OMNITRON-POE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
1
Rows
1
Columns
16

ostPoePortCfgTable

table
.1.3.6.1.4.1.7342.15.2 · 1 row entry · 16 columns
Open in standard view
Uses the omnitron variant from /opt/observium/mibs/omnitron.
Command help
Walk ostPoePortCfgTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'OMNITRON-POE-MIB' -M '/opt/observium/mibs/omnitron:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'OMNITRON-POE-MIB::ostPoePortCfgTable' 
This table supports the port PoE configurations.
ostPoePortCfgEntry row .1.3.6.1.4.1.7342.15.2.1
This is a PoE port configuration table entry.
Indexes
Column Syntax OID
ostPoePortCfgIndex
An index that is used to identify a specific PoE port number.
OMNITRON-TC-MIBOstPortSingleIndex
Type Constraints:
range: 10101..999999
 .1.3.6.1.4.1.7342.15.2.1.1
ostPoePortPseEnable
This object is the PoE PSE port enable.

pseDisabled(1) PSE power source is disabled
pseEnabled(2) PSE power source is enabled
Enumerationr/w
Enumerated Values:
1pseDisabled
2pseEnabled
 .1.3.6.1.4.1.7342.15.2.1.2
ostPoePortPseMaxMode
The object is the PoE maximum mode enable. This is the same control as
the physical DIP switch.

pseMaxNotAvail PSE maximum mode function not available
pseMaxAuto(1) PSE maximum mode a…
Enumerationr/w
Enumerated Values:
0pseMaxNotAvail
1pseMaxAuto
2pseMaxForce
 .1.3.6.1.4.1.7342.15.2.1.3
ostPoePortPdMode
This object is the PoE PD classification mode.

pdModeNotDetected(1) PD is not detected
pdModeNotClassified(2) PD is not classified
pdModeFailure(3) PD classification failure
pdModeClass0(4) …
Enumeration
Enumerated Values:
1pdModeNotDetected
2pdModeNotClassified
3pdModeFailure
4pdModeClass0
5pdModeClass1
6pdModeClass2
7pdModeClass3
8pdModeClass4
9pdMode60W
10pdMode75W
11pdMode90W
 .1.3.6.1.4.1.7342.15.2.1.4
ostPoePortPseVoltageSupplied
This object indicates the voltage output from the PSE port in volts.
OMNITRON-TC-MIBOstFloatValue
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.7342.15.2.1.5
ostPoePortPseCurrentSupplied
This object indicates the current output from the PSE port in mA
(milliamps).
OMNITRON-TC-MIBOstFloatValue
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.7342.15.2.1.6
ostPoePortPseStatus
This object is the PoE PSE port status.

notApplicable(1) PD device not connected or port disabled
pdNormal(2) PD device is being powered fully
pdOverCurrent(3) PD device is consu…
Enumerationr/w
Enumerated Values:
1notApplicable
2pdNormal
3pdOverCurrent
4pdBrownOut
5pdInsufficientPower
 .1.3.6.1.4.1.7342.15.2.1.7
ostPoePortHeartbeatEnable
This object is the PoE PSE heartbeat enable.

heartbeatDisabled(1) PSE PD heartbeat is disabled
heartbeatEnabled(2) PSE PD heartbeat is enabled
Enumerationr/w
Enumerated Values:
1heartbeatDisabled
2heartbeatEnabled
 .1.3.6.1.4.1.7342.15.2.1.8
ostPoePortHeartbeatIpAddress
This object is the PoE PD heartbeat IPv4 address to ping.

Setting this object also impacts the ostPoePortHeartbeatIpAddressString
returned value. If an IPv4 address is written to this object the
two objec…
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.7342.15.2.1.9
ostPoePortHeartbeatInterval
This object is the PoE PSE PD heartbeat transmission interval in seconds.
Unsigned32r/w
Constraints:
range: 1-300
 .1.3.6.1.4.1.7342.15.2.1.10
ostPoePortHeartbeatErrorDetection
This object is the PoE PSE PD heartbeat number of consecutively lost
heartbeat pings before an errored condition is declared. The number
of consecutive error counts is cleared when a valid heartbeat
response is received.
Unsigned32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.7342.15.2.1.11
ostPoePortHeartbeatErrorAction
This object is the PoE PSE heartbeat errored condition action.

errorLostIgnored(1) PD heartbeat errored condition is ignored
errorRestart(2) PD heartbeat errored condition results
…
Enumerationr/w
Enumerated Values:
1errorLostIgnored
2errorRestart
3errorShutdown
 .1.3.6.1.4.1.7342.15.2.1.12
ostPoePortHeartbeatNumberRestarts
This object is the PoE PSE PD number of restarts when an errored
hearbeat condition occurs. This object is only used when
ostPoePortHeartbeatErrorAction is configured as 'errorRestart'

A value of zero ind…
Unsigned32r/w
Constraints:
range: 0-16384
 .1.3.6.1.4.1.7342.15.2.1.13
ostPoEPortHeartbeatStatus
This object is the PoE PSE PD heartbeat status.

heartbeatDisabled(1) PSE PD heartbeat is disabled
heartbeatAvailable(2) PSE PD heartbeats are being received
heartbeatErrored(3) PSE PD heartbeat i…
Enumeration
Enumerated Values:
1heartbeatDisabled
2heartbeatAvailable
3heartbeatErrored
4heartbeatRestart
5heartbeatShutdown
 .1.3.6.1.4.1.7342.15.2.1.14
ostPoEPortHeartbeatDeferTime
This object is the PoE heartbeat PSE PD heartbeat transmission delay
interval in seconds after the port has been reenabled. The delay is
the amount of time after power has been applied before the heartbeat
function star…
Unsigned32r/w
Constraints:
range: 1-300
 .1.3.6.1.4.1.7342.15.2.1.15
ostPoePortHeartbeatIpAddressString
This object is the PoE PD heartbeat IPv4 or IPv6 address to ping.

Setting this object also impacts the ostPoePortHeartbeatIpAddress
returned value. If an IPv4 address is written to this object the
two obj…
OMNITRON-TC-MIBOstIpAddrr/w
Type Constraints:
range: 0..39
 .1.3.6.1.4.1.7342.15.2.1.16