex.

xfRAUEntry row .1.3.6.1.4.1.193.81.3.4.3.1.1.1

An entry in xfRadioTable.

Indexes

ENTITY-MIBentPhysicalIndex

Column	Syntax	OID
xfRAUAlarmStatus This object shows the alarm status of the radio unit. atpcCability - The terminal is configured for ATPC, but the radio does not support ATPC. This alarm is activated only if ATPC is turned on (any direct…	Bits Enumerated Values: 0 atpcCapability0 1 atpcCapability1 2 atpcCapability2 3 configurationInvalid0 4 configurationInvalid1 5 configurationInvalid2 6 sdcHwErrorMain0 7 sdcHwErrorMain1 8 sdcHwErrorMain2 9 sdcHwErrorDiv0 10 sdcHwErrorDiv1 11 sdcHwErrorDiv2 12 sdcDadeCalMismatch0 13 sdcDadeCalMismatch1 14 sdcDadeCalMismatch2 15 insufficientResourceRauXpic0 16 insufficientResourceRauXpic1 17 insufficientResourceRauXpic2 18 companionRauMismatch0 19 companionRauMismatch1 20 companionRauMismatch2	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.1
xfRAURfLoopAvailable This object inidicates if RF loop is available in radio unit.	RAURfLoopAvailable Type Values: 1 other 2 rfLoopAvailable 3 rfLoopNotAvailable Description: This TC enumerates the RF loop.	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.2
xfRAUAtpcCapability This object indicates if the radio unit supports ATPC or not.	RAUAtpcCapability Type Values: 1 other 2 noAtpcSupport 3 doesNotExist 4 atpcCapabilityUnknown 5 supportsAtpc Description: This TC enumerates the ATPC capability.	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.3
xfRAULocalCtrlCapability This object indicates if the radio unit supports local transmit power control or not.	Enumeration Enumerated Values: 1 other 2 noLocalControlSupport 3 supportsLocalControl	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.4
xfRAUModCapability This object shows the modulation methods supported by the radio unit.	RAUModCapability Type Values: 0 cqpsk 1 qam16 2 qam128 3 qam32 4 qam64 Description: This TC enumerates the modulation capabilities. Modulation capabilities is indicated by 5 bits: bits 01234 00000 undetermined 00001 C-QPSK 00010 16-QAM 00011 C-QPSK & 16-QAM 00100 128-QAM 01000 32-QAM …	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.5
xfRAUFrequencyband This object shows the frequency band for the radio unit.	Unsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.6
xfRAUSubBand This object shows the sub band (Index) for the radio unit.	Unsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.7
xfRAUTemperature This object shows the temperature, in degree Celsius, inside the radio unit.	Integer32 Constraints: range: -127-127	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.8
xfRAUProtectionPath This object indicates what radio path the radio belongs to.	Enumeration Enumerated Values: 1 other 2 rauRa1 3 rauRa2	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.9
xfRAURxCapability This object indicates if the radio unit support RX configuration.	Enumeration Enumerated Values: 1 other 2 rxSupport	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.10
xfRAUNotes You can add information in this description field, for example polarization, antenna type or logging a site visit.	OctetStringr/w Constraints: range: 0-800	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.11
xfRauAtpcVersion This object represents the RAU ATPC version.	Enumeration Enumerated Values: 1 other 2 version1 3 version2 4 version3	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.12
xfRauBoosterCapability This object represents the Booster capability for a link.	BoosterCapability Type Values: 1 other 2 noBoosterSupport 3 boosterSupport Description: Booster capabilities values codes.	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.13
xfRauBoosterSelectedIndex This object represents the Booster selected index for a link.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.1.1.14

Table for Radiolink point-to-point radios RF IF managed objects.
Table indexed with ifIndex.

xfRFIFEntry row .1.3.6.1.4.1.193.81.3.4.3.1.2.1

An entry in the xfRFIFTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
xfRFBaseTxFrequency This object shows the Tx frequency in KHz when frequency step number is 0.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.1
xfRFBaseRxFrequency This object shows the Rx frequency in KHz when frequency. step number is 0	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.2
xfRFStepSize This object shows the frequency step size in KHz.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.3
xfRFStepLimitLow This object shows the lowest allowed frequency step number.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.4
xfRFStepLimitHigh This object shows the highest allowed frequency step number.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.5
xfRFCurrentStepNumber This object sets/shows the frequency step number. 0 = frequency not yet defined. For Classic RAUs, TX and RX frequencies can not be set individually. The span between them is always fixed and depends on d…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.6
xfRFTxOperStatus This object shows the operational status of the transmitter.	RFTxOperStatus Type Values: 1 other 2 txOff 3 txOn 4 txStandby Description: This TC enumerates the Tx operational status.	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.7
xfRFTxAdminStatus This object sets the desired status of the transmitter. Value other(1) not settable. Especially for far end: txOff(2), requests far end transmitter to be turned off. txOn(3), requests far end transmit…	Enumerationr/w Enumerated Values: 1 other 2 txOff 3 txOn	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.8
xfRFLoopEnable This object manage RF loop. Default value: disable(3). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 enable 3 disable	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.9
xfRFAlarms This TC enumerates the alarms for RF interface. txFrequency - Transmitter frequency synthesizer loop is unlocked. rxFrequency - Receiver frequency synthesizer loop is unlocked. rfOutputLevel - Major degr…	Bits Enumerated Values: 0 txFrequency0 1 txFrequency1 2 txFrequency2 3 rxFrequency0 4 rxFrequency1 5 rxFrequency2 6 rfOutputLevel0 7 rfOutputLevel1 8 rfOutputLevel2 9 rxAfc0 10 rxAfc1 11 rxAfc2 12 rfInputLevel0 13 rfInputLevel1 14 rfInputLevel2 15 rfInputThreshold0 16 rfInputThreshold1 17 rfInputThreshold2 18 rfOutputLevelATPC0 19 rfOutputLevelATPC1 20 rfOutputLevelATPC2 21 sdcRfInputLevelMain0 22 sdcRfInputLevelMain1 23 sdcRfInputLevelMain2 24 sdcRfInputLevelDiv0 25 sdcRfInputLevelDiv1 26 sdcRfInputLevelDiv2 27 rlts1Counter15m0 28 rlts1Counter15m1 29 rlts1Counter15m2 30 rlts2Counter15m0 31 rlts2Counter15m1 32 rlts2Counter15m2 33 rltmCounter15m0 34 rltmCounter15m1 35 rltmCounter15m2 36 tlts1Counter15m0 37 tlts1Counter15m1 38 tlts1Counter15m2 39 tltmCounter15m0 40 tltmCounter15m1 41 tltmCounter15m2 42 rlts1Counter24h0 43 rlts1Counter24h1 44 rlts1Counter24h2 45 rlts2Counter24h0 46 rlts2Counter24h1 47 rlts2Counter24h2 48 rltmCounter24h0 49 rltmCounter24h1 50 rltmCounter24h2 51 tlts1Counter24h0 52 tlts1Counter24h1 53 tlts1Counter24h2 54 tltmCounter24h0 55 tltmCounter24h1 56 tltmCounter24h2 57 remoteRfIfHighestSeverityAlarm0 58 remoteRfIfHighestSeverityAlarm1 59 remoteRfIfHighestSeverityAlarm2 60 ifcabledamaged0 61 ifcabledamaged1 62 ifcabledamaged2	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.10
xfRFStatus This object shows the RAU status. rfLoop - Warns if RF-loop is enabled on RAU txOff - Warns if TX is manually set to off	Bits Enumerated Values: 0 rfLoop0 1 rfLoop1 2 rfLoop2 3 txOff0 4 txOff1 5 txOff2	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.11
xfRFStepSizeRx This object shows the Rx frequency step size in KHz.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.12
xfRFStepLimitLowRx This object shows the Rx lowest allowed frequency step number.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.13
xfRFStepLimitHighRx This object shows the Rx highest allowed frequency step number.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.14
xfRFCurrentStepNumberRx This object sets/shows the RX frequency step number for Agile RAUs. 0 = frequency not yet defined. - To calculate step number for RX, use the following formula: New step number Rx = (RX frequency - xfRA…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.15
xfRFDuplexType This object tells the duplex frequency mode for the RAU: - fixed: Tx frequency only can be set by operator, Rx frequency is automatically set on the basis of (fixed) RAU duplex frequency - variable: duplex frequency c…	Enumeration Enumerated Values: 1 other 2 fixed 3 variable	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.16
xfRFDuplexConfig This object enables setting of duplex frequency for the RAU. It is always disabled(3) and can not be overwritten if xfRFDuplexType = fixed(2).	Enumerationr/w Enumerated Values: 1 other 2 enabled 3 disabled	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.17
xfRFDuplexDistance This object is aimed to select the duplex distance for the RAU. It can only be set if xfRFDuplexConfig = enabled(2), so that: xfRFDuplexDistance = Tx Frequency - Rx Frequency Otherwise, it is automatically filled o…	Integer32r/w Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.2.1.18

Table for Radiolink point-to-point radios managed objects.
Table indexed with ifIndex.

xfRFPowerEntry row .1.3.6.1.4.1.193.81.3.4.3.1.3.1

An entry in the xfRFPowerTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
xfRFCurrentOutputPower This object shows the output power in dBm including attenuator.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.1
xfRFRtpcMinOutputPower This object shows the minimum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.2
xfRFRtpcMaxOutputPower This object shows the maximum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.3
xfRFRtpcSelectedOutputPower This object set/shows the selected output power in dBm including attenuator. Value 254 indicates that the selected power is set to maximum. Default value: 254	Integer32r/w Constraints: range: -100-45 range: 254-254	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.4
xfRFAtpcMinOutputPower This object shows the minimum output power in dBm in ATPC. mode for radio contained in the radio terminal.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.5
xfRFAtpcMaxOutputPower This object sets/shows the ATPC maximum output power in dBm for radio contained in the radio terminal. Value 254 indicates that the power is set to maximum. Default value: 254.	Integer32r/w Constraints: range: -100-45 range: 254-254	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.6
xfRFAtpcMinInputPowerFar This object shows the ATPC minimum input target power level for far end radio.	Integer32 Constraints: range: -99--30 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.7
xfRFAtpcSelectedInputPowerFar This object sets/shows the ATPC selected input target level for far end radio. Default value: -30.	Integer32r/w Constraints: range: -99--30	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.8
xfRFAttenuator This object sets/shows the value in dBm for fixed attenuator mounted in antenna. Default value: 0.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.9
xfRFCurrentInputPower This object shows RF input level = value/10 dBm. Domain: [-20.0 .. -99.9 dBm].	Integer32 Constraints: range: -999--200	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.10
xfRFMaxInputPowerLast7Days This object shows maximum RF input level last 7 days. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates invalid value.	Integer32 Constraints: range: -999--200 range: 0-0	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.11
xfRFMinInputPowerLast7Days This object shows minimum RF input level last 7 days. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates invalid value.	Integer32 Constraints: range: -999--200 range: 0-0	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.12
xfRFMaxInputPowerSinceReset This object shows maximum RF input level since reset. RF input level = value/10 dBm. Domain: [-20.0 .. -99.9 dBm].	Integer32 Constraints: range: -999--200	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.13
xfRFMinInputPowerSinceReset This object shows minimum RF input level since reset. RF input level = value/10 dBm. Domain: [-20.0 .. -99.9 dBm].	Integer32 Constraints: range: -999--200	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.14
xfRFInputPowerReset This object reset the registers for the RF input level and All Time High level this seven days period and counters for the next seven days period of time Note. For protected rlMLE and rlXfMLE terminals th…	Enumerationr/w Enumerated Values: 1 inputPowerReset	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.15
xfRFInputAlarmThreshold This object shows RF input level threshold. Default value: -93.	Integer32r/w Constraints: range: -99--30	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.16
xfRFOutputPower4QAM Output power for 4QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.17
xfRFOutputPower8QAM Output power for 8QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.18
xfRFOutputPower16QAM Output power for 16QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.19
xfRFOutputPower32QAM Output power for 32QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.20
xfRFOutputPower64QAM Output power for 64QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.21
xfRFOutputPower128QAM Output power for 128QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.22
xfRFOutputPower256QAM Output power for 256QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.23
xfRFOutputPower512QAM Output power for 512QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.24
xfRFAtpcFallbackOutputPower This object sets maximum output power in dBm in ATPCFallback mode for radio contained in the radio terminal. Value = 254 indicates that the power is set to maximum. Default value: 254.	Integer32r/w Constraints: range: -100-45 range: 254-254	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.25
xfRFAtpcFallbackEnable Enable/disable ATPCFallback.	ATPCFallbackEnabler/w Type Values: 1 other 2 disable 3 enable Description: ATPC fallback enable status.	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.26
xfRFAtpcFallbackTimer ATPC Fallback Timer specifies how long the output power can be at PATPC, MAX before ATPC fallback is triggered Default value: 15 min	Integer32r/w Constraints: range: 1-60	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.27
xfRFOutputPower1024QAM Output power for 1024QAM.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.28
xfRFMaxOutputPowerNotLimited Max output power in dBm including attenuator that the RAU can give if it is not power supply limited.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.29
xfRFMaxOutputPowerNotPossible unknown(0) isPossible(1) Max output power is possible due to power supply limitations isNotPossible(2) Max output power is not possible due to power supply limitations	Enumeration Enumerated Values: 0 unknown 1 isPossible 2 isNotPossible	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.30
xfRFCurrentInputPowerSdcMain This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).	Integer32 Constraints: range: -999--200 range: 0-0	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.31
xfRFCurrentInputPowerSdcDiv This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).	Integer32 Constraints: range: -999--200 range: 0-0	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.32
xfRFMeanInputPower1m This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value.	Integer32 Constraints: range: -999--200 range: 0-0	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.33
xfRFMaxOutputPowerLast7Days This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.34
xfRFMinOutputPowerLast7Days This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.35
xfRFMaxOutputPowerSinceReset This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.36
xfRFMinOutputPowerSinceReset This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.37
xfRFMaxMSELast7Days Indicate Max MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.	Integer32 Constraints: range: -1000-1000 range: 2000-2000	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.38
xfRFMinMSELast7Days Indicate Min MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.	Integer32 Constraints: range: -1000-1000 range: 2000-2000	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.39
xfRFMaxXPILast7Days Indicate Max Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.	Integer32 Constraints: range: -1000-1000 range: 2000-2000	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.40
xfRFMinXPILast7Days Indicate Min Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.	Integer32 Constraints: range: -1000-1000 range: 2000-2000	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.41
xfRFOutputPowerReset This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.	Enumerationr/w Enumerated Values: 1 outputPowerReset	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.42
xfRFBoosterGain Value of the Gain of the Booster	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.43
xfRFBoosterMaxInputPower Value of the Max Input Power admitted towards the Booster	Integer32 Constraints: range: -100-35 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.44
xfRFBoosterCapability Value of Booster capability according to the system	BoosterCapability Type Values: 1 other 2 noBoosterSupport 3 boosterSupport Description: Booster capabilities values codes.	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.45
xfRFBoosterProductNumber Product Number of the Booster connected to the specific RF IF	SNMPv2-TCDisplayStringr/w Constraints: range: 0-20 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.46
xfRFBoosterHWRevision HW Revision of the Booster connected to the specific RF IF	SNMPv2-TCDisplayStringr/w Constraints: range: 0-20 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.193.81.3.4.3.1.3.1.47

Table for RAU capability information.
Table indexed with entPhysicalIndex and xfTermRowIndex.

xfRAUCapabilityEntry row .1.3.6.1.4.1.193.81.3.4.3.1.4.1

An entry in xfRAUCapabilityTable.

Indexes

ENTITY-MIBentPhysicalIndex XF-RADIOLINK-PTP-TERMINAL-MIBxfTermRowIndex

Column	Syntax	OID
xfRAUChannelSpacing Channel spacing. ETSI: 3.5, 7, 14, 28, 40, 56 MHz ANSI: 10, 20, 30, 40, 50 MHz	RAUChannelSpacingCapability Type Values: 0 chspUnknown 1 chsp7MHz 2 chsp14MHz 3 chsp20MHz 4 chsp28MHz 5 chsp30MHz 6 chsp40MHz 7 chsp50MHz 8 chsp56MHz 9 chsp10MHz 10 chsp3500KHz 11 chsp60MHz Description: Channel spacing capability.	.1.3.6.1.4.1.193.81.3.4.3.1.4.1.1
xfRAUChannelModulation This object shows the modulation. Values: cqpsk(2) CQPSK qam16(3) 16-QAM qam128(4) 128-QAM qam32(5) 32-QAM qam64(6) 64-QAM qam4(7) 4-QAM qam8(8) 8-QAM qam256(9) 256-QAM qam512(1…	RAUModulation Type Values: 1 other 2 cqpsk 3 qam16 4 qam128 5 qam32 6 qam64 7 qam4 8 qam8 9 qam256 10 qam512 11 qam1024 Description: Type of modulation.	.1.3.6.1.4.1.193.81.3.4.3.1.4.1.2
xfRAUSpectrumEfficiencyClass Spectrum Efficiency Class: other(1), unknown sec2(2), Spectrum eff. Class 2 sec3(3), Spectrum eff. Class 3 sec4L(4), Spectrum eff. Class 4L sec4H(5), Specturm eff. Class 4H sec5A(6), Spectrum eff. Class 5A sec5B(7), S…	RauSec Type Values: 1 other 2 sec2 3 sec3 4 sec4L 5 sec4H 6 sec5A 7 sec5B 8 sec6A 9 sec6B Description: Spectrum Effeciency Class.	.1.3.6.1.4.1.193.81.3.4.3.1.4.1.3
xfRAUCarrierMode Radio carrier mode.	Enumeration Enumerated Values: 1 singleCarrier 2 xpicDualCarrier 3 mimoMultiCarrier	.1.3.6.1.4.1.193.81.3.4.3.1.4.1.4

Table for RAU Sub-Band index capability.
Table indexed with entPhysicalIndex and xfRAUSubBandIndex.

xfRAUSubBandEntry row .1.3.6.1.4.1.193.81.3.4.3.1.5.1

An entry in xfRAUSubBandTable.

Indexes

ENTITY-MIBentPhysicalIndex xfRAUSubBandIndex

Column	Syntax	OID
xfRAUSubBandIndex An index for the specific RAU Sub-Band available index range.	Unsigned32 Constraints: range: 1-255	.1.3.6.1.4.1.193.81.3.4.3.1.5.1.1
xfRAUSubBandRange This object shows the RAU Sub-Band available index range [0..255].	Unsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.193.81.3.4.3.1.5.1.2

Table for RF Spectrum Diagnostics control and status

xfRFSpectrumDiagEntry row .1.3.6.1.4.1.193.81.3.4.3.1.6.1

An entry in xfRFSpectrumDiagTable

Indexes

IF-MIBifIndex

Column	Syntax	OID
xfRFSpectrumDiagAdminStatus RF Spectrum Diagnostics Admin Status	Enumerationr/w Enumerated Values: 1 other 2 channelScanStart 3 subBandScanStart 255 scanStop	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.1
xfRFSpectrumDiagOperStatus RF Spectrum Diagnostics Oper Status	Enumeration Enumerated Values: 0 scanNotStarted 1 subBandScanOngoing 2 channelScanOngoing 3 scanCanceled 4 subBandScanFinished 5 channelScanFinished	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.2
xfRFSpectrumDiagChannelScanEstTime Estimated time in seconds for scanning one Channel Spacing at current RX frequency	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.3
xfRFSpectrumDiagSubBandScanEstTime Estimated time in seconds for scanning full Sub Band of connected RAU	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.4
xfRFSpectrumDiagScanDate Date and time when scan (channel or sub-band) is completed, format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss]	SNMPv2-TCDisplayString Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.5
xfRFSpectrumDiagChannelSpacing Channel width measured by Spectrum Diagnostics	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.6
xfRFSpectrumDiagCurrRxFrequency Current value of Rx frequency	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.7
xfRFSpectrumDiagMinRxFrequency Minimum sub-band Rx frequency (RAU lower edge)	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.8
xfRFSpectrumDiagMaxRxFrequency Maximum sub-band Rx frequency (RAU upper edge)	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.9
xfRFSpectrumDiagIdxCompanion1 RF IF index for 1st companion carrier (0 if no companion)	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.10
xfRFSpectrumDiagIdxCompanion2 RF IF index for 2nd companion carrier (0 if no companion)	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.11
xfRFSpectrumDiagIdxCompanion3 RF IF index for 3rd companion carrier (0 if no companion)	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.12
xfRFSpectrumDiagProgress Completed percentage of Spectrum Diagnostics scan	Unsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.193.81.3.4.3.1.6.1.13

Table of Spectrum Diagnostics scan results

xfRFSpectrumDiagResultEntry row .1.3.6.1.4.1.193.81.3.4.3.1.7.1

An entry in xfRFSpectrumDiagResultTable

Indexes

IF-MIBifIndex xfRFSpectrumDiagResultIndex

Column	Syntax	OID
xfRFSpectrumDiagResultIndex Spectrum Diagnostics Scan Result Index	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.7.1.1
xfRFSpectrumDiagResultRxFrequency Spectrum Diagnostics Scan Result Rx frequency in kHz	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.193.81.3.4.3.1.7.1.2
xfRFSpectrumDiagResultRxPower Spectrum Diagnostics Scan Result Rx Power value/10 dBm Domain: [-99.9 .. -20.0 dBm]	Integer32 Constraints: range: -999--200	.1.3.6.1.4.1.193.81.3.4.3.1.7.1.3

Table for Radio Link RAU managed objects.
Table indexed with ifIndex.

xfRfIfPowerEntry row .1.3.6.1.4.1.193.81.3.4.3.1.8.1

An entry in the xfRfIfPowerTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
xfRfSelectedMinOutputPower Minimum output power in dBm (selected by operator). Default value: 10 dBm.	RfOutputPowerr/w Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.1
xfRfSelectedMaxOutputPower Maximum output power in dBm (selected by operator). Default value: 10 dBm.	RfOutputPowerr/w Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.2
xfRfCurrentOutputPower Current output power in dBm. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.3
xfRfMinOutputPower Minimum output power in dBm (provided by RAU). 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.4
xfRfMaxOutputPower Maximum output power in dBm (provided by RAU). 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.5
xfRfAtpcTargetInputPowerFE ATPC target input power on Far End side. Default value: -30.	Integer32r/w Constraints: range: -99--30	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.6
xfRfCurrentInputPower RF input level. Value is in 1/10 dBm. Domain: [-20.0 .. -99.9 dBm].	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.7
xfRfMaxInputPowerLast7Days Maximum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.8
xfRfMinInputPowerLast7Days Minimum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.9
xfRfMaxInputPowerSinceReset Maximum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.10
xfRfMinInputPowerSinceReset Minimum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.11
xfRfInputPowerReset This object resets the registers for: - RF input power levels - input levels (i.e. RF power, MSE and XPI) in the next 7 days period of time.	Enumerationr/w Enumerated Values: 1 other 2 inputPowerNoReset 3 inputPowerReset	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.12
xfRfInputAlarmThreshold RF input level threshold. Default value: -93.	Integer32r/w Constraints: range: -99--30	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.13
xfRfOutputPower4QAM Output power for 4QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.14
xfRfOutputPower16QAM Output power for 16QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.15
xfRfOutputPower32QAM Output power for 32QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.16
xfRfOutputPower64QAM Output power for 64QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.17
xfRfOutputPower128QAM Output power for 128QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.18
xfRfOutputPower256QAM Output power for 256QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.19
xfRfOutputPower512QAM Output power for 512QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.20
xfRfOutputPower1024QAM Output power for 1024QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.21
xfRfOutputPower2048QAM Output power for 2048QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.22
xfRfOutputPower4096QAM Output power for 4096QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.23
xfRfMaxOutputPowerNotLimited Max output power in dBm that the RAU can give if it is not power supply limited. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.24
xfRfMaxOutputPowerPossible possible(2): max output power is possible. notPossible(3): max output power is not possible, due to power supply limitations.	Enumeration Enumerated Values: 1 other 2 possible 3 notPossible	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.25
xfRfMeanInputPower1m This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value.	Integer32 Constraints: range: -999--200 range: 0-0	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.26
xfRfMaxOutputPowerLast7Days This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.27
xfRfMinOutputPowerLast7Days This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.28
xfRfMaxOutputPowerSinceReset This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.29
xfRfMinOutputPowerSinceReset This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.	Integer32 Constraints: range: -100-45 range: 255-255	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.30
xfRfOutputPowerReset This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.	Enumerationr/w Enumerated Values: 1 other 2 outputPowerNoReset 3 outputPowerReset	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.31
xfRfAvailableOutputPowerType This object reports the output power capability of the RAU: - standardPower - highPower	Enumeration Enumerated Values: 1 other 2 standardPower 3 highPower	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.32
xfRfSelectedOutputPowerType This object allows setting the output power type: - standardPower - highPower default: standardPower(2) When the type is set to highPower(3) a HP license key is required. If the license key is not present the capacity i…	Enumerationr/w Enumerated Values: 1 other 2 standardPower 3 highPower	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.33
xfRfTaps This object allows setting the Traffic Aware Power Saving. Default: disabled(3)	Enumerationr/w Enumerated Values: 1 other 2 enabled 3 disabled 4 notAvailable	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.34
xfRfCurrentInputPowerSdcMain This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.35
xfRfCurrentInputPowerSdcDiv This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).	RfInputPower Type Constraints: range: -999..-200 range: 0 Description: RF Input power in dBm/10.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.36
xfRfOutputPower8192QAM Output power for 8192QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.37
xfRfOutputPower16384QAM Output power for 16384QAM. 255 indicates invalid value.	RfOutputPower Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.38
xfRfAtpcFallbackOutputPower This object sets output power (in dBm) in ATPCFallback mode, for radio contained in the Carrier Termination. 255 indicates invalid value.	RfOutputPowerr/w Type Constraints: range: -100..45 range: 255 Description: RF output power in dBm.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.39
xfRfAtpcFallbackEnable Enable/disable ATPCFallback.	ATPCFallbackEnabler/w Type Values: 1 other 2 disable 3 enable Description: ATPC fallback enable status.	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.40
xfRfAtpcFallbackTimer This object specifies how long the output power can be at (ATPC, MAX) before ATPC fallback is triggered. Default value: ETSI 15 min, ANSI 5 min.	Integer32r/w Constraints: range: 1-60	.1.3.6.1.4.1.193.81.3.4.3.1.8.1.41

Table for Radiolink point-to-point radios RF IF Cable Monitoring managed objects.
Table indexed with ifIndex.

xfRFIFCableMonitoringEntry row .1.3.6.1.4.1.193.81.3.4.3.1.9.1

An entry in the xfRFIFCableMonitoringTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
xfRFIFCMStatus This object manage IfCable Monitoring Status. Default value: disable(2). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.1
xfRFOutlierAgc This object manage IfCable Outlier Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.2
xfRFOutlierSetTh This object handles Set Threshold for Outlier Alarm. 3 = Default value (0.3). - To calculate threshold use the following formula: SetTh/10. Default value: 3 Near end access: read-write. Far end access: no access.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.3
xfRFOutlierCeaseTh This object handles Cease Threshold for Outlier Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 Near end access: read-write. Far end access: no access.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.4
xfRFRangeAgc This object manage IfCable Range Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.5
xfRFRangeSetTh This object handles Set Threshold for Range Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.6
xfRFRangeCeaseTh This object handles Cease Threshold for Range Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.7
xfRFStddevAgc This object manage IfCable Stddev Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.8
xfRFStddevSetTh This object handles Set Threshold for Stddev Alarm. 50 = Default value (5). - To calculate threshold use the following formula: SetTh/10. Default value: 50 (dB/10) Near end access: read-write. Far end access: no access.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.9
xfRFStddevCeaseTh This object handles Cease Threshold for Stddev Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no acces…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.10
xfRFDegradationAgc This object manage IfCable Degradation Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.11
xfRFDegradationSetTh This object handles Set Threshold for Degradation Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 (dB/10) Near end access: read-write. Far end access: no ac…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.12
xfRFDegradationCeaseTh This object handles Cease Threshold for Degradation Alarm. 1 = Default value (0.1). - To calculate threshold use the following formula: SetTh/10. Default value: 1 (dB/10) Near end access: read-write. Far end access: no …	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.13
xfRFMarginAgc This object manage IfCable Margin Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.14
xfRFMarginSetTh This object handles Set Threshold for Margin Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.15
xfRFMarginCeaseTh This object handles Cease Threshold for Margin Alarm. 60 = Default value (6). - To calculate threshold use the following formula: SetTh/10. Default value: 60 (dB/10) Near end access: read-write. Far end access: no acces…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.16
xfRFOutlierValue This object handles the value calculated on 24h for Outlier Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 Near end access: read-write. Far end access: no acces…	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.17
xfRFRangeValue This object handles the value calculated on 24h for Range Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: n…	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.18
xfRFStddevValue This object handles the value calculated on 24h for Stddev Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: …	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.19
xfRFDegradationValue This object handles the value calculated on 24h for Degradation Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end acc…	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.20
xfRFMarginValue This object handles the value calculated on 24h for Margin Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: …	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.21
xfRFOutlierTrigger This object manage IfCable Outlier Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.	Enumeration Enumerated Values: 1 other 2 noSetThreshold 3 setThreshold	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.22
xfRFRangeTrigger This object manage IfCable Range Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.	Enumeration Enumerated Values: 1 other 2 noSetThreshold 3 setThreshold	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.23
xfRFStddevTrigger This object manage IfCable Stddev Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.	Enumeration Enumerated Values: 1 other 2 noSetThreshold 3 setThreshold	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.24
xfRFDegradationTrigger This object manage IfCable Degradation Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.	Enumeration Enumerated Values: 1 other 2 noSetThreshold 3 setThreshold	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.25
xfRFMarginTrigger This object manage IfCable Margin Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.	Enumeration Enumerated Values: 1 other 2 noSetThreshold 3 setThreshold	.1.3.6.1.4.1.193.81.3.4.3.1.9.1.26

Table for SDC capabilities, setting and status.

xfSdcEntry row .1.3.6.1.4.1.193.81.3.4.3.1.10.1

An entry in the xfSdcTable.

Indexes

ENTITY-MIBentPhysicalIndex

Column	Syntax	OID
xfSdcCapability SDC capability, including both MMU and ODU.	Enumeration Enumerated Values: 1 other 2 sdcSupported 3 sdcNotSupported	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.1
xfSdcAdminStatus SDC Admin Status.	Enumerationr/w Enumerated Values: 1 other 2 sdcEnabled 3 sdcDisabled	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.2
xfSdcOperStatus SDC Oper Status.	Enumeration Enumerated Values: 1 other 2 sdcEnabled 3 sdcDisabled 4 sdcInProgress	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.3
xfSdcDadeControl SDC DADE procedure control.	Enumerationr/w Enumerated Values: 1 other 2 sdcDadeStart 3 sdcDadeAbort	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.4
xfSdcDadeStatus SDC DADE procedure status.	Enumeration Enumerated Values: 1 other 2 sdcCalibrated 3 sdcNotCalibrated 4 sdcCalInProgress 5 sdcCalMismatch	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.5
xfSdcPath SDC selected path (desired value).	Enumerationr/w Enumerated Values: 1 other 2 sdcAuto 3 sdcMain 4 sdcDiv	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.6
xfSdcOduDateTimeCalibration Date and time of the SDC DADE calibration for the ODU with serial number in xfSdcOduSerialNumber. Format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss] (ISO 8601).	SNMPv2-TCDisplayString Constraints: range: 0-255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.7
xfSdcOduSerialNumber Serial number of the ODU the current value of xfSdcOduDateTimeCalibration is referred to.	SNMPv2-TCDisplayString Constraints: range: 0-255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.8
xfSdcGain SDC gain in dB/10. Domain: [0.0 .. 3.0 dB].	Integer32 Constraints: range: 0-30	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.9
xfSdcActualPath SDC actual path (current value).	Enumeration Enumerated Values: 1 other 2 sdcAuto 3 sdcMain 4 sdcDiv	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.10
xfSdcDadeDelay DADE delay in nsec.	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.193.81.3.4.3.1.10.1.11