NETLINK-SPECIFIC-MIB Table View

A table showing all nodes known to this node
along with status and neighbor information.

nsEntry row .1.3.6.1.4.1.173.6.1.3.1

Each entry of the node table is indexed by
node number.

Indexes

nsNodNum

Column	Syntax	OID
nsNodNummandatory The node number of the desired node. This is the index into the node table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.6.1.3.1.1
nsStatusmandatory The operational status of the node. The status is given as: 1 = Node is defined in the database; 9 = Node is operational;	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.6.1.3.1.2
nsNumNeighmandatory Current number of neighbor nodes to this node.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.6.1.3.1.3

The neighbor table lists the status of a nodes
neighbors.

nsNeighEntry row .1.3.6.1.4.1.173.6.1.4.1

The table entries are indexed by the node number and
the neighbors node number.

Indexes

nsNTNode nsNTNeigh

Column	Syntax	OID
nsNTNodemandatory The node number of the node whose neighbor's status is being sought.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.6.1.4.1.1
nsNTNeighmandatory The node number of the neighbor whose status is being sought.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.6.1.4.1.2
nsNTNeighStatmandatory The status of the neighbor node given as: 1 = previously, but not currently, connected; 2 = Currently connected;	Enumeration Enumerated Values: 1 notConnected 2 connected	.1.3.6.1.4.1.173.6.1.4.1.3

A table used to define the IP address of end-nodes
to receive alarms generated by this node. Up to 16 addresses
can be specified.

tpAdrEntry row .1.3.6.1.4.1.173.7.1.3.3.1

A Trap entry containing objects relating to SNMP traps.

Indexes

tpAdrIdx

Column	Syntax	OID
tpAdrIdxmandatory The index into the trap configuration table	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.1.3.3.1.1
tpAddressmandatory The IP Address of the end-station to send alarms	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.173.7.1.3.3.1.2
tpAdrFlagmandatory Defines the state of this entry as: 0 = Do not send traps to the Address; 1 = Send traps to the Address; 2 = This Address entry is deleted from the table;	Enumerationr/w Enumerated Values: 1 disableTraps 2 enableTraps 3 delete	.1.3.6.1.4.1.173.7.1.3.3.1.3
tpAdrSLevmandatory Lowest severity level traps that will be sent to this Address; 1 is the highest, 4 is the lowest.	Enumerationr/w Enumerated Values: 1 critical 2 major 3 minor 4 informational	.1.3.6.1.4.1.173.7.1.3.3.1.4

A Table to describe each RLP on the node

rlpEntry row .1.3.6.1.4.1.173.7.2.2.1

An RLP entry containing objects relating to RLPs.

Indexes

rlpIndex

Column	Syntax	OID
rlpIndexmandatory The RLP number on the node	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.2.2.1.1
rlpStatusmandatory The current state of this RLP	Enumeration Enumerated Values: 1 installed 2 configured 3 load-failed 4 loading 5 ipl-failed 6 ipl-in-progress 7 failed 8 operational 9 power-off 10 power-on	.1.3.6.1.4.1.173.7.2.2.1.2
rlpMemorySizemandatory The amount of memory installed on this RLP	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.2.2.1.3
rlpLIC1Typemandatory The Type of Line Interface card in the first position	Enumeration Enumerated Values: 1 none 2 rs232 3 rs422 4 v35 5 hs-rs232 6 x21 7 rs449 8 universal 10 t1 11 e1 13 voice	.1.3.6.1.4.1.173.7.2.2.1.4
rlpLIC2Typemandatory The Type of Line Interface card in the second position	Enumeration Enumerated Values: 1 none 2 rs232 3 rs422 4 v35 5 hs-rs232 6 x21 7 rs449 8 universal 10 t1 11 e1 13 voice	.1.3.6.1.4.1.173.7.2.2.1.5
rlpProtocolmandatory The protocols configured on this RLP. This is an OCTET STRING where each octet represents a protocol type. The size of this is the maximum number of protocols allowed on an RLP (rlpMaxProtos). The protocol types are de…	OctetStringr/w	.1.3.6.1.4.1.173.7.2.2.1.6
rlpGroupNumbermandatory The group to which this RLP belongs- always 1 if not FRX7000.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.173.7.2.2.1.7
rlpGroupResponsibilitymandatory The responsibility of this RLP within its group, always primary if not FRX7000.	Enumeration Enumerated Values: 1 primary 2 secondary	.1.3.6.1.4.1.173.7.2.2.1.8

This table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
          
Most of the objects in this read-write table have
corresponding read-only objects in the
portX25OperTable that return the current
operating value.
          
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started.

portPhyX25AdminEntry row .1.3.6.1.4.1.173.7.3.1.1.1

A list of configured values for an X25 port.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portPhyX25AdminConnectormandatory Physical port interface connector type.	Enumerationr/w Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1 11 e1	.1.3.6.1.4.1.173.7.3.1.1.1.1
portPhyX25AdminSpeedmandatory This object defines the speed of the X25 port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.1.1.1.2
portPhyX25AdminGenerateClockmandatory Specifies whether the port will generate the clock necessary to synchronize traffic over the link.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.1.1.3
portPhyX25AdminRcvClockFromDTEmandatory This object defines whether the receive clock will be used from the DTE.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.1.1.4
portPhyX25AdminDialOutmandatory This flag indicates whether the port is connected to a dial modem, and whethter connections will be initiated through dial-in or dial-out calls.	Enumerationr/w Enumerated Values: 1 none 2 dialIn 3 dialOut	.1.3.6.1.4.1.173.7.3.1.1.1.5
portPhyX25AdminInactivityTimermandatory This timer defines in minutes, the period of inactivity allowed between calls. Once the timer expires, the port is disabled untill the next call is placed, if a Dial out port, or the Disconnect Timer expires, if a Dial …	Integer32r/w Constraints: range: 1-30	.1.3.6.1.4.1.173.7.3.1.1.1.6
portPhyX25AdminDisconnectTimermandatory This timer defines, in seconds, the length of time a dial-in port will remain disabled after expiration of the InActivity Timer.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.1.1.1.7
portPhyX25AdminSetupTimermandatory This timer determines the length of time, in seconds, that a response must be received by the port, after entering the Linkup state. If a response is not received, the port enters a Failed state.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.1.1.1.8
portPhyX25AdminTrunkFlagmandatory This flag, when set, indicates the port is associated with a network trunk group. It will be disabled/enabled if the network trunk is not operational.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.1.1.9
portPhyX25AdminTrunkGroupmandatory This variable contains a string of 8 bytes, with each byte indicating 8 ports on an RLP that may be a part of a trunk group. Since a TurboFrad has only 1 RLP, only the first byte is valid if the node is an FRX4000. Each…	OctetStringr/w	.1.3.6.1.4.1.173.7.3.1.1.1.10
portPhyX25AdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portPhyX25AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', w…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.1.1.1.11

This table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
          
All of the objects in this table are read-only.
          
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started.

portPhyX25OperEntry row .1.3.6.1.4.1.173.7.3.1.2.1

A list of configured values for an X25 port.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portPhyX25OperConnectormandatory Physical port interface connector type.	Enumeration Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1 11 e1	.1.3.6.1.4.1.173.7.3.1.2.1.1
portPhyX25OperSpeedmandatory This object defines the speed of the X25 port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to …	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.1.2.1.2
portPhyX25OperGenerateClockmandatory Specifies whether the port will generate the clock necessary to synchronize traffic over the link.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.2.1.3
portPhyX25OperRcvClockFromDTEmandatory This object defines whether the receive clock will be used from the DTE.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.2.1.4
portPhyX25OperDialOutmandatory This flag indicates whether the port is connected to a dial modem, and whethter connections will be initiated through dial-in or dial-out calls.	Enumeration Enumerated Values: 1 none 2 dialIn 3 dialOut	.1.3.6.1.4.1.173.7.3.1.2.1.5
portPhyX25OperInactivityTimermandatory This timer defines in minutes, the period of inactivity allowed between calls. Once the timer expires, the port is disabled untill the next call is placed, if a Dial out port, or the Disconnect Timer expires, if a Dial …	Integer32 Constraints: range: 1-30	.1.3.6.1.4.1.173.7.3.1.2.1.6
portPhyX25OperDisconnectTimermandatory This timer defines, in seconds, the length of time a dial-in port will remain disabled after expiration of the InActivity Timer.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.1.2.1.7
portPhyX25OperSetupTimermandatory This timer determines the length of time, in seconds, that a response must be received by the port, after entering the Linkup state. If a response is not received, the port enters a Failed state.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.1.2.1.8
portPhyX25OperTrunkFlagmandatory This flag, when set, indicates the port is associated with a network trunk group. It will be disabled/enabled if the network trunk is not operational.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.2.1.9
portPhyX25OperTrunkGroupmandatory This variable contains a string of 8 bytes, with each byte indicating a port on this RLP that may be a part of a trunk group.	OctetString	.1.3.6.1.4.1.173.7.3.1.2.1.10

This table contains Netlink Enterprise specific
objects to manage an X25 Logical port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
          
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started.

portLogicalX25AdminEntry row .1.3.6.1.4.1.173.7.3.1.3.1

A list of configured values for an X25 logical port.

Indexes

nlIfRlp nlIfPhyPort nlIfPort

Column	Syntax	OID
portLogicalX25AdminFrDlcimandatory The DLCI number used to identify the entry in the table. The range is 16-991.	Integer32r/w Constraints: range: 16-991	.1.3.6.1.4.1.173.7.3.1.3.1.1
portLogicalX25AdminCxnPrioritymandatory This field sets the priority of the connection among others on the physical port. The range is 0 for lowest priority to 9 for the highest priority.	Integer32r/w Constraints: range: 0-9	.1.3.6.1.4.1.173.7.3.1.3.1.2
portLogicalX25AdminRfc1490mandatory This field indicates the encapsulation method used	Enumerationr/w Enumerated Values: 1 annexG 2 rfc1490	.1.3.6.1.4.1.173.7.3.1.3.1.3
portLogicalX25AdminBAGmandatory Assigns this DLCI to one of sixteen groups whose parameters regulate bandwidth usage. A 0 value indicates the DLCI does not use BAGs	Integer32r/w Constraints: range: 0-16	.1.3.6.1.4.1.173.7.3.1.3.1.4
portLogicalX25AdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portLogicalX25AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.1.3.1.5

This table contains Netlink Enterprise specific
objects to manage an X25 Logical port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
          
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started.

portLogicalX25OperEntry row .1.3.6.1.4.1.173.7.3.1.4.1

A list of configured values for an X25 port.

Indexes

nlIfRlp nlIfPhyPort nlIfPort

Column	Syntax	OID
portLogicalX25OperFrDlcimandatory The DLCI number used to identify the entry in the table. The range is 16-991.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.1.4.1.1
portLogicalX25OperCxnPrioritymandatory This field sets the priority of the connection among others on the physical port. The range is 0 for lowest priority to 9 for the highest priority.	Integer32 Constraints: range: 0-9	.1.3.6.1.4.1.173.7.3.1.4.1.2
portLogicalX25OperRfc1490mandatory This field indicates the encapsulation method used	Enumeration Enumerated Values: 1 annexG 2 rfc1490	.1.3.6.1.4.1.173.7.3.1.4.1.3
portLogicalX25OperBAGmandatory Assigns this DLCI to one of sixteen groups whose parameters regulate bandwidth usage.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.173.7.3.1.4.1.4

This table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
          
Most of the objects in this read-write table have
corresponding read-only objects in the
portX25OperTable that return the current
operating value.
          
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started.

portX25AdminEntry row .1.3.6.1.4.1.173.7.3.1.5.1

A list of configured values for an X25 port.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portX25AdminBlockedFlagmandatory A flag which when set, means the port should not be enabled after a boot-up of the node.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.1
portX25AdminFlowCtrlNegmandatory A flag which if set, permits negotiation of the flow control parameters on a per call basis. If N is selected, the default packet and window sizes will be used. If Y is selected, the packet or window size in a call pack…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.2
portX25AdminThruptClassNegmandatory A flag which ,if set, permists negotiation of the throughput class for either direction of data transmission on a per call basis. If N is selected, the configured Max Throughput Class value is used. If Y, any throughpu…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.3
portX25AdminLocChgPrevmandatory If Y is selected, no calls can be charged to port. Incoming calls from the network with reverse charge specified will be rejected. Outgoing calls will insert reverse charge in the call packet if not already included.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.4
portX25AdminRevChgAccptmandatory A flag, if set, that authorizes transmission of incoming calls that request the reverse charge facility. If N is selected, and a call requests it, it will not be transmitted.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.5
portX25AdminFastSelAccptmandatory A flag, if set, that authorizes transmission of incoming calls that request the Fast Select facility.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.6
portX25AdminInCallBarmandatory An X25 facility that prevents transmission of incoming calls to the local DTE.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.7
portX25AdminOutCallBarmandatory An X25 facility that prevents transmission of incoming calls to the local DTE.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.8
portX25AdminMaxPktSizemandatory The maximum data packet size that will be allowed to pass through this port.	Integer32r/w Constraints: range: 128-4096	.1.3.6.1.4.1.173.7.3.1.5.1.9
portX25AdminDefPktSizemandatory This is the size that will be assigned to an incoming call setup packet if the packet does not request a packet size.	Integer32r/w Constraints: range: 16-4096	.1.3.6.1.4.1.173.7.3.1.5.1.10
portX25AdminMaxWinSizemandatory This is the maximum number of unacknowledged packets per logical channel that can pass through this port.	Integer32r/w Constraints: range: 2-7	.1.3.6.1.4.1.173.7.3.1.5.1.11
portX25AdminDefWinSizemandatory This size will be assigned to an incoming call setup packet if the packet doesn't request a window size.	Integer32r/w Constraints: range: 1-7	.1.3.6.1.4.1.173.7.3.1.5.1.12
portX25AdminMaxThruptClassmandatory This specifies the default throughput class that will be inserted into a Call Request packet if Thruput Class negotiation is not enabled or if a thruput class is not requested in the call request.	Integer32r/w Constraints: range: 3-13	.1.3.6.1.4.1.173.7.3.1.5.1.13
portX25AdminCUGPrefmandatory This flag, if set, indicates the port belongs to at least one CUG.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.14
portX25AdminCUGIndexmandatory This number is an index into a Closed User Group table which identifies the default Closed User Group for the port.	Integer32r/w Constraints: range: 1-100	.1.3.6.1.4.1.173.7.3.1.5.1.15
portX25AdminCUGIncAccessmandatory This flag, when set, indicates whether this port will be allowed to receive calls from outside its CUGs.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.16
portX25AdminCUGOutAccessmandatory This flag, when set, indicates whether this port will be allowed to make calls outside its CUGs.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.5.1.17

This table contains Netlink Enterprise specific
objects to manage an X25 port. Changing one of
these parameters may take effect in the operating
port immediately or may wait until the interface is
restarted depending on the details of the
implementation.
          
The objects in this read-only table 
corresponding read-only objects in the
portX25OperTable that return the current
operating value.
          
The operating values may be different from these
configured values if a configured parameter was
configured after the interface was started.

portX25OperEntry row .1.3.6.1.4.1.173.7.3.1.6.1

A list of configured values for an X25 port.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portX25OperBlockedFlagmandatory A flag which when set, means the port should not be enabled after a boot-up of the node.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.1
portX25OperFlowCtrlNegmandatory A flag which if set, permits negotiation of the flow control parameters on a per call basis. If N is selected, the default packet and window sizes will be used. If Y is selected, the packet or window size in a call pack…	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.2
portX25OperThruptClassNegmandatory A flag which ,if set, permists negotiation of the throughput class for either direction of data transmission on a per call basis. If N is selected, the configured Max Throughput Class value is used. If Y, any throughpu…	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.3
portX25OperLocChgPrevmandatory If Y is selected, no calls can be charged to port. Incoming calls from the network with reverse charge specified will be rejected. Outgoing calls will insert reverse charge in the call packet if not already included.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.4
portX25OperRevChgAccptmandatory A flag, if set, that authorizes transmission of incoming calls that request the reverse charge facility. If N is selected, and a call requests it, it will not be transmitted.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.5
portX25OperFastSelAccptmandatory A flag, if set, that authorizes transmission of incoming calls that request the Fast Select facility.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.6
portX25OperInCallBarmandatory An X25 facility that prevents transmission of incoming calls to the local DTE.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.7
portX25OperOutCallBarmandatory An X25 facility that prevents transmission of incoming calls to the local DTE.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.8
portX25OperMaxPktSizemandatory The maximum data packet size that will be allowed to pass through this port.	Integer32 Constraints: range: 128-4096	.1.3.6.1.4.1.173.7.3.1.6.1.9
portX25OperDefPktSizemandatory This is the size that will be assigned to an incoming call setup packet if the packet does not request a packet size.	Integer32 Constraints: range: 16-4096	.1.3.6.1.4.1.173.7.3.1.6.1.10
portX25OperMaxWinSizemandatory This is the maximum number of unacknowledged packets per logical channel that can pass through this port.	Integer32 Constraints: range: 2-7	.1.3.6.1.4.1.173.7.3.1.6.1.11
portX25OperDefWinSizemandatory This size will be assigned to an incoming call setup packet if the packet doesn't request a window size.	Integer32 Constraints: range: 1-7	.1.3.6.1.4.1.173.7.3.1.6.1.12
portX25OperMaxThruptClassmandatory This specifies the default throughput class that will be inserted into a Call Request packet if Thruput Class negotiation is not enabled or if a thruput class is not requested in the call request.	Integer32 Constraints: range: 3-13	.1.3.6.1.4.1.173.7.3.1.6.1.13
portX25OperCUGPrefmandatory This flag, if set, indicates the port belongs to at least one CUG.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.14
portX25OperCUGIndexmandatory This number is an index into a Closed User Group table which identifies the default Closed User Group for the port.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.173.7.3.1.6.1.15
portX25OperCUGIncAccessmandatory This flag, when set, indicates whether this port will be able to receive calls from outside its CUGs.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.16
portX25OperCUGOutAccessmandatory This flag, when set, indicates whether this port will be able to make calls outside its CUGs.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.1.6.1.17

A list of Frame Relay ports .  The number of
entries will be the number of Frame Relay ports on the node.

portFrEntry row .1.3.6.1.4.1.173.7.3.2.1.1

An Frame Relay Port entry containing objects
relating to the port that are configurable
by the user.

Indexes

portFrRlpIndex portFrPortIndex

Column	Syntax	OID
portFrRlpIndexmandatory The RLP number of the Frame Relay port. It will be in the range 1-8.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.1.1.1
portFrPortIndexmandatory The Port number of the Frame Relay port. It will be in the range 1-8 for a physical port. It will be in the range 9-64 for a Frame Relay logical port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.1.1.2
portFrBlockedFlagmandatory A flag which when set, means the port should not be enabled after a boot-up of the node.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.3
portFrMaxBytesPerFramemandatory The maximum number of bytes allowed in an I Frame for this Frame Relay port.	Integer32r/w Constraints: range: 16-4096	.1.3.6.1.4.1.173.7.3.2.1.1.4
portFrT392Timermandatory This timer indicates how long the network will wait between Status Enquiry messages before recording an error. It should be greater than or equal to the frDlcmiPollingInterval variable in the RFC1315 Mib.	Integer32r/w Constraints: range: 5-30	.1.3.6.1.4.1.173.7.3.2.1.1.5
portFrOutgoingRateControlmandatory This is a flag which, when set, enables the enforcement of the Outgoing Rate Control parameters.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.6
portFrBandwidthAllocationmandatory This is a flag which, when set, enables whether the bandwidth allocation will be enforced.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.7
portFrConnectormandatory This defines the connector type of the Frame Relay port.	Enumerationr/w Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1 11 e1	.1.3.6.1.4.1.173.7.3.2.1.1.8
portFrLogicalDCEmandatory This defines the port as logical DCE or DTE.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.9
portFrGenClockmandatory This specifies whether the port will generate the clock necessary to synchronize traffic over the link.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.10
portFrRcvClkFrmDTEmandatory This allows the clock to be looped back from the DTE using the TT (Terminal Timing) signal, which can be helpful on high-speed lines.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.11
portFrLLMmandatory This determines whether, and what type of, configurable network management (status enquiries) will be allowed.	Enumerationr/w Enumerated Values: 1 none 2 lmi 3 annexd	.1.3.6.1.4.1.173.7.3.2.1.1.12
portFrRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portFrConfigTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', whic…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.2.1.1.13
portFrSpeedmandatory This object defines the speed of the Frame Relay port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not eq…	Integer32r/w Constraints: range: 75-2048000	.1.3.6.1.4.1.173.7.3.2.1.1.14
portFrBackupUseOnlymandatory This object determines whether all DLCIs on the port will be reserved exclusively as backups for other DLCIs in the same node. If yes is specified for this object, the port will remain disabled until needed for backup.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.1.1.15

A list of DLCI's on Frame Relay ports .  The number of
entries will be the number of DLCIs on all the Frame Relay
ports on a node.

portDLCIEntry row .1.3.6.1.4.1.173.7.3.2.2.1

An Frame Relay Port DLCI entry
relating to the Rate Control Information that is configurable
by the user.

Indexes

portDLCIRlpIndex portDLCIPortIndex portDLCIIndex

Column	Syntax	OID
portDLCIRlpIndexmandatory The RLP number on which the DLCI is located. The range for this is 1-8.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.2.1.1
portDLCIPortIndexmandatory The port number on which the DLCI is located. The range for this is 1-8 for a physical FR port and 9-64 for a logical FR port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.2.1.2
portDLCIIndexmandatory The DLCI number used to identify the entry in the table. The range is 16-991.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.2.1.3
portDLCIIncomingCIRmandatory The committed information rate that is supported on the DLCI for incoming data.	Integer32r/w Constraints: range: 0-2000	.1.3.6.1.4.1.173.7.3.2.2.1.4
portDLCIOutgoingCIRmandatory The committed information rate that is supported on the DLCI for outgoing data.	Integer32r/w Constraints: range: 0-2000	.1.3.6.1.4.1.173.7.3.2.2.1.5
portDLCIIncomingBcmandatory The committed burst size is the maximum amount of data to be transmitted under normal conditions within the time period defined by Bc/Cir that is supported on the DLCI for incoming data.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.2.1.6
portDLCIOutgoingBcmandatory The committed burst size is the maximum amount of data to be transmitted under normal conditions within the time period defined by Bc/Cir that is supported on the DLCI for Outgoing data.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.2.1.7
portDLCIIncomingBemandatory The excess burst size is the maximum amount of incoming data in excess of the committed burst size that the network will try to transfer during the time interval determined by Bc/Cir on this DLCI.	Integer32r/w Constraints: range: 0-32767	.1.3.6.1.4.1.173.7.3.2.2.1.8
portDLCIOutgoingBemandatory The excess burst size is the maximum amount of incoming data in excess of the committed burst size that the network will try to transfer during the time interval determined by Bc/Cir on this DLCI.	Integer32r/w Constraints: range: 0-32767	.1.3.6.1.4.1.173.7.3.2.2.1.9
portDLCIBecnRecoveryCntmandatory The BECN recovery Count is a method of controlling the rate of return to max traffic flow after it has been reduced due to congestion. The value determines the number of packets received sequentially without BECN set, b…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.2.2.1.10
portDLCIPrioritymandatory This field sets the priority of the DLCI among others on the physical port. The range is 0 for lowest priority to 4 for the highest priority.	Integer32r/w Constraints: range: 0-4	.1.3.6.1.4.1.173.7.3.2.2.1.11
portDLCIRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portDLCIConfigTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', wh…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.2.2.1.12
portDLCIBackupGroupmandatory This object specifies (if configured as any number other than zero) that this is a primary DLCI, and identifies the backup DLCI(s) (in a Frame Relay backup group) that will take over if this DLCI fails. This is applicab…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.2.2.1.13
portDLCIBackupProtEnbmandatory This object specifies whether the DLCI will be used as a non-initiating backup DLCI. The DLCI will wait for a backup protocol message from the initiating end, telling the backup where to send the rest of the messages.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.2.1.14

A Table describes the Frame Relay Backup MIB .

portFrBackupEntry row .1.3.6.1.4.1.173.7.3.2.3.1

This Entry contains the SNMP objects that are used for
configurating the Frame Relay Backup.

Indexes

portFrBackupRLP portFrBackupPort portFrBackupDLCI portFrBackupGroup

Column	Syntax	OID
portFrBackupRLPmandatory This RLP number identifies the RLP containing the primary and backup DLCIs.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.173.7.3.2.3.1.1
portFrBackupPortmandatory This Port number is the physical port on which the backup DLCI is being configured.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.173.7.3.2.3.1.2
portFrBackupDLCImandatory This DLCI number is the backup being configured.	Integer32 Constraints: range: 16-991	.1.3.6.1.4.1.173.7.3.2.3.1.3
portFrBackupGroupmandatory This Group number is the backup being configured.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.2.3.1.4
portFrBackupWaitTimermandatory This is the time after a primary DLCI failure that the software will wait for this DLCI to become active before checking the next backup DLCI. If the backup does not become active before the timer expires, the software …	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.173.7.3.2.3.1.5
portFrBackupProtEnabmandatory This enables or disables the backup protocol on the specified DLCI. It should be set to yes if and only if the remote device is an FRX4000 or FRX6000 with the backup protocol enabled on the remote DLCI connected to this…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.2.3.1.6
portFrBackupRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portFrBackupGroupTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active',…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.2.3.1.7

A list of BSC Interactive ports . The number of
entries will be the number of BSC Interactive ports on the node.

portBsciAdminEntry row .1.3.6.1.4.1.173.7.3.4.1.1

A BSCI Interactive Port entry containing objects
relating to the port that are configurable by the user.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portBsciAdminBlockedFlagmandatory Causes the port to be enabled or disabled at node IPL.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.173.7.3.4.1.1.1
portBsciAdminConnectormandatory Physical port interface connector type.	Enumerationr/w Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1	.1.3.6.1.4.1.173.7.3.4.1.1.2
portBsciAdminSpeedmandatory Data transmission rate in bits per second.	Integer32r/w Constraints: range: 75-19200	.1.3.6.1.4.1.173.7.3.4.1.1.3
portBsciAdminRetransmitIntervalmandatory Length of time before the node will transmit an I-frame if the previous transmission is not acknowledged.	Integer32r/w Constraints: range: 1-9999	.1.3.6.1.4.1.173.7.3.4.1.1.4
portBsciAdminMAXRetransmitsmandatory Maximum number of times the node will attempt to send an I-frame after a retransmission period expiration.	Integer32r/w Constraints: range: 1-99	.1.3.6.1.4.1.173.7.3.4.1.1.5
portBsciAdminMaxBytesPerFramemandatory Maximum frame size that will be transmitted on the port.	Integer32r/w Constraints: range: 25-4105	.1.3.6.1.4.1.173.7.3.4.1.1.6
portBsciAdminGenerateClockmandatory Specifies whether the port will generate the clock necessary to synchronize traffic over the link.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.7
portBsciAdminRcvClockFromDTEmandatory Allows the clock to be looped back from the DTE using the TT (Terminal Timing) signal.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.8
portBsciAdminPadTypemandatory BSCI Pad Type	Enumerationr/w Enumerated Values: 1 tpad 2 hpad	.1.3.6.1.4.1.173.7.3.4.1.1.9
portBsciAdminUseEBCDICmandatory Specifies whether all devices on a line use the same character set for successive session polls.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.10
portBsciAdminCallInfoInRequestPacketmandatory Specifies whether the user will have the option of including call information in a call request packet.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.11
portBsciAdminClearVCOnLastDeviceDownmandatory Causes the virtual circuit to be cleared when no terminals are using it.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.12
portBsciAdminTransTextSupportedmandatory Causes all characters transmitted to be treated as data.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.13
portBsciAdminEndToEndAckmandatory Allows management of acknowledgments end to end across the network rather than locally at each end.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.14
portBsciAdminFullDuplexmandatory Specifies full-duplex transmission.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.15
portBsciAdminMultidropmandatory Specifies whether transmission will be multidrop.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.16
portBsciAdminSlowPollRetryCountmandatory Specifies how many times the control unit will be polled before it is put on the slow poll list.	Integer32r/w Constraints: range: 10-150	.1.3.6.1.4.1.173.7.3.4.1.1.17
portBsciAdminSlowPollRetryFreqmandatory Specifies the number of times active control units will be polled between pollings on the slow poll list.	Integer32r/w Constraints: range: 1-200	.1.3.6.1.4.1.173.7.3.4.1.1.18
portBsciAdminStartSynchCharsmandatory Specifies the number of synchronization characters that will be added to the beginning of each frame.	Integer32r/w Constraints: range: 2-10	.1.3.6.1.4.1.173.7.3.4.1.1.19
portBsciAdminEndPadCharsmandatory Specifies the number of padding characters that will be added to the end of each frame.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.173.7.3.4.1.1.20
portBsciAdminPollIntervalmandatory Specifies the time between passes through the polling list.	Integer32r/w Constraints: range: 100-1000	.1.3.6.1.4.1.173.7.3.4.1.1.21
portBsciAdminNoResponseTimermandatory Activated after transmission of a general poll or a data frame.	Integer32r/w Constraints: range: 2-10	.1.3.6.1.4.1.173.7.3.4.1.1.22
portBsciAdminNoResponseRetryCountmandatory Specifies how many times the user device will be polled before control is passed on the next cluster.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.4.1.1.23
portBsciAdminErrorRetransmitCountmandatory Specifies the number of times the Netlink device will resend a block of data after the receiving device has detected an error in that block.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.4.1.1.24
portBsciAdminNAKRetryCountmandatory Specifies the number of times the Netlink device will send a frame when the receiving device is unable to acknowledge.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.4.1.1.25
portBsciAdminBlockCheckmandatory Sets the redundancy check parameter.	Enumerationr/w Enumerated Values: 1 crc16 2 even-lrc 3 odd-lrc	.1.3.6.1.4.1.173.7.3.4.1.1.26
portBsciAdminDataModemandatory Sets the parity parameter.	Enumerationr/w Enumerated Values: 1 odd-7bit 2 even-7bit 3 none-8bit	.1.3.6.1.4.1.173.7.3.4.1.1.27
portBsciAdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portBsciAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', whi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.4.1.1.28
portBsciAdminAnswerNonConfiguredmandatory Only valid if pad type is HPAD. If yes, the HPAD will respond to all devices on the line. If no, the HPAD will respond only to those devices that are configured on the node.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.29
portBsciAdminActivateConnectionWithoutPollmandatory Only valid if pad type is TPAD. If yes, will active the TPAD connection without a poll of the connected device.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.1.1.30

A list of BSC Interactive ports . The number of
entries will be the number of BSC Interactive ports on the node.

portBsciOperEntry row .1.3.6.1.4.1.173.7.3.4.2.1

A BSCI Interactive Port entry containing objects
relating to the port that are configurable by the user.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portBsciOperBlockedFlagmandatory Causes the port to be enabled or disabled at node IPL.	Enumeration Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.173.7.3.4.2.1.1
portBsciOperConnectormandatory Physical port interface connector type.	Enumeration Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1	.1.3.6.1.4.1.173.7.3.4.2.1.2
portBsciOperSpeedmandatory Data transmission rate in bits per second.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.4.2.1.3
portBsciOperRetransmitIntervalmandatory Length of time before the node will transmit an I-frame if the previous transmission is not acknowledged.	Integer32 Constraints: range: 1-9999	.1.3.6.1.4.1.173.7.3.4.2.1.4
portBsciOperMAXRetransmitsmandatory Maximum number of times the node will attempt to send an I-frame after a retransmission period expiration.	Integer32 Constraints: range: 1-99	.1.3.6.1.4.1.173.7.3.4.2.1.5
portBsciOperMaxBytesPerFramemandatory Maximum frame size that will be transmitted on the port.	Integer32 Constraints: range: 25-4105	.1.3.6.1.4.1.173.7.3.4.2.1.6
portBsciOperGenerateClockmandatory Specifies whether the port will generate the clock necessary to synchronize traffic over the link.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.7
portBsciOperRcvClockFromDTEmandatory Allows the clock to be looped back from the DTE using the TT (Terminal Timing) signal.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.8
portBsciOperPadTypemandatory BSCI Pad Type	Enumeration Enumerated Values: 1 tpad 2 hpad	.1.3.6.1.4.1.173.7.3.4.2.1.9
portBsciOperUseEBCDICmandatory Specifies whether all devices on a line use the same character set for successive session polls.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.10
portBsciOperCallInfoInRequestPacketmandatory Specifies whether the user will have the option of including call information in a call request packet.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.11
portBsciOperClearVCOnLastDeviceDownmandatory Causes the virtual circuit to be cleared when no terminals are using it.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.12
portBsciOperTransTextSupportedmandatory Causes all characters transmitted to be treated as data.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.13
portBsciOperEndToEndAckmandatory Allows management of acknowledgments end to end across the network rather than locally at each end.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.14
portBsciOperFullDuplexmandatory Specifies full-duplex transmission.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.15
portBsciOperMultidropmandatory Specifies whether transmission will be multidrop.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.16
portBsciOperSlowPollRetryCountmandatory Specifies how many times the control unit will be polled before it is put on the slow poll list.	Integer32 Constraints: range: 10-150	.1.3.6.1.4.1.173.7.3.4.2.1.17
portBsciOperSlowPollRetryFreqmandatory Specifies the number of times active control units will be polled between pollings on the slow poll list.	Integer32 Constraints: range: 1-200	.1.3.6.1.4.1.173.7.3.4.2.1.18
portBsciOperStartSynchCharsmandatory Specifies the number of synchronization characters that will be added to the beginning of each frame.	Integer32 Constraints: range: 2-10	.1.3.6.1.4.1.173.7.3.4.2.1.19
portBsciOperEndPadCharsmandatory Specifies the number of padding characters that will be added to the end of each frame.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.173.7.3.4.2.1.20
portBsciOperPollIntervalmandatory Specifies the time between passes through the polling list.	Integer32 Constraints: range: 100-1000	.1.3.6.1.4.1.173.7.3.4.2.1.21
portBsciOperNoResponseTimermandatory Activated after transmission of a general poll or a data frame.	Integer32 Constraints: range: 2-10	.1.3.6.1.4.1.173.7.3.4.2.1.22
portBsciOperNoResponseRetryCountmandatory Specifies how many times the user device will be polled before control is passed on the next cluster.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.4.2.1.23
portBsciOperErrorRetransmitCountmandatory Specifies the number of times the Netlink device will resend a block of data after the receiving device has detected an error in that block.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.4.2.1.24
portBsciOperNAKRetryCountmandatory Specifies the number of times the Netlink device will send a frame when the receiving device is unable to acknowledge.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.173.7.3.4.2.1.25
portBsciOperBlockCheckmandatory Sets the redundancy check parameter.	Enumeration Enumerated Values: 1 crc16 2 even-lrc 3 odd-lrc	.1.3.6.1.4.1.173.7.3.4.2.1.26
portBsciOperDataModemandatory Sets the parity parameter.	Enumeration Enumerated Values: 1 odd-7bit 2 even-7bit 3 none-8bit	.1.3.6.1.4.1.173.7.3.4.2.1.27
portBsciOperAnswerNonConfiguredmandatory Only valid if pad type is HPAD. If yes, the HPAD will respond to all devices on the line. If no, the HPAD will respond only to those devices that are configured on the node.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.28
portBsciOperActivateConnectionWithoutPollmandatory Only valid if pad type is TPAD. If yes, will active the TPAD connection without a poll of the connected device.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.2.1.29

A list of BSC Interactive port subscribers.

bsciSubscrAdminEntry row .1.3.6.1.4.1.173.7.3.4.3.1

A BSCI Interactive Port Subscriber entry containing objects
relating to the port that are configurable by the user.

Indexes

nlIfRlp nlIfPort bsciSubscrAdminSequence

Column	Syntax	OID
bsciSubscrAdminSequencemandatory Subscriber index for a specific BSCI port subscriber.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.173.7.3.4.3.1.1
bsciSubscrAdminLocalIDmandatory Subscriber address of the local end of a BSCI connection.	NlSubscriberAddressr/w Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.4.3.1.2
bsciSubscrAdminRemoteIDmandatory Subscriber address of the remote end of a BSCI connection.	NlSubscriberAddressr/w Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.4.3.1.3
bsciSubscrAdminAutocallmandatory Causes a BSCI TPAD to automatically call its HPAD when the controller becomes active.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.3.1.4
bsciSubscrAdminAutocallRtyTimermandatory Time between autocall retries.	Integer32r/w Constraints: range: 15-255	.1.3.6.1.4.1.173.7.3.4.3.1.5
bsciSubscrAdminAutocallMaxRtrymandatory Maximum number of times an autocall will be sent.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.4.3.1.6
bsciSubscrAdminConnectionIDmandatory Identifier that will link the BSCI port with a device configured in the BSCI Devices Table.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.4.3.1.7
bsciSubscrAdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the bsciDevAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', whic…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.4.3.1.8

A list of BSC Interactive port subscribers.

bsciSubscrOperEntry row .1.3.6.1.4.1.173.7.3.4.4.1

A BSCI Interactive Port Subscriber entry containing objects
relating to the port that are configurable by the user.

Indexes

nlIfRlp nlIfPort bsciSubscrOperSequence

Column	Syntax	OID
bsciSubscrOperSequencemandatory Subscriber index for a specific BSCI port subscriber.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.173.7.3.4.4.1.1
bsciSubscrOperLocalIDmandatory Subscriber address of the local end of a BSCI connection.	NlSubscriberAddress Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.4.4.1.2
bsciSubscrOperRemoteIDmandatory Subscriber address of the remote end of a BSCI connection.	NlSubscriberAddress Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.4.4.1.3
bsciSubscrOperAutocallmandatory Causes a BSCI TPAD to automatically call its HPAD when the controller becomes active.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.4.1.4
bsciSubscrOperAutocallRtyTimermandatory Time between autocall retries.	Integer32 Constraints: range: 15-255	.1.3.6.1.4.1.173.7.3.4.4.1.5
bsciSubscrOperAutocallMaxRtrymandatory Maximum number of times an autocall will be sent.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.4.4.1.6
bsciSubscrOperConnectionIDmandatory Identifier that will link the BSCI port with a device configured in the BSCI Devices Table.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.4.4.1.7

A list of BSC Interactive devices.

bsciDevAdminEntry row .1.3.6.1.4.1.173.7.3.4.5.1

A BSCI Interactive Device entry containing objects
relating to the device that are configurable by the user.

Indexes

nlIfRlp nlIfPort bsciDevAdminControlUnitID bsciDevAdminDeviceUnitID

Column	Syntax	OID
bsciDevAdminControlUnitIDmandatory Control Unit identifier.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.173.7.3.4.5.1.1
bsciDevAdminDeviceUnitIDmandatory Device Unit identifier.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.173.7.3.4.5.1.2
bsciDevAdminConnectionIDmandatory The BSCI port connection ID for the device.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.4.5.1.3
bsciDevAdminSingleUserVCmandatory Specifies whether each end of the connection is within a same Control Unit/Device Type pair.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.5.1.4
bsciDevAdminTransTextSupportedmandatory Causes all characters transmitted to be treated as data.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.5.1.5
bsciDevAdminPrinterAttachedmandatory Specifies whether the device has a printer attached.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.5.1.6
bsciDevAdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the bsciDevAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', whic…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.4.5.1.7
bsciDevAdminDisableStatusRequestmandatory Determines how the BSCI port will report the status of the attached device. Normal status- the port will report what the device reports. No status- the port will report status only if the device is active. Always act…	Enumerationr/w Enumerated Values: 1 normal 2 none 3 always-active	.1.3.6.1.4.1.173.7.3.4.5.1.8

A list of BSC Interactive devices.

bsciDevOperEntry row .1.3.6.1.4.1.173.7.3.4.6.1

A BSCI Interactive Device entry containing objects
relating to the device that are configurable by the user.

Indexes

nlIfRlp nlIfPort bsciDevOperControlUnitID bsciDevOperDeviceUnitID

Column	Syntax	OID
bsciDevOperControlUnitIDmandatory Control Unit identifier.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.173.7.3.4.6.1.1
bsciDevOperDeviceUnitIDmandatory Device Unit identifier.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.173.7.3.4.6.1.2
bsciDevOperConnectionIDmandatory The BSCI port connection ID for the device.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.4.6.1.3
bsciDevOperSingleUserVCmandatory Specifies whether each end of the connection is within a same Control Unit/Device Type pair.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.6.1.4
bsciDevOperTransTextSupportedmandatory Causes all characters transmitted to be treated as data.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.6.1.5
bsciDevOperPrinterAttachedmandatory Specifies whether the device has a printer attached.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.4.6.1.6
bsciDevOperDisableStatusRequestmandatory Determines how the BSCI port will report the status of the attached device. Normal status- the port will report what the device reports. No status- the port will report status only if the device is active. Always act…	Enumeration Enumerated Values: 1 normal 2 none 3 always-active	.1.3.6.1.4.1.173.7.3.4.6.1.7

This table contains Netlink Enterprise specific
objects to manage SDLC port. Changing on of the
these parameters may take effect in the operating
port immediately or may wait until the interface is                             restarted depending on the details of the 
implementation.
          
Most of the objects in this read-write table have 
corresponding read-only objects in the 
portSdlcOperTable that return the current 
operating value.
          
The operating values may be different from these 
configured values if a configured parameter was 
configured afterthe interface was started.

portSdlcAdminEntry row .1.3.6.1.4.1.173.7.3.5.1.1

A list of configured values for an SDLC port.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portSdlcAdminCommitobsolete Writing a value to this object commits the the SDLC port related modified configuration values to the database.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.5.1.1.1
portSdlcAdminMAXRetriesmandatory This object defines the max. number of retries to a non-responding Link station, before putting the Link station to slow-poll list if it is not Normal response Mode OR disconnecting the link station if it is data txfr …	Integer32r/w Constraints: range: 0-99	.1.3.6.1.4.1.173.7.3.5.1.1.2
portSdlcAdminMAXOutmandatory This object defines the number of outstanding frames for triggering window full condition.	Integer32r/w Constraints: range: 1-7	.1.3.6.1.4.1.173.7.3.5.1.1.3
portSdlcAdminPadTypemandatory This object defines the SNA PAD types.	Enumerationr/w Enumerated Values: 1 xpad 2 tpad 3 hpad 4 npad	.1.3.6.1.4.1.173.7.3.5.1.1.4
portSdlcAdminGenerateClockmandatory This object defines if the port would generate clock.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.1.1.5
portSdlcAdminRcvClockFromDTEmandatory This object defines if the rcv clock will be used from DTE.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.1.1.6
portSdlcAdminNrzmandatory This object defines the data encoding at the physical layer	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.1.1.7
portSdlcAdminPacketSizemandatory This object defines the packet size of the X25 layer used by SNA PAD	Integer32r/w Constraints: range: 16-4096	.1.3.6.1.4.1.173.7.3.5.1.1.8
portSdlcAdminDisableRequestDisconnectmandatory This object defines if a Request To Disconnect(RD) will be sent when remote PAD clear the connection	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.1.1.9
portSdlcAdminLPDASupportmandatory This object defines the type LPDA support on SDLC port.	Enumerationr/w Enumerated Values: 1 none 2 lpda-1 3 lpda-2	.1.3.6.1.4.1.173.7.3.5.1.1.10
portSdlcAdminConnectormandatory This object defines the connector type of the SDLC port.	Enumerationr/w Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1	.1.3.6.1.4.1.173.7.3.5.1.1.11
portSdlcAdminSpeedmandatory This object defines the speed of the SDLC port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to…	Integer32r/w Constraints: range: 75-2048000	.1.3.6.1.4.1.173.7.3.5.1.1.12
portSdlcAdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the portSdlcAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', whi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.5.1.1.13
portSdlcAdminIdleFillCharmandatory This object specifies a character that wll be inserted into the stream when the SNA link is idle.	Enumerationr/w Enumerated Values: 1 hex-ff 2 hex-7e	.1.3.6.1.4.1.173.7.3.5.1.1.14
portSdlcAdminInactivityTimermandatory This object determines how long the node will wait with no activity on the port before it will declare the attached device down.	Integer32r/w Constraints: range: 15-250	.1.3.6.1.4.1.173.7.3.5.1.1.15
portSdlcAdminL1Duplexmandatory This object determines whether level-1 (physical layer) transmission can be in one (half duplex) or both (full duplex) directions at once.	Enumerationr/w Enumerated Values: 1 full-duplex 2 half-duplex	.1.3.6.1.4.1.173.7.3.5.1.1.16

This table contains current Netlink enterprise specific
port parameters

portSdlcOperEntry row .1.3.6.1.4.1.173.7.3.5.2.1

A list of operational values for an SDLC port.

Indexes

nlIfRlp nlIfPort

Column	Syntax	OID
portSdlcOperCommitobsolete This object is not used.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.5.2.1.1
portSdlcOperMAXRetriesmandatory This object defines the max. number of retries to a non-responding Link station, before putting the Link station to slow-poll list if it is not Normal response Mode OR disconnecting the link station if it is data txfr …	Integer32 Constraints: range: 0-99	.1.3.6.1.4.1.173.7.3.5.2.1.2
portSdlcOperMAXOutmandatory This object defines the number of outstanding frames for triggering window full condition.	Integer32 Constraints: range: 1-7	.1.3.6.1.4.1.173.7.3.5.2.1.3
portSdlcOperPadTypemandatory This object defines the SNA PAD type	Enumeration Enumerated Values: 1 xpad 2 tpad 3 hpad 4 npad	.1.3.6.1.4.1.173.7.3.5.2.1.4
portSdlcOperGenerateClockmandatory This object defines if the port would generate clock.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.2.1.5
portSdlcOperRcvClockFromDTEmandatory This object defines if the rcv clock will be used from DTE.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.2.1.6
portSdlcOperNrzmandatory This object defines the data encoding at the physical layer	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.2.1.7
portSdlcOperPacketSizemandatory This object defines the packet size of the X25 layer used by SNA PAD	Integer32 Constraints: range: 16-4096	.1.3.6.1.4.1.173.7.3.5.2.1.8
portSdlcOperDisableRequestDisconnectmandatory This object defines if a Request To Disconnect(RD) will be sent when remote PAD clear the connection	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.2.1.9
portSdlcOperLPDASupportmandatory This object defines the type LPDA support on SDLC port.	Enumeration Enumerated Values: 1 none 2 lpda-1 3 lpda-2	.1.3.6.1.4.1.173.7.3.5.2.1.10
portSdlcOperConnectormandatory This object defines the operational connector type of the SDLC port.	Enumeration Enumerated Values: 3 rs232 5 v35 6 rs449 7 rs530 8 x21 10 t1	.1.3.6.1.4.1.173.7.3.5.2.1.11
portSdlcOperSpeedmandatory This object defines the operational speed of the SDLC port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.173.7.3.5.2.1.12
portSdlcOperIdleFillCharmandatory This object specifies a character that wll be inserted into the stream when the SNA link is idle.	Enumeration Enumerated Values: 1 hex-ff 2 hex-7e	.1.3.6.1.4.1.173.7.3.5.2.1.13
portSdlcOperInactivityTimermandatory This object determines how long the node will wait with no activity on the port before it will declare the attached device down.	Integer32 Constraints: range: 15-250	.1.3.6.1.4.1.173.7.3.5.2.1.14
portSdlcOperL1Duplexmandatory This object determines whether level-1 (physical layer) transmission can be in one (half duplex) or both (full duplex) directions at once.	Enumeration Enumerated Values: 1 full-duplex 2 half-duplex	.1.3.6.1.4.1.173.7.3.5.2.1.15

This table contains Enterprise specific Link station
configurable parameters to manage the link stations.

lSSdlcAdminEntry row .1.3.6.1.4.1.173.7.3.5.3.1

A list of configured values for an SDLC port.

Indexes

nlIfRlp nlIfPort sdlcLSAddress

Column	Syntax	OID
lSSdlcAdminLocalSubmandatory This object defines the local subscriber ID of the Link Station	NlSubscriberAddressr/w Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.5.3.1.1
lSSdlcAdminRemoteSubmandatory This object defines the remote subscriber ID used to connect to remote Link Station	NlSubscriberAddressr/w Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.5.3.1.2
lSSdlcAdminAutoCallmandatory This object defines if auto call is enabled for the link station. If enabled, the link station will initiate connection establishment, when appropriate. Else, it will passively listen to the connection request for estab…	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.3.1.3
lSSdlcAdminRetryTimemandatory This object is used, only when lSSdlcAdminAutoCall object is yes. This defines the time interval measured in seconds in which the connection request is retried	Integer32r/w Constraints: range: 15-225	.1.3.6.1.4.1.173.7.3.5.3.1.4
lSSdlcAdminRetryCountmandatory This object is used, only when lSSdlcAdminAutoCall object is yes. This defines the number of times the connection initiation is retried before given up. The value of Zero(0) means to try indefinitely	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.5.3.1.5
lSSdlcAdminLlc2Conversionmandatory This object defines if this link station connects to a LLC2 device/host.	Enumerationr/w Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.3.1.6
lSSdlcAdminLPDAResourceIDmandatory This objects the resource ID used during LPDA command support	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.5.3.1.7
lSSdlcAdminRowStatusmandatory This variable is used to manage the creation and deletion of conceptual rows in the lSSdlcAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.173.7.3.5.3.1.8
lSSdlcAdminL2DatModemandatory This object determines whether transmission can be in one (alternate) or two (simultaneous) directions at the same time.	Enumerationr/w Enumerated Values: 1 two-way-alternate 2 two-way-simultaneous	.1.3.6.1.4.1.173.7.3.5.3.1.9

This table contains the operational parameters of the
SDLC port

lSSdlcOperEntry row .1.3.6.1.4.1.173.7.3.5.4.1

A list of configured values for an SDLC port.

Indexes

nlIfRlp nlIfPort sdlcLSAddress

Column	Syntax	OID
lSSdlcOperLocalSubmandatory This object defines the local subscriber ID of the Link Station	NlSubscriberAddress Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.5.4.1.1
lSSdlcOperRemoteSubmandatory This object defines the remote subscriber ID used to connect to remote Link Station	NlSubscriberAddress Type Constraints: range: 1..15	.1.3.6.1.4.1.173.7.3.5.4.1.2
lSSdlcOperAutoCallmandatory This object defines if auto call is enabled for the link station. If enabled, the link station will initiate connection establishment, when appropriate. Else, it will passively listen to the connection request for estab…	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.4.1.3
lSSdlcOperRetryTimemandatory This object is valid, only when lSSdlcAdminAutoCall object is yes. This defines the time interval measured in seconds in which the connection request is retried	Integer32 Constraints: range: 15-225	.1.3.6.1.4.1.173.7.3.5.4.1.4
lSSdlcOperRetryCountmandatory This object is used, only when lSSdlcAdminAutoCall object is yes. This defines the number of times the connection initiation is retried before given up. The value of Zero(0) means to try indefinitely	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.5.4.1.5
lSSdlcOperLlc2Conversionmandatory This object defines if this link station connects to a LLC2 device/host.	Enumeration Enumerated Values: 1 no 2 yes	.1.3.6.1.4.1.173.7.3.5.4.1.6
lSSdlcOperLPDAResourceIDmandatory This objects the resource ID used during LPDA command support	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.173.7.3.5.4.1.7
lSSdlcOperL2DatModemandatory This object determines whether transmission can be in one (alternate) or two (simultaneous) directions at the same time.	Enumeration Enumerated Values: 1 two-way-alternate 2 two-way-simultaneous	.1.3.6.1.4.1.173.7.3.5.4.1.8