PANDUIT-MIB Table View

Aggregate Object with number of entries equal to pdug5NumberPDU .

pdug5IdentEntry row .1.3.6.1.4.1.19536.10.1.1.2.1

The Identity table entry containing the name, model, manufacturer,
firmware version, part number, etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5IdentIndex Index for the pdug5IdentEntry table.	Integer32	.1.3.6.1.4.1.19536.10.1.1.2.1.1
pdug5Name The string identify the device in daisy chain. Example PDU A.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.1.2.1.2
pdug5Model The Device Model.	OctetString	.1.3.6.1.4.1.19536.10.1.1.2.1.3
pdug5Manufacturer The Device Manufacturer Name.	OctetString	.1.3.6.1.4.1.19536.10.1.1.2.1.4
pdug5FirmwareVersion The firmware revision level of the device.	OctetString	.1.3.6.1.4.1.19536.10.1.1.2.1.5
pdug5FirmwareVersionTimeStamp Timestamp of when the PDU firmware was last updated	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.1.2.1.6
pdug5PartNumber The device part number. Example P36E09M.	OctetString	.1.3.6.1.4.1.19536.10.1.1.2.1.7
pdug5SerialNumber The device serial number, 10-digit.	OctetString	.1.3.6.1.4.1.19536.10.1.1.2.1.8
pdug5Status The overall status of the device. A value of OK(2) indicates the device is operating normally. A value of degraded(3) indicates the device is operating with warning indicators. A value of failed(4) indicates the devic…	Enumeration	.1.3.6.1.4.1.19536.10.1.1.2.1.9
pdug5Controllable This object indicates whether or not the device is controllable.	Enumeration	.1.3.6.1.4.1.19536.10.1.1.2.1.10
pdug5InputPhaseCount The number of input phase on this pdu 1 or 3.	Integer32	.1.3.6.1.4.1.19536.10.1.1.2.1.11
pdug5GroupCount The number of groups (breakers) on this pdu.	Integer32	.1.3.6.1.4.1.19536.10.1.1.2.1.12
pdug5OutletCount The number of outlets in this PDU.	Integer32	.1.3.6.1.4.1.19536.10.1.1.2.1.13
pdug5MACAddress The assigned MAC address for this PDU.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.1.2.1.14
pdug5IPv4Address The current IPv4 Address. A value of 0.0.0.0 indicates an error or an unset option.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.19536.10.1.1.2.1.15
pdug5IPv6Address The current IPv6 Address. A value of 0.0.0.0.0.0 indicates an error or an unset option.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.1.2.1.16
pdug5HWVersion The current Hardware Version. 1.0 - G5 (STM) No Powershare, 1.5 - G5 (STM) with Powershare, 2.0 - G6 Processor	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.1.2.1.17

Aggregate Object with number of entries equal to pdug5NumberPDU.

pdug5ConfigEntry row .1.3.6.1.4.1.19536.10.1.1.3.1

Read Configuration data from the PDU being queried.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5ConfigIndex The index of PDU configuration entry.	Integer32	.1.3.6.1.4.1.19536.10.1.1.3.1.1
pdug5ConfigSsh Setting this OID to off(0) will disable the SSH connection. Setting this OID to on(1) will enable the SSH connection. iNC reboot will be required for the settings to take effect.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.2
pdug5ConfigFtps Setting this OID to off(0) will disable the FTPS connection. Setting this OID to on(1) will enable the FTPS connection. iNC reboot will be required for the settings to take effect	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.3
pdug5ConfigHttp Setting this OID to off(0) will disable the HTTP connection. Setting this OID to on(1) will enable the HTTP connection.iNC reboot will be required for the settings to take effect	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.4
pdug5ConfigHttps Setting this OID to off(0) will disable the HTTPS connection. Setting this OID to on(1) will enable the HTTPS connection.iNC reboot will be required for the settings to take effect	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.5
pdug5ConfigIPv4IPv6Switch Setting this OID to IPv4(1) will enable the IPv4 configuration. Setting this OID to IPv6(2) will enable the IPv6 configuration. Setting this OID to IPv4&IPv6(3) will enable both IPv4 and IPv6 configuration.iNC reboot wi…	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.6
pdug5ConfigRedfishAPI Setting this OID to off(0) will disable the Redfish API. Setting this OID to on(1) will enable the Redfish API.iNC reboot will be required for the settings to take effect	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.7
pdug5ConfigOledDispalyOrientation Indicates the intended physical orientation of OLED display. displayNormal(1) indicates normal orientation. displayReverse(2) indicates upside down orientation.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.8
pdug5ConfigEnergyReset Setting this OID to reset(2) will cause the device energy meter value to be reset to zero. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value. Models that do not sup…	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.9
pdug5ConfigNetworkManagementCardReset Getting this OID will return noOperation(0). Getting this OID to reset(1) will reset iNC.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.10
pdug5ConfigDaisyChainStatus Setting this OID will change daisychain mode. 0:QNA,1:DNA.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.11
pdug5ConfigTelnet Setting this OID to off(0) will disable the Telnet connection. Setting this OID to on(1) will enable the Telnet connection. iNC reboot will be required for the settings to take effect.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.3.1.12

Aggregate Object with number of entries equal to number of PDUs and Power share

pdug5PowershareEntry row .1.3.6.1.4.1.19536.10.1.1.4.1

The Power share entry containing the available, input, output etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5PowershareIndex The index of the PDU Power share table entry	Integer32	.1.3.6.1.4.1.19536.10.1.1.4.1.1
pdug5PowershareFunctionStatus Power share function status on PDU.	Enumeration	.1.3.6.1.4.1.19536.10.1.1.4.1.2
pdug5PowershareFunctionUpstreamStatus Power share function status on upstream PDU	Enumeration	.1.3.6.1.4.1.19536.10.1.1.4.1.3
pdug5PowershareOutput Power share output status.	Enumeration	.1.3.6.1.4.1.19536.10.1.1.4.1.4
pdug5PowershareInput Power share input status.	Enumeration	.1.3.6.1.4.1.19536.10.1.1.4.1.5
pdug5PowershareOptMode Power share operation status of PDU. 0 meaning pdu is using powershare to power the NMC, 1 meaning pdu is using mains power to power the NMC	Enumeration	.1.3.6.1.4.1.19536.10.1.1.4.1.6
pdug5PowershareFunc Enable/Disable Powershare function of PDU. Set 1 to enable powershare. Set 0 to disable powershare	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.1.4.1.7

Aggregate Object with number of entries equal to pdug5NumberPDU .

pdug5InputEntry row .1.3.6.1.4.1.19536.10.1.2.1.1

The ident table entry containing the VA, Watts, WH, etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5InputType Type of input - single phase, split phase, three phase delta, or three phase wye.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.1.1.1
pdug5InputFrequency The measured input frequency from the PDU meters in tenths of Hz.	Integer32	.1.3.6.1.4.1.19536.10.1.2.1.1.2
pdug5InputFrequencyStatus Status of the measured input frequency relative to the nominal frequency and the admitted tolerance.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.1.1.3
pdug5InputPowerVA A total input VA of all phases. Units are VA. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.4
pdug5InputPowerWatts A total input Watts of all phases. Units are Watts. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.5
pdug5InputTotalEnergy A total input Watt-Hour value for all phases. Units are KWh. This value is accumulated since PDU in service. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.6
pdug5InputPowerWattHourTimer A Timestamp of when the Total Input WH was last reset.	OctetString	.1.3.6.1.4.1.19536.10.1.2.1.1.7
pdug5InputResettableEnergy A total input Watt-Hour value for all phases. Units are Wh. This value can be reset to 0 using GUI. In that case, the pdug5InputPowerWattHourTimer will be reset as well A negative value indicates that this object is no…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.8
pdug5InputPowerFactor An input PF value. Units are in hundredths, for example a power factor of 0.95 would be returned as 95, and 0.92 would be returned as 92. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.9
pdug5InputPowerVAR An input VAR value. Units are VAR. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.10
pdug5InputTotalCurrent All phases total current value. Units are 0.01 amps. For 3 phase, mathematically add totally 3 phase current together.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.1.1.11

Aggregate Object with number of entries equal to number of PDUs (pdug5NumberPDU) and
number of input phase (pdug5InputPhaseCount).

pdug5InputPhaseEntry row .1.3.6.1.4.1.19536.10.1.2.2.1

The input table entry containing the voltage, current, frequency, power for each phase.
Entries are given with number of pdu and number of input phase 1, 2, or 3.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5InputPhaseIndex Index for the pdug5InputEntry table.	Integer32	.1.3.6.1.4.1.19536.10.1.2.2.1.1
pdug5InputPhaseVoltageMeasType Value indicates what input voltage is being measured in this table row - single phase voltage, phase 1 to neutral, phase 2 to neutral, phase 3 to neutral, phase 1 to phase 2, phase 2 to phase 3, or phase 3 to phase 1.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.2.1.2
pdug5InputPhaseVoltage An input voltage measurement value. Values is in 0.1 V.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.3
pdug5InputPhaseVoltageThStatus Status of the measured input voltage relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.2.1.4
pdug5InputPhaseVoltageThLowerWarning Lower warning threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.5
pdug5InputPhaseVoltageThLowerCritical Lower critical threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.6
pdug5InputPhaseVoltageThUpperWarning Upper warning threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.7
pdug5InputPhaseVoltageThUpperCritical Upper critical threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.8
pdug5InputPhaseCurrentMeasType Which input wire is being measured in this table row - single phase, neutral, phase 1, phase 2, or phase 3.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.2.1.9
pdug5InputPhaseCurrentRating Rated current capacity of the input. A negative value indicates that the hardware current capacity is unknown. Units are 0.01 amps.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.10
pdug5InputPhaseCurrent An input current measurement value. Units are 0.01 amps.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.11
pdug5InputPhaseCurrentThStatus Status of the measured input current relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.2.1.12
pdug5InputPhaseCurrentThLowerWarning Lower warning threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.13
pdug5InputPhaseCurrentThLowerCritical Lower critical threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.14
pdug5InputPhaseCurrentThUpperWarning Upper warning threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.15
pdug5InputPhaseCurrentThUpperCritical Upper critical threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.16
pdug5InputPhaseCurrentPercentLoad Current percent load, based on the rated current capacity. Units are percentage, for example 80% will be returned as 80. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.17
pdug5InputPhasePowerMeasType Which input wire is being measured in this table row - single phase, neutral, phase 1, phase 2, or phase 3.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.2.1.18
pdug5InputPhasePowerVA An input VA value. Units are VA. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.19
pdug5InputPhasePowerWatts An input Watts value. Units are Watts. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.20
pdug5InputPhasePowerWattHour A Watt-Hour value for each Input phase. Units are WH. This value can be reset to 0 using GUI. In that case, the pdug5InputPhasePowerWattHourTimer will be reset as well A negative value indicates that this object is not…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.21
pdug5InputPhasePowerWattHourTimer Timestamp of when input Watt-hours (inputWh) was last reset.	OctetString	.1.3.6.1.4.1.19536.10.1.2.2.1.22
pdug5InputPhasePowerFactor An input PF value. Units are in hundredths, for example a power factor of 0.95 would be returned as 95, and 0.92 would be returned as 92. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.23
pdug5InputPhasePowerVAR An input VAR value. Units are VAR. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.24
pdug5InputPhaseVoltageThResetThld The Reset threshold is the number of volts the reading needs to fall below the threshold setting for the condition to be cleared. Units are 0.1 volts.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.25
pdug5InputPhaseVoltageThChangeDelay The number of consecutive sample that the condition is present before an alarm is raised.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.26
pdug5InputPhaseVoltageThCtrl Input phase voltage alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.27
pdug5InputPhaseCurrentThResetThld The Reset threshold is the number of amps the reading needs to fall below the threshold setting for the condition to be cleared. Units are 0.01 amps.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.28
pdug5InputPhaseCurrentThChangeDelay The number of consecutive sample that the condition is present before an alarm is raised.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.29
pdug5InputPhaseCurrentThCtrl Input phase current alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.30
pdug5InputPowerThresholdThLowerWarning Lower warning Power threshold. Units are in Watts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.31
pdug5InputPowerThresholdThLowerCritical Lower critical Power threshold. Units are in Watts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.32
pdug5InputPowerThresholdThUpperWarning Upper warning Power threshold. Units are in Watts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.33
pdug5InputPowerThresholdThUpperCritical Upper critical Power threshold. Units are in Watts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.34
pdug5InputPowerThresholdThResetThld The Reset threshold is the number of watts the reading needs to fall below the threshold setting for the condition to be cleared. Units are watts.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.35
pdug5InputPowerThresholdThChangeDelay The number of consecutive sample that the condition is present before an alarm is raised.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.36
pdug5InputPowerThresholdThCtrl Power alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 - enable, 1 -…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.37
pdug5InputEnergyThresholdThUpperWarning Upper warning Energy threshold. Units are in Watts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.38
pdug5InputEnergyThresholdThUpperCritical Upper critical Energy threshold. Units are in Watts. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.39
pdug5InputEnergyThresholdThResetThld The Reset threshold is the number of watts the reading needs to fall below the threshold setting for the condition to be cleared. Units are watts.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.40
pdug5InputEnergyThresholdThChangeDelay The number of consecutive sample that the condition is present before an alarm is raised.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.2.1.41
pdug5InputEnergyThresholdThCtrl Energy alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 - enable, 1 …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.2.1.42
pdug5InputPhasePowerThStatus Status of the measured input current relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.2.1.43

Aggregate Object with number of entries equal to number of PDUs (pdug5NumberPDU) and
number of RCM modules per PDU.

pdug5InputRcmEntry row .1.3.6.1.4.1.19536.10.1.2.3.1

The ident table entry containing the RCM Module status, RCM current, RCM module threshold settings, etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5InputRcmEnabled RCM configuration value off(0) if the PDU doesn't have RCM, on(1) if the PDU has RCM.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.3.1.1
pdug5InputRcmModStatus RCM module status ok(2) if the PDU can communicate with the RCM module, failed(4) if the PDU cannot communicate with the RCM module, degraded(3) if the PDU can communicate with the RCM module and the last self-test fail…	Enumeration	.1.3.6.1.4.1.19536.10.1.2.3.1.2
pdug5InputRcmThUpperWarning RCM Current Upper warning threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.3.1.3
pdug5InputRcmThUpperCritical RCM Current Upper critical threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.3.1.4
pdug5InputRcmThResetThld The Reset threshold is the number of amps the reading needs to fall below the threshold setting for the condition to be cleared. Units are 0.01 amps.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.3.1.5
pdug5InputRcmThChangeDelay The number of consecutive sample that the condition is present before an alarm is raised.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.3.1.6
pdug5InputRcmThCtrl Rcm current alarm threshold control: 0 - Enable UC and UW 1 - Disable UC and Enable UW 2 - Enable UC and Disable UW 3 - Disable UC and UW 4 and above - Bad input	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.3.1.7
pdug5InputRcmThStatus Status of the measured Rcm current relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.2.3.1.8
pdug5InputRcmCurrent Rcm module current reading. Units are milliAmps.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.2.3.1.9

Aggregate Object with number of entries equal to number of PDUs (pdug5NumberPDU) and
number of Rcm modules per PDU.

pdug5InputRcmSelfTestEntry row .1.3.6.1.4.1.19536.10.1.2.4.1

The ident table entry containing the Rcm Module Self Test Enable, Schedule, LastRunTime,LastRunStatus etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5InputRcmSelfTestEnable Rcm Self Test configuration value Disable(0) if the self test is disabled on the PDU, Enable(1) if self test is enabled on the PDU .	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.2.4.1.1
pdug5InputRcmSelfTestFreq Rcm module self test run frequency , the time for the test is set from Pdug5RcmSelfTestNextRunTime, the self test will be repeated based on the setting as Daily(1),Weekly(2),First Day Of Month(3),Yearly(4)	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.2.4.1.2
pdug5InputRcmSelfTestHour Rcm module self test schedule hour setting (0 to 23 hour),-1 means feature not available	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.4.1.3
pdug5InputRcmSelfTestMinute Rcm module self test schedule minute setting (0 to 59 minute),-1 means feature not available	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.4.1.4
pdug5InputRcmSelfTestDay Rcm module self test schedule day setting - Can be 0 to 6 when pduInputRcmSelfTestFreq is weekly(2), - Can be 1 to 31 when pduInputRcmSelfTestFreq is monthly(3) or yearly(4), - (-1) means feature not available	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.4.1.5
pdug5InputRcmSelfTestMonth Rcm module self test schedule month setting,-1 means feature not available	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.2.4.1.6
pdug5InputRcmSelfTestNextRunTime next run date and Time for self test.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.2.4.1.7
pdug5InputRcmSelfTestLastRunTime Date and Time when the self test run previously	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.2.4.1.8
pdug5InputRcmSelfTestLastRunStatus Status of the lastest self test run	Enumeration	.1.3.6.1.4.1.19536.10.1.2.4.1.9
pdug5InputRcmSelfTest Rcm module on demand self test, 1 to start the on demand self test	Integer32r/w	.1.3.6.1.4.1.19536.10.1.2.4.1.10

Aggregate Object with number of entries equal to number of PDUs
and number of breakers (pdug5GroupCount).

pdug5GroupEntry row .1.3.6.1.4.1.19536.10.1.3.1.1

The input table entry containing the name, voltages, currents, power, etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5GroupIndex Index for the pdug5GroupEntry table.	Integer32	.1.3.6.1.4.1.19536.10.1.3.1.1.1
pdug5GroupName A descriptive name for the group.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.3.1.1.2
pdug5GroupType The type of the group. (5) has no breaker	Enumeration	.1.3.6.1.4.1.19536.10.1.3.1.1.3
pdug5GroupVoltageMeasType Value indicates what input voltage is being measured in this table row - single phase voltage, phase 1 to neutral, phase 2 to neutral, phase 3 to neutral, phase 1 to phase 2, phase 2 to phase 3, or phase 3 to phase 1.	Enumeration	.1.3.6.1.4.1.19536.10.1.3.1.1.4
pdug5GroupVoltage Units are 0.1 volts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.5
pdug5GroupVoltageThStatus Status of the measured group voltage relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.3.1.1.6
pdug5GroupVoltageThLowerWarning Lower warning threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32	.1.3.6.1.4.1.19536.10.1.3.1.1.7
pdug5GroupVoltageThLowerCritical Lower critical threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32	.1.3.6.1.4.1.19536.10.1.3.1.1.8
pdug5GroupVoltageThUpperWarning Upper warning threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32	.1.3.6.1.4.1.19536.10.1.3.1.1.9
pdug5GroupVoltageThUpperCritical Upper critical threshold. Units are 0.1 volts. A negative value indicates that this object is not available.	Integer32	.1.3.6.1.4.1.19536.10.1.3.1.1.10
pdug5groupCurrentRating Rated current capacity of the group. Units are 0.01 amps. A negative value indicates that the hardware current capacity is unknown (it will always be unknown for custom groups).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.11
pdug5GroupCurrent A group current measurement value. Units are 0.01 amps.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.12
pdug5GroupCurrentThStatus Status of the measured group current relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.3.1.1.13
pdug5GroupCurrentThLowerWarning Lower warning threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.3.1.1.14
pdug5GroupCurrentThLowerCritical Lower critical threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.3.1.1.15
pdug5GroupCurrentThUpperWarning Upper warning threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.3.1.1.16
pdug5GroupCurrentThUpperCritical Upper critical threshold. Units are 0.01 amps. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.3.1.1.17
pdug5GroupCurrentPercentLoad Current percent load, based on the rated current capacity. Units are percentage, for example 80% will be returned as 80. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.18
pdug5GroupPowerVA A group VA value. Units are VA. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.19
pdug5GroupPowerWatts A group power value. Units are Watts. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.20
pdug5GroupPowerWattHour A Watt-Hour value for each section. Units are WH. This value can be reset to 0 using GUI. In that case, the pdug5GroupPowerWattHourTimer will be reset as well. A negative value indicates that this object is not availab…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.21
pdug5GroupPowerWattHourTimer Timestamp of when group Watt-hours (groupWh) was last reset.	OctetString	.1.3.6.1.4.1.19536.10.1.3.1.1.22
pdug5GroupPowerFactor A group PF value. Units are in hundredths, for example a power factor of 0.95 would be returned as 95, and 0.92 would be returned as 92. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.23
pdug5GroupPowerVAR A group VAR value. Units are VAR. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.24
pdug5GroupOutletCount The number of outlets in each group (breaker).	Integer32	.1.3.6.1.4.1.19536.10.1.3.1.1.25
pdug5GroupBreakerStatus Only applicable to groups with breaker. Indicates whether a breaker is turned off or on.	Enumeration	.1.3.6.1.4.1.19536.10.1.3.1.1.26
pdug5GroupVoltageThCtrl Circuit Breaker voltage alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.27
pdug5GroupCurrentThCtrl Circuit Breaker current alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.3.1.1.28

A list of environment probe (1 per PDU) for temperature, humidity, and contacts.
The number of entries is given by number of PDUs in daisy chain.

pdug5EnvProbeEntry row .1.3.6.1.4.1.19536.10.1.4.1.1

Aggregate entries equal to number of PDUs.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5TemperatureScale Scale used to return temperature objects.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.1.1.1
pdug5TemperatureCount The number of temperature measurements.The MAX is 6 (1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.2
pdug5HumidityCount The number of humidity measurements.The MAX is 6(1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.3
pdug5DoorCount The number of door sensors.The MAX is 6(1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.4
pdug5DryCount The number of dry sensors.The MAX is 2(1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.5
pdug5SpotCount The number of spot sensors.The MAX is 2(1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.6
pdug5RopeCount The number of rope sensors.The MAX is 2(1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.7
pdug5HidCount The number of hid sensors. The MAX is 2(1 per probe).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.1.1.10

A list of temperature probe measurements.  The number of entries are
given by number of pdu and pdug5TemperatureCount.

pdug5TemperatureEntry row .1.3.6.1.4.1.19536.10.1.4.2.1

An entry for a temperature measurement.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5TemperatureIndex A unique value for each temperature probe measurement. Its value ranges from 1 to temperatureCount.	Integer32	.1.3.6.1.4.1.19536.10.1.4.2.1.1
pdug5TemperatureName A descriptive name for the temperature probe.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.4.2.1.2
pdug5TemperatureProbeStatus Indicates whether a probe is connected or not.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.2.1.3
pdug5TemperatureValue Units are degree(either Fahrenheit or Celsius).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.2.1.4
pdug5TemperatureThStatus Status of the measured temperature relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.2.1.5
pdug5TemperatureThLowerWarning Lower warning threshold. Units are degrees. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.2.1.6
pdug5TemperatureThLowerCritical Lower critical threshold. Units are degrees. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.2.1.7
pdug5TemperatureThUpperWarning Upper warning threshold. Units are degrees. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.2.1.8
pdug5TemperatureThUpperCritical Upper critical threshold. Units are degrees. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.2.1.9
pdug5TemperatureThCtrl Temperature alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 - enabl…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.2.1.10

A list of humidity probe measurements.  The number of entries are
given by number of pdu and pdug5HumidityCount.

pdug5HumidityEntry row .1.3.6.1.4.1.19536.10.1.4.3.1

An entry for a humidity measurement.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5HumidityIndex A unique value for each humidity probe measurement. Its value ranges from 1 to pdug5HumidityCount per PDU.	Integer32	.1.3.6.1.4.1.19536.10.1.4.3.1.1
pdug5HumidityName A descriptive name for the humidity probe.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.4.3.1.2
pdug5HumidityProbeStatus Indicates whether a probe is connected or not.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.3.1.3
pdug5HumidityValue Units are %RH.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.3.1.4
pdug5HumidityThStatus Status of the measured humidity relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.3.1.5
pdug5HumidityThLowerWarning Lower warning threshold. Units are %RH. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.3.1.6
pdug5HumidityThLowerCritical Lower critical threshold. Units are %RH. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.3.1.7
pdug5HumidityThUpperWarning Upper warning threshold. Units are %RH. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.3.1.8
pdug5HumidityThUpperCritical Upper critical threshold. Units are %RH. A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.4.3.1.9
pdug5HumidityThCtrl Humidity alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 - enable, …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.3.1.10

A list of door sensors.  The number of entries are
given by number of PDU and pdug5DoorCount.

pdug5DoorEntry row .1.3.6.1.4.1.19536.10.1.4.4.1

An entry for a door sensor

Indexes

No indexes recorded

Column	Syntax	OID
pdug5DoorIndex A unique value for each door sensor. Its value ranges from 1 to doorCount.	Integer32	.1.3.6.1.4.1.19536.10.1.4.4.1.1
pdug5DoorName A descriptive name for the door sensor.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.4.4.1.2
pdug5DoorProbeStatus Indicates whether a probe is connected or not. Will not be returned if the door sensor is internal to the ePDU, in that case only doorState should be read.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.4.1.3
pdug5DoorState The state of the door sensor.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.4.1.4

A list of dry sensors.  The number of entries are
given by number of pdu and pdug5DryCount.

pdug5DryEntry row .1.3.6.1.4.1.19536.10.1.4.5.1

An entry for a contact sensor

Indexes

No indexes recorded

Column	Syntax	OID
pdug5DryIndex A unique value for each dry sensor. Its value ranges from 1 to dryCount.	Integer32	.1.3.6.1.4.1.19536.10.1.4.5.1.1
pdug5DryName A descriptive name for the dry sensor.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.4.5.1.2
pdug5DryProbeStatus Indicates whether a probe is connected or not.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.5.1.3
pdug5DryState The state of the dry sensor.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.5.1.4

A list of contact sensors.  The number of entries are
given by number of pdu and pdug5SpotCount.

pdug5SpotEntry row .1.3.6.1.4.1.19536.10.1.4.6.1

An entry for a contact sensor

Indexes

No indexes recorded

Column	Syntax	OID
pdug5SpotIndex A unique value for each spot sensor. Its value ranges from 1 to spotCount.	Integer32	.1.3.6.1.4.1.19536.10.1.4.6.1.1
pdug5SpotName A descriptive name for the spot sensor.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.4.6.1.2
pdug5SpotProbeStatus Indicates whether a probe is connected or not.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.6.1.3
pdug5SpotState The state of the spot sensor.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.6.1.4

A list of rope sensors.  The number of entries are
given by number of pdu and pdug5RopeCount.

pdug5RopeEntry row .1.3.6.1.4.1.19536.10.1.4.7.1

An entry for a contact sensor

Indexes

No indexes recorded

Column	Syntax	OID
pdug5RopeIndex A unique value for each rope sensor. Its value ranges from 1 to ropeCount.	Integer32	.1.3.6.1.4.1.19536.10.1.4.7.1.1
pdug5RopeName A descriptive name for the rope sensor.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.4.7.1.2
pdug5RopeProbeStatus Indicates whether a probe is connected or not.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.7.1.3
pdug5RopeState The state of the rope sensor.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.7.1.4

A list of contact sensors.  The number of entries are
given by number of pdu and pdug5HidCount.

pdug5EnvHidEntry row .1.3.6.1.4.1.19536.10.1.4.10.1.1

An entry for a contact sensor

Indexes

No indexes recorded

Column	Syntax	OID
pdug5HIDIndex The index of the PDU HID table entry	Integer32	.1.3.6.1.4.1.19536.10.1.4.10.1.1.1
pdug5HidAisle Aisle of HID handle.	Enumeration	.1.3.6.1.4.1.19536.10.1.4.10.1.1.2
pdug5HidHandleOperation HID handle control operations	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.1.1.3
pduHIDVer The firmware revision level of the HID	OctetString	.1.3.6.1.4.1.19536.10.1.4.10.1.1.4
pdug5MechanicalLock HID Mechanical operations	Enumeration	.1.3.6.1.4.1.19536.10.1.4.10.1.1.5
pduHIDSerial The Serial Number of the HID	OctetString	.1.3.6.1.4.1.19536.10.1.4.10.1.1.6
pduHIDHwVer The hardware revision level of the HID	OctetString	.1.3.6.1.4.1.19536.10.1.4.10.1.1.7
pdug5HIDAutoLockTime HID Electronic Latch Autolock Time in seconds, Value ranges (0-999)	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.10.1.1.8
pdug5HIDDoorOpenTime HID Door Open Time in seconds, Value ranges (0-999)	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.10.1.1.9
pdug5HIDMaxDoorOpenTime HID Max Door Open Time in seconds, Value ranges (0-32400), critical alarm will be raised if door is left open past this time	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.10.1.1.10
pdug5HIDUserPinLength Rack Access User minimum PIN Length, value ranges(0-16)	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.10.1.1.11
pdug5HIDUserPinMode Rack Access User PIN mode setting	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.1.1.12
pdug5HIDAisleControl Rack Access Aisle Control setting, when set to standalone each aisle will controlled separately, when set to combined opposite aisle can be controlled with authenticated control action on either aisle	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.1.1.13
pdug5HIDBeaconFuncControl Beacon Function Control	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.1.1.14
pdug5HidBeaconColorControl Beacon Color Control	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.1.1.15

A list of smartcard.  The number of entries are
given by number of pdu and pdug5HidCount.

pdug5EnvHidControlEntry row .1.3.6.1.4.1.19536.10.1.4.10.2.1

The smart card table entry containing the username, cardid, cardaisle etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5HidControlIndex The index of the PDU smartcard table entry	Integer32	.1.3.6.1.4.1.19536.10.1.4.10.2.1.1
pdug5HidControlUserName User name of smartcard. Use #delete# to delete the HID user	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.4.10.2.1.2
pdug5HidControlCardID HID smartcard ID.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.4.10.2.1.3
pdug5HidControlTimestamp Indicates the date and time of accessing	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.4.10.2.1.4
pdug5HidControlCardAisle Aisle of authorized card	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.2.1.5
pdug5HidControlStartTime Indicates the start date and time Rack access user is given access	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.4.10.2.1.6
pdug5HidControlExpireTime Indicates the date and time when the access of user card will expire, To set expire time first set user as temporary user	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.4.10.2.1.7
pdug5HidControlTempUser Indicates if the card user has temporary access	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.4.10.2.1.8
pdug5HidControlPin Rack access control entry keypad PIN	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.4.10.2.1.9
pdug5HidControlCardIdStr Smartrack Access Card ID String	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.4.10.2.1.10

Aggregate Object with number of entries equal to Number of PDU (pdug5IdentIndex)
and Number of outlet per PDU (pdug5OutletIndex).

pdug5OutletEntry row .1.3.6.1.4.1.19536.10.1.5.1.1

The Outlet table entry containing the type, voltage, current etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5OutletIndex Index for each outlet, value from 1 to the number of outlets per PDU.	Integer32	.1.3.6.1.4.1.19536.10.1.5.1.1.1
pdug5OutletName A descriptive name for the outlet.	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.5.1.1.2
pdug5OutletType Type of this outlet - C13, C19, 5-20R, iecC13/C15 COMBO, iecC13/C15/C19 COMBO...	Enumeration	.1.3.6.1.4.1.19536.10.1.5.1.1.3
pdug5OutletCurrentRating Rated current capacity of this outlet. Units are 0.01 amps. A negative value indicates that the hardware current capacity is unknown.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.4
pdug5OutletCurrent A outlet current measurement value. Units are 0.01 amps.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.5
pdug5OutletActivePowerThStatus Status of the measured outlet active power relative to the configured thresholds.	Enumeration	.1.3.6.1.4.1.19536.10.1.5.1.1.6
pdug5OutletActivePowerThLowerWarning Lower warning threshold. Units are Watts(W). A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.1.1.7
pdug5OutletActivePowerThLowerCritical Lower critical threshold. Units are Watts(W). A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.1.1.8
pdug5OutletActivePowerThUpperWarning Upper warning threshold. Units are Watts(W). A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.1.1.9
pdug5OutletActivePowerThUpperCritical Upper critical threshold. Units are Watts(W). A negative value indicates that this object is not available.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.1.1.10
pdug5OutletCurrentPercentLoad Current percent load, based on the rated current capacity. Units are percentage, for example 80% will be returned as 80. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.11
pdug5OutletVA A outlet VA value. Units are VA. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.12
pdug5OutletWatts A outlet Watts value. Units are Watts. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.13
pdug5OutletWh A Watt-Hour value for each outlet. Units are WH. This object is writable so that it can be reset to 0. When it is written to, the pdug5OutletWhTimer will be reset updated as well A negative value indicates that this o…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.14
pdug5OutletWhTimer Timestamp (date and time) of outlet Watt-hours was last reset.	OctetString	.1.3.6.1.4.1.19536.10.1.5.1.1.15
pdug5OutletPowerFactor An outlet PF value. Units are in hundredths, for example a power factor of 0.95 would be returned as 95, and 0.92 would be returned as 92. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.16
pdug5OutletVAR An outlet VAR value. Units are VAR. A negative value indicates that this object is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.17
pdug5OutletBranch The branch number outlet located.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.18
pdug5OutletActivePowerThResetThld The Reset threshold is the number of watss the reading needs to fall below the threshold setting for the condition to be cleared. Units are watts.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.1.1.19
pdug5OutletActivePowerThChangeDelay The number of consecutive sample that the condition is present before an alarm is raised.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.1.1.20
pdug5OutletActivePowerThCtrl Outlet Active Power alarm threshold control: bit 0: up critical alarm control bit, 0 - enable, 1 - disable bit 1: up warning alarm control bit, 0 - enable, 1 - disable bit 2: low warning alarm control bit, 0 …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.1.1.21

Aggregate Object with number of entries equal to Number of PDU (pdug5IdentIndex)
and Number of outlets per PDU (pdug5OutletIndex).

pdug5OutletControlEntry row .1.3.6.1.4.1.19536.10.1.5.2.1

The Outlet table entry containing the type, voltage, current etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5OutletControlStatus current state of a control outlet.	Enumeration	.1.3.6.1.4.1.19536.10.1.5.2.1.1
pdug5OutletControlOffCmd When write, once issued, the outlet will turn Off immediately. 0-n: Time in seconds until the outlet command is issued -1: Cancel a pending outlet Off command When read, returns -1 if no command is pending, or the curre…	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.2.1.2
pdug5OutletControlOnCmd When write, once issued, the outlet will turn On immediately. 0-n: Time in seconds until the outlet command is issued -1: Cancel a pending outlet On command When read, returns -1 if no command is pending, or the current…	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.2.1.3
pdug5OutletControlRebootCmd When write, for outlets that are On prior to this Reboot command, they will switch Off immediately when the command is issued, remain Off for outletControlRebootOffTime seconds, and then turn back On. For outlets that a…	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.2.1.4
pdug5OutletControlPowerOnState Determines the outlet state when power is applied to the unit. 1 : not restart at device startup 2 : should sequence back ON in line with outletControlSequenceTime 3 : should take the state the outlet had when power was…	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.5.2.1.5
pdug5OutletControlSequenceDelay Time delay in seconds from when a Global Sequence On command is issued to when the command is executed on this outlet. This delay is also used as a power-on delay.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.2.1.6
pdug5OutletControlRebootOffTime Time delay in seconds that the outlet should remain in the Off state when executing a Reboot command.	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.2.1.7
pdug5OutletControlSwitchable Determines the outlet capability to be controlled On/Off from the communication channels. 1 : control On/Off enabled 2 : control On/Off disabled.	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.5.2.1.8
pdug5OutletControlShutoffDelay Time delay in seconds that could be taken in account before shutting of the outlet. An application which need to shutoff properly an outlet will read this parameter first then write it to the command pdug5OutletControlO…	Integer32r/w	.1.3.6.1.4.1.19536.10.1.5.2.1.9
pdug5OutletControlCommand Getting this variable will return the outlet state. If the outlet is on, the immediateOn (2) value will be returned. If the outlet is off, the immediateOff (1) value will be returned. If the state of the outlet cannot b…	Enumerationr/w	.1.3.6.1.4.1.19536.10.1.5.2.1.10

Aggregate Object with Number of outlets per Group (pdug5OutletGroupsIndex).

pdug5OutletGroupEntry row .1.3.6.1.4.1.19536.10.1.5.3.1

The Outlet Group table entry containing the count, name, member etc.

Indexes

No indexes recorded

Column	Syntax	OID
pdug5OutletGroupCount The numeric Switched Outlet Groups Count	Integer32	.1.3.6.1.4.1.19536.10.1.5.3.1.1
pdug5OutletGroupName The user-defined switched outlet Groups Name string	OctetStringr/w	.1.3.6.1.4.1.19536.10.1.5.3.1.2
pdug5OutletGroupMemberID The user-defined switched outlet Group Members string	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.5.3.1.3
pdug5OutletGroupControl Getting this variable will return the group state. If the group is on, the immediateOn (2) value will be returned. If the group is off, the immediateOff (1) value will be returned. If the state of the group cannot be de…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.19536.10.1.5.3.1.4
pdug5OutletGroupActivePower The Sum of Active power of all Grouped Outlet.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.3.1.5
pdug5OutletGroupApparentPower The Sum of Apparent power of all Grouped Outlet.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.19536.10.1.5.3.1.6