RFC1382-MIB Table View

This table contains the administratively
set configuration parameters for an X.25
Packet Level Entity (PLE).
          
Most of the objects in this table have
corresponding objects in the x25OperTable.
This table contains the values as last set
by the administrator.  The x25OperTable
contains the values actually in use by an
X.25 PLE.
          
Changing an administrative value may or may
not change a current operating value.  The
operating value may not change until the
interface is restarted.  Some
implementations may change the values
immediately upon changing the administrative
table.  All implementations are required to
load the values from the administrative
table when initializing a PLE.

x25AdmnEntry row .1.3.6.1.2.1.10.5.1.1

Entries of x25AdmnTable.

Indexes

x25AdmnIndex

Column	Syntax	OID
x25AdmnIndexmandatory The ifIndex value for the X.25 Interface.	RFC1381-MIBIfIndexType Type Constraints: range: 1..2147483647	.1.3.6.1.2.1.10.5.1.1.1
x25AdmnInterfaceModemandatory Identifies DCE/DTE mode in which the interface operates. A value of dxe indicates the mode will be determined by XID negotiation.	Enumerationr/w Enumerated Values: 1 dte 2 dce 3 dxe	.1.3.6.1.2.1.10.5.1.1.2
x25AdmnMaxActiveCircuitsmandatory The maximum number of circuits this PLE can support; including PVCs.	Integer32r/w Constraints: range: 0-4096	.1.3.6.1.2.1.10.5.1.1.3
x25AdmnPacketSequencingmandatory The modulus of the packet sequence number space.	Enumerationr/w Enumerated Values: 1 modulo8 2 modulo128	.1.3.6.1.2.1.10.5.1.1.4
x25AdmnRestartTimermandatory The T20 restart timer in milliseconds.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.5
x25AdmnCallTimermandatory The T21 Call timer in milliseconds.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.6
x25AdmnResetTimermandatory The T22 Reset timer in milliseconds.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.7
x25AdmnClearTimermandatory The T23 Clear timer in milliseconds.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.8
x25AdmnWindowTimermandatory The T24 window status transmission timer in milliseconds. A value of 2147483647 indicates no window timer in use.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.9
x25AdmnDataRxmtTimermandatory The T25 data retransmission timer in milliseconds. A value of 2147483647 indicates no data retransmission timer in use.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.10
x25AdmnInterruptTimermandatory The T26 interrupt timer in milliseconds. A value of 2147483647 indicates no interrupt timer in use.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.11
x25AdmnRejectTimermandatory The T27 Reject retransmission timer in milliseconds. A value of 2147483647 indicates no reject timer in use.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.12
x25AdmnRegistrationRequestTimermandatory The T28 registration timer in milliseconds. A value of 2147483647 indicates no registration timer in use.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.13
x25AdmnMinimumRecallTimermandatory Minimum time interval between unsuccessful call attempts in milliseconds.	RFC1381-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.1.1.14
x25AdmnRestartCountmandatory The R20 restart retransmission count.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.1.1.15
x25AdmnResetCountmandatory The r22 Reset retransmission count.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.1.1.16
x25AdmnClearCountmandatory The r23 Clear retransmission count.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.1.1.17
x25AdmnDataRxmtCountmandatory The R25 Data retransmission count. This value is irrelevant if the x25AdmnDataRxmtTimer indicates no timer in use.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.1.1.18
x25AdmnRejectCountmandatory The R27 reject retransmission count. This value is irrelevant if the x25AdmnRejectTimer indicates no timer in use.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.1.1.19
x25AdmnRegistrationRequestCountmandatory The R28 Registration retransmission Count. This value is irrelevant if the x25AdmnRegistrationRequestTimer indicates no timer in use.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.1.1.20
x25AdmnNumberPVCsmandatory The number of PVC configured for this PLE. The PVCs use channel numbers from 1 to this number.	Integer32r/w Constraints: range: 0-4096	.1.3.6.1.2.1.10.5.1.1.21
x25AdmnDefCallParamIdmandatory This identifies the instance of the x25CallParmIndex for the entry in the x25CallParmTable which contains the default call parameters for this PLE.	ObjectIdentifierr/w	.1.3.6.1.2.1.10.5.1.1.22
x25AdmnLocalAddressmandatory The local address for this PLE subnetwork. A zero length address maybe returned by PLEs that only support PVCs.	X121Addressr/w Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.1.1.23
x25AdmnProtocolVersionSupportedmandatory Identifies the version of the X.25 protocol this interface should support. Object identifiers for common versions are defined below in the x25ProtocolVersion subtree.	ObjectIdentifierr/w	.1.3.6.1.2.1.10.5.1.1.24

The operation parameters in use by the X.25
PLE.

x25OperEntry row .1.3.6.1.2.1.10.5.2.1

Entries of x25OperTable.

Indexes

x25OperIndex

Column	Syntax	OID
x25OperIndexmandatory The ifIndex value for the X.25 interface.	RFC1381-MIBIfIndexType Type Constraints: range: 1..2147483647	.1.3.6.1.2.1.10.5.2.1.1
x25OperInterfaceModemandatory Identifies DCE/DTE mode in which the interface operates. A value of dxe indicates the role will be determined by XID negotiation at the Link Layer and that negotiation has not yet taken place.	Enumeration Enumerated Values: 1 dte 2 dce 3 dxe	.1.3.6.1.2.1.10.5.2.1.2
x25OperMaxActiveCircuitsmandatory Maximum number of circuits this PLE can support.	Integer32 Constraints: range: 0-4096	.1.3.6.1.2.1.10.5.2.1.3
x25OperPacketSequencingmandatory The modulus of the packet sequence number space.	Enumeration Enumerated Values: 1 modulo8 2 modulo128	.1.3.6.1.2.1.10.5.2.1.4
x25OperRestartTimermandatory The T20 restart timer in milliseconds.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.5
x25OperCallTimermandatory The T21 Call timer in milliseconds.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.6
x25OperResetTimermandatory The T22 Reset timer in milliseconds.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.7
x25OperClearTimermandatory The T23 Clear timer in milliseconds.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.8
x25OperWindowTimermandatory The T24 window status transmission timer milliseconds. A value of 2147483647 indicates no window timer in use.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.9
x25OperDataRxmtTimermandatory The T25 Data Retransmission timer in milliseconds. A value of 2147483647 indicates no data retransmission timer in use.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.10
x25OperInterruptTimermandatory The T26 Interrupt timer in milliseconds. A value of 2147483647 indicates interrupts are not being used.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.11
x25OperRejectTimermandatory The T27 Reject retransmission timer in milliseconds. A value of 2147483647 indicates no reject timer in use.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.12
x25OperRegistrationRequestTimermandatory The T28 registration timer in milliseconds. A value of 2147483647 indicates no registration timer in use.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.13
x25OperMinimumRecallTimermandatory Minimum time interval between unsuccessful call attempts in milliseconds.	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.2.1.14
x25OperRestartCountmandatory The R20 restart retransmission count.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.2.1.15
x25OperResetCountmandatory The r22 Reset retransmission count.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.2.1.16
x25OperClearCountmandatory The r23 Clear retransmission count.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.2.1.17
x25OperDataRxmtCountmandatory The R25 Data retransmission count. This value is undefined if the x25OperDataRxmtTimer indicates no timer in use.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.2.1.18
x25OperRejectCountmandatory The R27 reject retransmission count. This value is undefined if the x25OperRejectTimer indicates no timer in use.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.2.1.19
x25OperRegistrationRequestCountmandatory The R28 Registration retransmission Count. This value is undefined if the x25OperREgistrationRequestTimer indicates no timer in use.	Integer32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.5.2.1.20
x25OperNumberPVCsmandatory The number of PVC configured for this PLE. The PVCs use channel numbers from 1 to this number.	Integer32 Constraints: range: 0-4096	.1.3.6.1.2.1.10.5.2.1.21
x25OperDefCallParamIdmandatory This identifies the instance of the x25CallParmIndex for the entry in the x25CallParmTable that contains the default call parameters for this PLE.	ObjectIdentifier	.1.3.6.1.2.1.10.5.2.1.22
x25OperLocalAddressmandatory The local address for this PLE subnetwork. A zero length address maybe returned by PLEs that only support PVCs.	X121Address Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.2.1.23
x25OperDataLinkIdmandatory This identifies the instance of the index object in the first table of the most device specific MIB for the interface used by this PLE.	ObjectIdentifier	.1.3.6.1.2.1.10.5.2.1.24
x25OperProtocolVersionSupportedmandatory Identifies the version of the X.25 protocol this interface supports. Object identifiers for common versions are defined below in the x25ProtocolVersion subtree.	ObjectIdentifier	.1.3.6.1.2.1.10.5.2.1.25

Statistics information about this X.25
PLE.

x25StatEntry row .1.3.6.1.2.1.10.5.3.1

Entries of the x25StatTable.

Indexes

x25StatIndex

Column	Syntax	OID
x25StatIndexmandatory The ifIndex value for the X.25 interface.	RFC1381-MIBIfIndexType Type Constraints: range: 1..2147483647	.1.3.6.1.2.1.10.5.3.1.1
x25StatInCallsmandatory The number of incoming calls received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.2
x25StatInCallRefusalsmandatory The number of incoming calls refused. This includes calls refused by the PLE and by higher layers. This also includes calls cleared because of restricted fast select.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.3
x25StatInProviderInitiatedClearsmandatory The number of clear requests with a cause code other than DTE initiated.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.4
x25StatInRemotelyInitiatedResetsmandatory The number of reset requests received with cause code DTE initiated.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.5
x25StatInProviderInitiatedResetsmandatory The number of reset requests received with cause code other than DTE initiated.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.6
x25StatInRestartsmandatory The number of remotely initiated (including provider initiated) restarts experienced by the PLE excluding the restart associated with bringing up the PLE interface. This only counts restarts received when the PLE alrea…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.7
x25StatInDataPacketsmandatory The number of data packets received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.8
x25StatInAccusedOfProtocolErrorsmandatory The number of packets received containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.9
x25StatInInterruptsmandatory The number of interrupt packets received by the PLE or over the PVC/VC.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.10
x25StatOutCallAttemptsmandatory The number of calls attempted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.11
x25StatOutCallFailuresmandatory The number of call attempts which failed. This includes calls that were cleared because of restrictive fast select.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.12
x25StatOutInterruptsmandatory The number of interrupt packets send by the PLE or over the PVC/VC.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.13
x25StatOutDataPacketsmandatory The number of data packets sent by this PLE.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.14
x25StatOutgoingCircuitsmandatory The number of active outgoing circuits. This includes call requests sent but not yet confirmed. This does not count PVCs.	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.15
x25StatIncomingCircuitsmandatory The number of active Incoming Circuits. This includes call indications received but not yet acknowledged. This does not count PVCs.	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.16
x25StatTwowayCircuitsmandatory The number of active two-way Circuits. This includes call requests sent but not yet confirmed. This does not count PVCs.	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.17
x25StatRestartTimeoutsmandatory The number of times the T20 restart timer expired.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.18
x25StatCallTimeoutsmandatory The number of times the T21 call timer expired.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.19
x25StatResetTimeoutsmandatory The number of times the T22 reset timer expired.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.20
x25StatClearTimeoutsmandatory The number of times the T23 clear timer expired.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.21
x25StatDataRxmtTimeoutsmandatory The number of times the T25 data timer expired.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.22
x25StatInterruptTimeoutsmandatory The number of times the T26 interrupt timer expired.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.23
x25StatRetryCountExceededsmandatory The number of times a retry counter was exhausted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.24
x25StatClearCountExceededsmandatory The number of times the R23 clear count was exceeded.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.3.1.25

These objects contain information about the
channel number configuration in an X.25 PLE.
These values are the configured values.
changes in these values after the interfaces
has started may not be reflected in the
operating PLE.

x25ChannelEntry row .1.3.6.1.2.1.10.5.4.1

Entries of x25ChannelTable.

Indexes

x25ChannelIndex

Column	Syntax	OID
x25ChannelIndexmandatory The ifIndex value for the X.25 Interface.	RFC1381-MIBIfIndexType Type Constraints: range: 1..2147483647	.1.3.6.1.2.1.10.5.4.1.1
x25ChannelLICmandatory Lowest Incoming channel.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.4.1.2
x25ChannelHICmandatory Highest Incoming channel. A value of zero indicates no channels in this range.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.4.1.3
x25ChannelLTCmandatory Lowest Two-way channel.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.4.1.4
x25ChannelHTCmandatory Highest Two-way channel. A value of zero indicates no channels in this range.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.4.1.5
x25ChannelLOCmandatory Lowest outgoing channel.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.4.1.6
x25ChannelHOCmandatory Highest outgoing channel. A value of zero indicates no channels in this range.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.4.1.7

These objects contain general information
about a specific circuit of an X.25 PLE.

x25CircuitEntry row .1.3.6.1.2.1.10.5.5.1

Entries of x25CircuitTable.

Indexes

x25CircuitIndex x25CircuitChannel

Column	Syntax	OID
x25CircuitIndexmandatory The ifIndex value for the X.25 Interface.	RFC1381-MIBIfIndexType Type Constraints: range: 1..2147483647	.1.3.6.1.2.1.10.5.5.1.1
x25CircuitChannelmandatory The channel number for this circuit.	Integer32 Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.5.1.2
x25CircuitStatusmandatory This object reports the current status of the circuit. An existing instance of this object can only be set to startClear, startPvcResetting, or invalid. An instance with the value calling or open can onl…	Enumerationr/w Enumerated Values: 1 invalid 2 closed 3 calling 4 open 5 clearing 6 pvc 7 pvcResetting 8 startClear 9 startPvcResetting 10 other	.1.3.6.1.2.1.10.5.5.1.3
x25CircuitEstablishTimemandatory The value of sysUpTime when the channel was associated with this circuit. For outgoing SVCs, this is the time the first call packet was sent. For incoming SVCs, this is the time the call indication was received. For …	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.4
x25CircuitDirectionmandatory The direction of the call that established this circuit.	Enumerationr/w Enumerated Values: 1 incoming 2 outgoing 3 pvc	.1.3.6.1.2.1.10.5.5.1.5
x25CircuitInOctetsmandatory The number of octets of user data delivered to upper layer.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.6
x25CircuitInPdusmandatory The number of PDUs received for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.7
x25CircuitInRemotelyInitiatedResetsmandatory The number of Resets received for this circuit with cause code of DTE initiated.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.8
x25CircuitInProviderInitiatedResetsmandatory The number of Resets received for this circuit with cause code other than DTE initiated.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.9
x25CircuitInInterruptsmandatory The number of interrupt packets received for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.10
x25CircuitOutOctetsmandatory The number of octets of user data sent for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.11
x25CircuitOutPdusmandatory The number of PDUs sent for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.12
x25CircuitOutInterruptsmandatory The number of interrupt packets sent on this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.13
x25CircuitDataRetransmissionTimeoutsmandatory The number of times the T25 data retransmission timer expired for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.14
x25CircuitResetTimeoutsmandatory The number of times the T22 reset timer expired for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.15
x25CircuitInterruptTimeoutsmandatory The number of times the T26 Interrupt timer expired for this circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.5.1.16
x25CircuitCallParamIdmandatory This identifies the instance of the x25CallParmIndex for the entry in the x25CallParmTable which contains the call parameters in use with this circuit. The entry referenced must contain the values that are currently in…	ObjectIdentifierr/w	.1.3.6.1.2.1.10.5.5.1.17
x25CircuitCalledDteAddressmandatory For incoming calls, this is the called address from the call indication packet. For outgoing calls, this is the called address from the call confirmation packet. This will be zero length for PVCs.	X121Addressr/w Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.5.1.18
x25CircuitCallingDteAddressmandatory For incoming calls, this is the calling address from the call indication packet. For outgoing calls, this is the calling address from the call confirmation packet. This will be zero length for PVCs.	X121Addressr/w Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.5.1.19
x25CircuitOriginallyCalledAddressmandatory For incoming calls, this is the address in the call Redirection or Call Deflection Notification facility if the call was deflected or redirected, otherwise it will be called address from the call indication packet. For…	X121Addressr/w Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.5.1.20
x25CircuitDescrmandatory A descriptive string associated with this circuit. This provides a place for the agent to supply any descriptive information it knows about the use or owner of the circuit. The agent may return the process identifier …	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.2.1.10.5.5.1.21

A table of entries about closed circuits.
Entries must be made in this table whenever
circuits are closed and the close request or
close indication packet contains a clearing
cause other than DTE Originated or a
Diagnostic code field other than Higher
Layer Initiated disconnection-normal.  An
agent may optionally make entries for normal
closes (to record closing facilities or
          
other information).
          
Agents will delete the oldest entry in the
table when adding a new entry would exceed
agent resources.  Agents are required to
keep the last entry put in the table and may
keep more entries.  The object
x25OperClearEntriesGranted returns the
maximum number of entries kept in the
table.

x25ClearedCircuitEntry row .1.3.6.1.2.1.10.5.8.1

Information about a cleared circuit.

Indexes

x25ClearedCircuitIndex

Column	Syntax	OID
x25ClearedCircuitIndexmandatory An index that uniquely distinguishes one entry in the clearedCircuitTable from another. This index will start at 2147483647 and will decrease by one for each new entry added to the table. Upon reaching one, the index …	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.8.1.1
x25ClearedCircuitPleIndexmandatory The value of ifIndex for the PLE which cleared the circuit that created the entry.	RFC1381-MIBIfIndexType Type Constraints: range: 1..2147483647	.1.3.6.1.2.1.10.5.8.1.2
x25ClearedCircuitTimeEstablishedmandatory The value of sysUpTime when the circuit was established. This will be the same value that was in the x25CircuitEstablishTime for the circuit.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.8.1.3
x25ClearedCircuitTimeClearedmandatory The value of sysUpTime when the circuit was cleared. For locally initiated clears, this will be the time when the clear confirmation was received. For remotely initiated clears, this will be the time wh…	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.8.1.4
x25ClearedCircuitChannelmandatory The channel number for the circuit that was cleared.	Integer32 Constraints: range: 0-4095	.1.3.6.1.2.1.10.5.8.1.5
x25ClearedCircuitClearingCausemandatory The Clearing Cause from the clear request or clear indication packet that cleared the circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.10.5.8.1.6
x25ClearedCircuitDiagnosticCodemandatory The Diagnostic Code from the clear request or clear indication packet that cleared the circuit.	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.10.5.8.1.7
x25ClearedCircuitInPdusmandatory The number of PDUs received on the circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.8.1.8
x25ClearedCircuitOutPdusmandatory The number of PDUs transmitted on the circuit.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.5.8.1.9
x25ClearedCircuitCalledAddressmandatory The called address from the cleared circuit.	X121Address Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.8.1.10
x25ClearedCircuitCallingAddressmandatory The calling address from the cleared circuit.	X121Address Type Constraints: range: 0..17	.1.3.6.1.2.1.10.5.8.1.11
x25ClearedCircuitClearFacilitiesmandatory The facilities field from the clear request or clear indication packet that cleared the circuit. A size of zero indicates no facilities were present.	OctetString Constraints: range: 0-109	.1.3.6.1.2.1.10.5.8.1.12

These objects contain the parameters that
can be varied between X.25 calls.  The
entries in this table are independent of the
PLE.  There exists only one of these tables
for the entire system.  The indexes for the
entries are independent of any PLE or any
circuit.  Other tables reference entries in
this table.  Entries in this table can be
used for default PLE parameters, for
parameters to use to place/answer a call,
for the parameters currently in use for a
circuit, or parameters that were used by a
circuit.
          
The number of references to a given set of
parameters can be found in the
x25CallParmRefCount object sharing the same
instance identifier with the parameters.
The value of this reference count also
affects the access of the objects in this
table.  An object in this table with the
same instance identifier as the instance
identifier of an x25CallParmRefCount must be
consider associated with that reference
count.  An object with an associated
reference count of zero can be written (if
its ACCESS clause allows it).  An object
with an associated reference count greater
than zero can not be written (regardless of
the ACCESS clause).  This ensures that a set
of call parameters being referenced from
another table can not be modified or changed
in a ways inappropriate for continued use by
that table.

x25CallParmEntry row .1.3.6.1.2.1.10.5.9.1

Entries of x25CallParmTable.

Indexes

x25CallParmIndex

Column	Syntax	OID
x25CallParmIndexmandatory A value that distinguishes this entry from another entry. Entries in this table are referenced from other objects which identify call parameters. It is impossible to know which other objects in the MIB r…	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.9.1.1
x25CallParmStatusmandatory The status of this call parameter entry. See RFC 1271 for details of usage.	RFC1271-MIBEntryStatusr/w Type Values: 1 valid 2 createRequest 3 underCreation 4 invalid	.1.3.6.1.2.1.10.5.9.1.2
x25CallParmRefCountmandatory The number of references know by a management station to exist to this set of call parameters. This is the number of other objects that have returned a value of, and will return a value of, the index for this set of ca…	RFC1381-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.10.5.9.1.3
x25CallParmInPacketSizemandatory The maximum receive packet size in octets for a circuit. A size of zero for a circuit means use the PLE default size. A size of zero for the PLE means use a default size of 128.	Integer32r/w Constraints: range: 0-4096	.1.3.6.1.2.1.10.5.9.1.4
x25CallParmOutPacketSizemandatory The maximum transmit packet size in octets for a circuit. A size of zero for a circuit means use the PLE default size. A size of zero for the PLE default means use a default size of 128.	Integer32r/w Constraints: range: 0-4096	.1.3.6.1.2.1.10.5.9.1.5
x25CallParmInWindowSizemandatory The receive window size for a circuit. A size of zero for a circuit means use the PLE default size. A size of zero for the PLE default means use 2.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.2.1.10.5.9.1.6
x25CallParmOutWindowSizemandatory The transmit window size for a circuit. A size of zero for a circuit means use the PLE default size. A size of zero for the PLE default means use 2.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.2.1.10.5.9.1.7
x25CallParmAcceptReverseChargingmandatory An enumeration defining if the PLE will accept or refuse charges. A value of default for a circuit means use the PLE default value. A value of neverAccept is only used for the PLE default and indicates the PLE will ne…	Enumerationr/w Enumerated Values: 1 default 2 accept 3 refuse 4 neverAccept	.1.3.6.1.2.1.10.5.9.1.8
x25CallParmProposeReverseChargingmandatory An enumeration defining if the PLE should propose reverse or local charging. The value of default for a circuit means use the PLE default. The value of default for the PLE default means use local.	Enumerationr/w Enumerated Values: 1 default 2 reverse 3 local	.1.3.6.1.2.1.10.5.9.1.9
x25CallParmFastSelectmandatory Expresses preference for use of fast select facility. The value of default for a circuit is the PLE default. A value of default for the PLE means noFastSelect. A value of noFastSelect or noRestrictedFa…	Enumerationr/w Enumerated Values: 1 default 2 notSpecified 3 fastSelect 4 restrictedFastResponse 5 noFastSelect 6 noRestrictedFastResponse	.1.3.6.1.2.1.10.5.9.1.10
x25CallParmInThruPutClasSizemandatory The incoming throughput class to negotiate. A value of tcDefault for a circuit means use the PLE default. A value of tcDefault for the PLE default means tcNone. A value of tcNone means do not negotiate throughtput cla…	Enumerationr/w Enumerated Values: 1 tcReserved1 2 tcReserved2 3 tc75 4 tc150 5 tc300 6 tc600 7 tc1200 8 tc2400 9 tc4800 10 tc9600 11 tc19200 12 tc48000 13 tc64000 14 tcReserved14 15 tcReserved15 16 tcReserved0 17 tcNone 18 tcDefault	.1.3.6.1.2.1.10.5.9.1.11
x25CallParmOutThruPutClasSizemandatory The outgoing throughput class to negotiate. A value of tcDefault for a circuit means use the PLE default. A value of tcDefault for the PLE default means use tcNone. A value of tcNone means do not negotiate throughtput…	Enumerationr/w Enumerated Values: 1 tcReserved1 2 tcReserved2 3 tc75 4 tc150 5 tc300 6 tc600 7 tc1200 8 tc2400 9 tc4800 10 tc9600 11 tc19200 12 tc48000 13 tc64000 14 tcReserved14 15 tcReserved15 16 tcReserved0 17 tcNone 18 tcDefault	.1.3.6.1.2.1.10.5.9.1.12
x25CallParmCugmandatory The Closed User Group to specify. This consists of two or four octets containing the characters 0 through 9. A zero length string indicates no facility requested. A string length of three containing the characters DE…	OctetStringr/w Constraints: range: 0-4	.1.3.6.1.2.1.10.5.9.1.13
x25CallParmCugoamandatory The Closed User Group with Outgoing Access to specify. This consists of two or four octets containing the characters 0 through 9. A string length of three containing the characters DEF for a circuit means use the PLE …	OctetStringr/w Constraints: range: 0-4	.1.3.6.1.2.1.10.5.9.1.14
x25CallParmBcugmandatory The Bilateral Closed User Group to specify. This consists of two octets containing the characters 0 through 9. A string length of three containing the characters DEF for a circuit means use the PLE default (the PLE def…	OctetStringr/w Constraints: range: 0-3	.1.3.6.1.2.1.10.5.9.1.15
x25CallParmNuimandatory The Network User Identifier facility. This is binary value to be included immediately after the length field. The PLE will supply the length octet. A zero length string indicates no facility requested. This value is…	OctetStringr/w Constraints: range: 0-108	.1.3.6.1.2.1.10.5.9.1.16
x25CallParmChargingInfomandatory The charging Information facility. A value of default for a circuit means use the PLE default. The value of default for the default PLE parameters means use noFacility. The value of noFacility means do not include a f…	Enumerationr/w Enumerated Values: 1 default 2 noFacility 3 noChargingInfo 4 chargingInfo	.1.3.6.1.2.1.10.5.9.1.17
x25CallParmRpoamandatory The RPOA facility. The octet string contains n * 4 sequences of the characters 0-9 to specify a facility with n entries. The octet string containing the 3 characters DEF for a circuit specifies use of the PLE default (…	OctetStringr/w Constraints: range: 0-108	.1.3.6.1.2.1.10.5.9.1.18
x25CallParmTrnstDlymandatory The Transit Delay Selection and Indication value. A value of 65536 indicates no facility requested. A value of 65537 for a circuit means use the PLE default (the PLE default parameters entry may not use…	Integer32r/w Constraints: range: 0-65537	.1.3.6.1.2.1.10.5.9.1.19
x25CallParmCallingExtmandatory The Calling Extension facility. This contains one of the following: A sequence of hex digits with the value to be put in the facility. These digits will be converted to binary by the agent and put in the…	OctetStringr/w Constraints: range: 0-40	.1.3.6.1.2.1.10.5.9.1.20
x25CallParmCalledExtmandatory The Called Extension facility. This contains one of the following: A sequence of hex digits with the value to be put in the facility. These digits will be converted to binary by the agent and put in the…	OctetStringr/w Constraints: range: 0-40	.1.3.6.1.2.1.10.5.9.1.21
x25CallParmInMinThuPutClsmandatory The minimum input throughput Class. A value of 16 for a circuit means use the PLE default (the PLE parameters entry may not use this value). A value of 17 indicates no facility requested.	Integer32r/w Constraints: range: 0-17	.1.3.6.1.2.1.10.5.9.1.22
x25CallParmOutMinThuPutClsmandatory The minimum output throughput Class. A value of 16 for a circuit means use the PLE default (the PLE parameters entry may not use this value). A value of 17 indicates no facility requested.	Integer32r/w Constraints: range: 0-17	.1.3.6.1.2.1.10.5.9.1.23
x25CallParmEndTrnsDlymandatory The End-to-End Transit Delay to negotiate. An octet string of length 2, 4, or 6 contains the facility encoded as specified in ISO/IEC 8208 section 15.3.2.4. An octet string of length 3 containing the thr…	OctetStringr/w Constraints: range: 0-6	.1.3.6.1.2.1.10.5.9.1.24
x25CallParmPrioritymandatory The priority facility to negotiate. The octet string encoded as specified in ISO/IEC 8208 section 15.3.2.5. A zero length string indicates no facility requested. The entry for the PLE default parameters must be zero …	OctetStringr/w Constraints: range: 0-6	.1.3.6.1.2.1.10.5.9.1.25
x25CallParmProtectionmandatory A string contains the following: A hex string containing the value for the protection facility. This will be converted from hex to the octets actually in the packet by the agent. The agent will supply the length field…	OctetStringr/w Constraints: range: 0-108	.1.3.6.1.2.1.10.5.9.1.26
x25CallParmExptDatamandatory The Expedited Data facility to negotiate. A value of default for a circuit means use the PLE default value. The entry for the PLE default parameters may not have the value default.	Enumerationr/w Enumerated Values: 1 default 2 noExpeditedData 3 expeditedData	.1.3.6.1.2.1.10.5.9.1.27
x25CallParmUserDatamandatory The call user data as placed in the packet. A zero length string indicates no call user data. If both the circuit call parameters and the PLE default have call user data defined, the data from the circuit call paramete…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.2.1.10.5.9.1.28
x25CallParmCallingNetworkFacilitiesmandatory The calling network facilities. The facilities are encoded here exactly as encoded in the call packet. These facilities do not include the marker facility code. A zero length string in th…	OctetStringr/w Constraints: range: 0-108	.1.3.6.1.2.1.10.5.9.1.29
x25CallParmCalledNetworkFacilitiesmandatory The called network facilities. The facilities are encoded here exactly as encoded in the call packet. These facilities do not include the marker facility code. A zero length string in the entry for the …	OctetStringr/w Constraints: range: 0-108	.1.3.6.1.2.1.10.5.9.1.30