Wellfleet-CSMACD-MIB Table View

create/delete parameter, dflt = created

enable/disable parameter, dflt = enabled

line driver state variable, Not Present, Init, Down, Up

instance ID Slot, filled in by driver

instance ID Connector, filled in by driver. For the ASN
this attribute is an encoded value and is equal to
'module'*10 + 'connector'. Where 'module' is defined in
attribute 42 and 'connector' is defined in attribute 43
…

cct number for this line instance

bofl parameter, dflt = enabled

bofl parameter, dflt = 5. A value of zero has a special meaning.
When bofl tmo is zero, the line is killed as soon as the link down
down condition is determined.

mtu parameter, fixed

line MAC address, fixed - line driver fills in

Number of octets received without error

Number of frames received without error

Number of octets transmitted without error

Number of frames transmitted without error

Number of deferred transmissions

Number of late collisions

Number of excessive collisions

Number of frames transmitted larger than the MTU size
in wfCSMACDMtu

Number of internal buffer errors

Number of loss of carrier errors

Number of transmitter underflow errors

Number of receiver checksum errors

Number of receiver alignment errors

Number of receiver lack of resource errors

Number of frames received exceeding the MTU size
in wfCSMACDMtu.

Number of receiver overflow errors

Number of internal memory errors

Number of collision errors

Hardware filtering parameter.

Current Transmit Queue Length

Current Receive Queue Length

Number of frames clipped in driver's transmit routine due to transmit
congestion.

Number of packet buffer misses while attempting to replenish driver
receive ring.

Configured Transmit Queue Length. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero causes router based default values to be used. Values larger
than the compiled r…

Configured Receive Queue Length. Values other than zero over-ride
the router selected values. A value of zero has a special meaning.
Zero causes router based default values to be used. Values larger
than the compiled ri…

Enables special frame re-alignment in the Line Driver. Only needed when
4 ethernet interfaces are configured on a single slot. Only needed if
experiencing transmit underflow errors (wfCSMACDUfloTx). When this
attribut…

Number of non-optimally aligned frames queued to the driver for transmit.
This statistic does not indicate that any frames have been dropped. If
the ethernet I/O board is not a Quad Ethernet Link Module (QENET) or if it…

Logical line number associated with this driver entity.

Number of late collisions - found in QUICC Ethernet Rx Buffer Descriptors

Module number for ASN platform, filled in by driver. For non-ASN
platforms this attribute will not be used.

Actual connector number for ASN platform, filled in by
driver. For non-ASN platforms this attribute will not be used.

The value of SysUpTime at the time the interface entered it's current
operational state (UP state). SysUpTime is defined as the time (in
hundredths of a second) since the network management portion of the
system was la…

The instantaneous current length of the output packet queue (in packets).

counts the number of times the interrupt service routine
has been called

Counts the number of times the transmit routine
has been called

Counts the number of times RINT processing takes place
in the interrupt service routine.

Counts the number of times the transmit complete
processing takes place

Counts the number of times the transmit queue
has been shrinked in size due to the number of
tx clips exceeding the treshold

A count of successfully transmitted frames on a particular interface
for which transmission is inhibited by exactly one collision.

A count of successfully transmitted frames on a particular interface
for which transmission is inhibited by more than one collision.

A count of frames for which transmission on a particular interface fails
due to an internal MAC sublayer transmit error. A frame is only counted
by an instance of this object if it is not counted by the corresponding
i…

If NWay is configured, this attribute contains a value that uniquely
identifies the single capability that was agreed upon by the local and
remote interfaces. If NWay is not configured, this attribute describes
the spe…

This object contains an OBJECT IDENTIFIER which identifies the chipset used
to realize the interface. This object usually identifies the Medium Access
Control (MAC) chip.

A count of frames received on a particular interface with one or more
100Mb symbol errors detected.

A count of frames for which reception on a particular interface fails
due to an internal MAC sublayer receive error. A frame is only counted
by an instance of this object if it is not counted by the corresponding
insta…

This attribute will be enabled(1) if the interface supports different
speed configurations. If configurable speeds are not supported on the
interface, this attribute will be disabled(2). Creation of
wfCSMACDAutoNegEnt…

This attribute describes the number of times the hardware
has entered a state which required a flush of the RX FIFO.

This attribute describes the number of times the hardware
has entered a Tx Deadlock condition, and the software
intervenes to free up the lock.

bofl retries, dflt = 5

bofl tmo divisorr, dflt = 1

Special Turbo-BOFL debug mechanism to be used by Engineering
and Manufacturing only.
31-24 : TMO - period of breath (amount of time between
successive breaths of life)
23-16 : Number of packets per breath.
15-0 : …

IfTable Index for this line instance,
filled in by driver. For the BAC it is not the same
as the circuit number.

This attribute indicates the number of Flow Control
Pause frames transmitted.

This attribute indicates the number of Flow Control
Pause frames received.

This attribute indicates the number of Control
frames received that were not pause frames.

Flow control enable/disable parameter, dflt = enabled

This attribute indicates flow control pause time in slots.

Tx Pause 0 frame generation enable/disable parameter, dflt = enabled.

User-selected line speed for DSQMS client

create/delete parameter, dflt = created

instance ID Slot, filled in by driver

instance ID Connector, filled in by driver. For the ASN
this attribute is an encoded value and is equal to
'module'*10 + 'connector'. Where 'module' is defined in
attribute 42 and 'connector' is defined in attribute 43
…

This value indicates the configured speed of the local interface.
This parameter allows configuration of a specific speed and duplex
setting, or allows configuration/enabling of Auto Negotiation/NWay.
Selecting a specif…

This value indicates whether the remote end of the link is operating
Auto Negotiation signaling or not. It shall take the value detected if,
during the previous link negotiation, FLP bursts were received from the
remot…

This value indicates whether Auto Negotiation signaling is in progress
or has completed.
NOTE: This parameter is only valid if SpeedSelect is configured for NWay.

Writing any value to this attribute forces Auto Negotiation to begin link
re-negotiation. This action has no effect if Auto Negotiation signaling
is disabled.
NOTE: This parameter is only valid if SpeedSelect is configu…

This is a GAUGE because this attribute is 32-bit unsigned, non-increasing
A value that uniquely identifies the set of capabilities of the LOCAL Auto
Negotiation entity. The value is a sum which initially takes the value…

This is a GAUGE because this attribute is 32-bit unsigned, non-increasing
A successful set operation will result in immediate link re-negotiation if
AutoNegAdminState is enabled. A value that uniquely identifies the se…

This is a GAUGE because this attribute is 32-bit unsigned, non-increasing
A value that uniquely identifies the set of capabilities of the REMOTE Auto
Negotiation entity. The value is a sum which initially takes the valu…