A Sonus SBC Application service was restarted.

System detected a problem during previous boot cycle, active partition has switched automatically. Suggested action - backup the configuration and re-apply the upgrade to the currently inactive partition.

While booting, one of the partition could not be mounted. Likely a eUSB corruption. Contact Sonus TAC with the information in this alarm.

Failed to set active partition.Contact Sonus TAC with the information in this alarm.

Attempt to auto repair boot parmeters failed.Contact Sonus TAC with the information in this alarm.

Boot parameter mismatch was detected.Attempting to auto repair.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

Power-on self test failure.

System up after planned restart.

System up after unplanned restart.

No response to seizure.

Remote end did not back off in glare.

Wink expected, did not arrive.

Event of off-hook did not produce dial tone as expected.

CAS signaling group disabled.

Call attempted but CAS feature is not enabled. This alarm is cleared by CAS license enabled event.

License manager notify CAS that license is enabled.

Wink failure had occurred, but wink is received now.

No Dial Tone was received, but Dial Tone is received now.

No Response to seizure was received, but Response is received now.

Invalid character(s) removed, correct issue and delete warning.

Invalid character(s) removed, correct issue and delete warning.

CAS signaling group enabled.

CAS-R2 CD Bits are mismatched.

CAS-R2 CD Bits are now matching.

Network glare occured on this interface.

Config validation failure during startup. Please check the configuration.

A Card was detected with invalid Card ID EEPROM contents (failed CRC-CCITT check). Suggested action - provide the entire alarm message including the numbers at the end to Sonus TAC for further assistance.

During Line Card activation, a Card Fault was detected after power was applied to the card. The Card will remain out-of-service.  Suggested action - reboot system. If issue persists, contact Sonus TAC with the alarm information.

A Card was detected which can be identified, but the Sonus SBC system software is unable to support. The Card will remain out-of-service. Suggested action - reboot system. If issue persists, contact Sonus TAC with the alarm information.

A Power supply module has indicated a failure of input power. The Sonus SBC System has lost Power Supply redundancy. Suggested action - Verify that the power cable is connected and that the PS is functioning properly.

A Power Supply module has indicated that input power has been restored. This event clears the 'Power Supply Input Failure' Alarm.

A Power Supply module has indicated a failure of output power. The Sonus SBC System has lost Power Supply redundancy. Suggested action - Verify that the PS is functioning properly.

Check the System tab to find the Fan ID of the failed fan. Contact Sonus TAC with this information.

Check the System tab to find the Fan ID's of the failed fans. Contact Sonus TAC with this information.

The temperature sensors have indicated that the system is running warm (65°C threshold).

The temperature sensors have indicated that the system is no longer running warm (55°C threshold). This event clears the 'System Temperature Warm' Alarm.

The temperature sensors have indicated that system is running hot.

The temperature sensors have indicated that the system is no longer running hot (65°C threshold). This event clears the 'System Temperature Hot' Alarm.

License of the node has expired, all the licensed features would fail to work. Contact Sonus Enterprise Sales.

License of the node will expire in 2 weeks.

New License is applied on the node.

Either an invalid key is used, or the license key applies to a different node, or the license key expiry is past the present date. Contact Sonus Sales to obtain a new license.

The alarm is generated when the required license is not available.  Check the number of licensed SIP or TDM channels, the number of SIP registrations, SBA, Transcoding or AD. Suggested action - obtain license for missing functionality.

ASM system can not be reached, system is down. Check whether the ASM is rebooting.

Clears alarm 'ASM Unreachable'.

ASM system was previously unreachable, but has come up. This alarm doesn't autoclear so the user can investigate the cause, but the system should be working correctly now.

ASM services are not running, calls through the ASM cannot be placed.

Clears alarm 'ASM Services Not Running'.

ASM Services Recovered.

The system attempted to restart a failed service on the ASM, service did not start successfully. User interaction is required.

This event is set when the SBA communication system is first established, and usually indicates that the Application Solution Module (ASM) has finished booting. It should come up at system startup, it may come again if the ASM hardware is rebooted.

A planned or deliberate shut down is taking place on the Application Solution Module (ASM).

Ethernet port specified has lost link. Source Instance: Eth0/Eth1 via SBA Monitor.

Ethernet port specific has recovered link.

The ASM and Sonus SBC IP interfaces are in different subnets and cannot communicate.

The ASM and Sonus SBC IP interfaces are in the same subnet and can now communicate.

There is an action set table number/name that should be printed with this event.