MOXA-NP6000-MIB Table View

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.1

spanningTreePortEnable

This enable of spanning tree protocol for this port.
Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC
do not support write access.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.2

spanningTreePortPriority

The port priority of spanning tree protocol.
Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC
do not support write access.

Enumerationr/w

Enumerated Values:

0	priority-0
16	priority-16
32	priority-32
48	priority-48
64	priority-64
80	priority-80
96	priority-96
112	priority-112
128	priority-128
144	priority-144
160	priority-160
176	priority-176
192	priority-192
208	priority-208
224	priority-224
240	priority-240

.1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.3

spanningTreePortCost

The port cost of spanning tree protocol. Range is 1~20000000.
Note: NPort 6150, 6250, 6250-S-SC, 6250-M-SC
do not support write access.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.3.15.1.2.5.1.4

deviceControlTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1 · 1 row entry · 21 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk deviceControlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::deviceControlTable'

The Device Control application table.

deviceControlEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1

The Device Control application entry.

Indexes

deviceControlTcpAliveCheck

Column Syntax OID

The TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort 6000 series device server
automatically closes the TCP connection if there is
no TCP activity fo…

deviceControlMaxConnection

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.1

Max connection is usually used when the user needs
to receive data from different hosts simultaneously.
The factory default is 1. In this case, only one
specific host can access this port of the NPort 6000
series device…

deviceControlIgnoreJammedIp

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.2

Previously, when Max connection was set to a value
greater than 1, and the serial device was
transmitting data, if any one of the connected hosts
stopped responding, the serial device would wait
until the data had been …

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.3

deviceControlAllowDriverControl

If Max connection is greater than 1, NPort will
ignore driver control commands from all connected
hosts. However, if you set Allow driver control to
YES, control commands will be accepted. Note that
since the NPort 6000…

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.4

deviceControlCommandByCommandOperation

Commands will be sent from the NPort to the
serial device. After each command, the NPort will wait to
receive a response before sending the next command.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.5

deviceControlSecure

If 'Secure' is enabled, the data on the Ethernet
will be encrypted with SSL.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.6

deviceControlConnectionDownRTS

For some applications, serial devices must obtain
the Ethernet link status by reading the RTS signal from the
NPort 6000 series device server. If this setting is
set to 'always low,' RTS will change its state to
low if …

Enumerationr/w

Enumerated Values:

0	always-high
1	always-low

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.7

deviceControlConnectionDownDTR

For some applications, serial devices must obtain
the Ethernet link status by reading the DTR signal from the
NPort 6000 series device server. If this setting is
set to 'goes low,' DTR will change its state to
low if th…

Enumerationr/w

Enumerated Values:

0	always-high
1	always-low

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.8

deviceControlResponseTimeout

After sending a command to the serial device, the NPort
will wait for a response. If no response is received from
the serial device within the specified time, the NPort will
give up and continue to the next command.

deviceControlNonRequestSerialData

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.9

This specifies how the NPort will handle data that is
received from a serial device that is not a response to
a command. The NPort can either discard such data, forward
the data to the network host that sent the most…

Enumerationr/w

Enumerated Values:

0	discard
1	forward-to-last-requester
2	forward-to-all-open-connections

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.10

deviceControlTcpPort

The 'TCP port' is the TCP port that the NPort
6000 series device server uses to listen to
connections, and that other devices must use to
contact the NPort 6000 series device server.
This setting is used in RFC2217 mode.

deviceControlDestinationAddress1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.11

The NPort 6000 series device server can connect actively
to a remote host that has this IP address.
This setting is used in Reverse RealCOM mode.

deviceControlDestinationTcpPort1

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.12

The NPort 6000 series device server can connect actively
to a remote host that has this TCP data port number.
This setting is used in Reverse RealCOM mode.

deviceControlDestinationCmdPort1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.13

The NPort 6000 series device server can connect actively
to a remote host that has this TCP command port number.
This setting is used in Reverse RealCOM mode.

deviceControlDestinationAddress2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.14

The NPort 6000 series device server can connect actively
to a remote host that has this IP address.
This setting is used in Reverse RealCOM mode.

deviceControlDestinationTcpPort2

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.15

The NPort 6000 series device server can connect actively
to a remote host that has this TCP data port number.
This setting is used in Reverse RealCOM mode.

deviceControlDestinationCmdPort2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.16

The NPort 6000 series device server can connect actively
to a remote host that has this TCP command port number.
This setting is used in Reverse RealCOM mode.

deviceControlDesignatedLocalTcpPort1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.17

The local TCP data port used to connect actively to the
remote host. This setting is used in Reverse RealCOM mode.

deviceControlDesignatedLocalCmdPort1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.18

The local TCP command port used to connect actively to the
remote host. This setting is used in Reverse RealCOM mode.

deviceControlDesignatedLocalTcpPort2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.19

The local TCP data port used to connect actively to the
remote host. This setting is used in Reverse RealCOM mode.

deviceControlDesignatedLocalCmdPort2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.20

The local TCP command port used to connect actively to the
remote host. This setting is used in Reverse RealCOM mode.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.21

socketTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1 · 1 row entry · 41 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk socketTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::socketTable'

The Socket application table.

socketEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1

The Socket application entry.

Indexes

Column Syntax OID

socketTcpAliveCheck

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.1

socketInactivityTime

0 ms: TCP connection is not closed when the
serial line is idle.
1-65535 ms: The NPort 6000 series device server
automatically closes the TCP connection if there is
no serial data activity for the given time. After
the …

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.2

socketMaxConnection

socketCommandByCommandOperation

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.3

socketIgnoreJammedIp

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.4

socketAllowDriverControl

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.5

Commands will be sent from the NPort to the
serial device. After each command, the NPort will wait to
receive a response before sending the next command.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.6

socketSecure

If Secure is enabled, data sent over the Ethernet will be
encrypted with SSL.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.7

socketTcpPort

The 'TCP port' is the TCP port that the NPort
6000 series device server uses to listen to
connections, and that other devices must use to
contact the NPort 6000 series device server.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.8

socketCmdPort

The 'Command port' is a TCP port used to listen for
IP-Serial Lib commands from the host. In order to
prevent a TCP port conflict with other applications,
the user can set the Command port to another port
if needed. IP…

socketTcpServerConnectionDownRTS

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.9

For some applications, serial devices must obtain
the Ethernet link status from the RTS signal sent by the
NPort 6000 series device server. If this setting is
set to 'goes low,' RTS will change the state to
low if the E…

Enumerationr/w

Enumerated Values:

0	always-high
1	always-low

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.10

socketTcpServerConnectionDownDTR

For some applications, serial devices must obtain
the Ethernet link status from the DTR signal sent by the
NPort 6000 series device server. If this setting is
set to 'goes low,' DTR will change the state to
low if the E…

Enumerationr/w

Enumerated Values:

0	always-high
1	always-low

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.11

socketResponseTimeout

socketNonRequestSerialData

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.12

Enumerationr/w

Enumerated Values:

0	discard
1	forward-to-last-requester
2	forward-to-all-open-connections

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.13

socketTcpClientDestinationAddress1

The NPort 6000 series device server can connect actively
to a remote host that has this IP address.

socketTcpClientDestinationPort1

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.14

The NPort 6000 series device server can connect actively
to a remote host that has this TCP port number.

socketTcpClientDestinationAddress2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.15

The NPort 6000 series device server can
connect actively to a remote host that has this IP
address.

socketTcpClientDestinationPort2

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.16

The NPort 6000 series device server can
connect actively to a remote host that
has this TCP port number.

socketTcpClientDestinationAddress3

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.17

The NPort 6000 series device server can
connect actively to a remote host that
has this IP address.

socketTcpClientDestinationPort3

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.18

The NPort 6000 series device server can
connect actively to a remote host that
has this port number.

socketTcpClientDestinationAddress4

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.19

The NPort 6000 series device server can
connect actively to a remote host that
has this IP address.

socketTcpClientDestinationPort4

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.20

The NPort 6000 series device server can
connect actively to a remote host that
has this port number.

socketTcpClientDesignatedLocalPort1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.21

The local TCP port used to connect actively to the
remote host.

socketTcpClientDesignatedLocalPort2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.22

The local TCP port used to connect actively to the
remote host.

socketTcpClientDesignatedLocalPort3

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.23

The local TCP port used to connect actively to the
remote host.

socketTcpClientDesignatedLocalPort4

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.24

The local TCP port used to connect actively to the
remote host.

socketTcpClientConnectionControl

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.25

Events that cause the TCP client to drop the
connection.

Enumerationr/w

Enumerated Values:

257	startup-None
258	anyCharacter-None
260	dsrOn-None
264	dcdOn-None
514	anyCharacter-InactivityTime
1028	dsrOn-DSR-Off
2056	dcdOn-DCD-Off

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.26

socketUdpDestinationAddress1Begin

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between this parameter and
socketUdpDestinationAddress1End.

socketUdpDestinationAddress1End

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.27

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between
socketUdpDestinationAddress1Begin and this parameter.

socketUdpDestinationPort1

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.28

The NPort 6000 series device server can actively send
UDP packets to remote hosts that have this port
number.

socketUdpDestinationAddress2Begin

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.29

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between this parameter and
socketUdpDestinationAddress2End.

socketUdpDestinationAddress2End

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.30

The NPort 6000 series device server can actively send
UDP packets to the remote hosts whose IP
addresses are in the range between
socketUdpDestinationAddress2Begin and this parameter.

socketUdpDestinationPort2

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.31

The NPort 6000 series device server can actively send
UDP packets to the remote hosts that have this
TCP port number.

socketUdpDestinationAddress3Begin

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.32

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between this parameter and
socketUdpDestinationAddress3End.

socketUdpDestinationAddress3End

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.33

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between
socketUdpDestinationAddress3Begin and this parameter.

socketUdpDestinationPort3

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.34

The NPort 6000 series device server can actively send
UDP packets to remote hosts that have this
TCP port number.

socketUdpDestinationAddress4Begin

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.35

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between this parameter and
socketUdpDestinationAddress4End.

socketUdpDestinationAddress4End

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.36

The NPort 6000 series device server can actively send
UDP packets to remote hosts whose IP
addresses are in the range between
socketUdpDestinationAddress4Begin and this parameter.

socketUdpDestinationPort4

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.37

The NPort 6000 series device server can actively send
UDP packets to remote hosts that have this
TCP port number.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.38

socketUdpLocalListenPort

The UDP port that the NPort 6000 series device
server listens to and that other devices must use
to contact the NPort 6000 series device server.

socketUDPDynamicDstTimeout

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.39

socketUDPDynamicDst

If enable Dynamic Destination,
the target address is decieded by the source
address of the last received data.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.40

0 ms: The target address will be changed every time.
1-65535 ms: The target address will be occupied before the
source address idle for a period of time.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.41

pairConnectionTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk pairConnectionTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::pairConnectionTable'

The Pair Connection table.

pairConnectionEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1

The Pair Connection entry.

Indexes

pairConnectionTcpAliveCheck

Column Syntax OID

The TCP alive check time.
0 min: TCP connection will not be closed if the
TCP connection becomes idle.
1 to 99 min: The NPort 6000 series device server
automatically closes the TCP connection if there is
no TCP activity…

pairConnectionDestinationAddress

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.1

pairConnectionSecure

If Secure is enabled, the Ethernet data will be
encrypted using SSL.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.2

The Pair Connection 'Master' will contact the
network host that has the specified IP address.

pairConnectionDestinationPort

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.3

Data will be transmitted through the specified port
number. Note that you must configure the same TCP
port number for the device server acting as the Pair
Connection 'Slave.'

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.4

pairConnectionTcpPort

This port number must be the same port number that was
set up for the Pair Connection 'Master' device
server.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.5

ethernetModemTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1 · 1 row entry · 2 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk ethernetModemTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::ethernetModemTable'

The Ethernet Modem table.

ethernetModemEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1

The Ethernet Modem entry.

Indexes

Column	Syntax	OID
ethernetModemTcpAliveCheck The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activit…	Integer32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.1`
ethernetModemTcpPort The local TCP port used to listen for incoming calls from a remote ethernet modem.	Integer32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.2`

terminalTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1 · 1 row entry · 19 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk terminalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::terminalTable'

The Terminal Application table.

terminalEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1

The Terminal Application entry.

Indexes

Column Syntax OID

terminalTcpAliveCheck

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.1

terminalInactivityTime

0 min: TCP connection will not be closed if the
serial line becomes idle.
0-99 min: The NPort 6000 series device server
automatically closes the TCP connection if there is
no serial data activity for the given time. Af…

terminalPrimaryHostAddress

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.2

terminalAutoLinkProtocol

If Auto-Link protocol is set to 'None,' the NPort
6000 series device server will not connect to the
host automatically. If Auto-Link protocol is set to
'Telnet,' the NPort 6000 series device server will
connect to the h…

Enumerationr/w

Enumerated Values:

0	none
1	telnet
2	rlogin

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.3

If specified, designates a 'permanent' host to
which the terminal will always be connected.

terminalSecondHostAddress

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.4

If specified, designates a 'permanent' host to
which the terminal will always be connected.

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.5

terminalTelnetTcpPort

By default, the Telnet TCP port number is set to
23, which is the default TCP port number for Telnet.
If you need to telnet to this NPort 6000 series
device server's serial port, set the Telnet TCP port
to a different n…

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.6

terminalSshTcpPort

By default, the SSH TCP port number is set to 22,
which is the default TCP port number for SSH. If
you need to use SSH to connect to this NPort 6000
series device server's serial port, set the Telnet
TCP port to a diffe…

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.7

terminalType

Defines the terminal type for outgoing connections.

Constraints:
range: 0-8

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.8

terminalMaxSessions

Configure the max. number of sessions.

Integer32r/w

Constraints:
range: 1-8

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.9

terminalChangeSession

Defines the control character used to change the terminal
session.

Constraints:
range: 0-2

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.10

terminalQuit

Defines the control character used to quit a terminal
session.

Constraints:
range: 0-2

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.11

terminalBreak

Defines the control character used to send a Telnet
BREAK message.

Constraints:
range: 0-2

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.12

terminalInterrupt

Defines the control character used to send a Telnet
INTERRUPT message.

terminalAuthenticationType

Constraints:
range: 0-2

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.13

The terminal authentication type.

Enumerationr/w

Enumerated Values:

0	none
1	local
2	radius
3	radius-local
4	local-radius
5	tacacsPlus
6	tacacsPlus-local
7	local-tacacsPlus

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.14

terminalTryNextAuth

Try next type on authentication denied or not

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.15

terminalAutoLoginPrompt

The prompt string for the automatic login ID. When the
NPort 6000 series device server receives this string
from a remote telnet/rlogin server, it will
automatically reply with the user ID.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.16

terminalPasswordPrompt

The prompt string for the automatic login password.
When the NPort 6000 series device server receives this
string from a remote telnet/rlogin server, it will
automatically reply with the user password.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.17

terminalLoginUserName

Terminal login ID for automatic login.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.18

terminalLoginPassword

Terminal login password for automatic login.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.19

reverseTerminalTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1 · 1 row entry · 6 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk reverseTerminalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::reverseTerminalTable'

The Reverse Terminal Application table.

reverseTerminalEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1

The Reverse Terminal Application entry.

Indexes

reverseTerminalTcpAliveCheck

Column Syntax OID

The TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection becomes idle.
1 to 99 min: The NPort 6000 series device server
automatically closes the TCP connection if there is
no TCP activi…

reverseTerminalInactivityTime

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.2

reverseTerminalTcpPort

Each of the NPort 6000 series device server's serial
ports are mapped to a TCP port.

reverseTerminalAuthenticationType

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.3

The reverse terminal authentication type.

Enumerationr/w

Enumerated Values:

0	none
1	local
2	radius
3	radius-local
4	local-radius
5	tacacsPlus
6	tacacsPlus-local
7	local-tacacsPlus

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.4

reverseTerminalTryNextAuth

Try next type on authentication denied or not

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.5

reverseTerminalMapKeys

If data received through NPort 6000 series device
server's Ethernet port is sent using the 'enter'
command, the data will be transmitted out through
the serial port with an added
1. 'carriage return + line feed' if you …

Enumerationr/w

Enumerated Values:

0	cr-lf
1	cr
2	lf

.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.6

printerTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1 · 1 row entry · 6 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk printerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::printerTable'

The Printer Application table.

printerEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1

The Printer Application entry.

Indexes

Column Syntax OID

printerTcpAliveCheck

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.1

printerTcpPort

The host uses this value to determine the Group to
which the printer attached to this serial port
belongs. These values are fixed, and cannot be
changed by the user.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.2

printerGroup

Groups printers attached to different ports.
Printers in the same group will share the printing
load for printing requests to that group of
printers. E.g., setting the NPort 6000 series device
server's serial ports 1, 3…

Enumerationr/w

Enumerated Values:

0	group1
1	group2
2	group3
3	group4
4	group5
5	group6
6	group7
7	group8
8	group9
9	group10
10	group11
11	group12
12	group13
13	group14
14	group15
15	group16
16	group17
17	group18
18	group19
19	group20
20	group21
21	group22
22	group23
23	group24
24	group25
25	group26
26	group27
27	group28
28	group29
29	group30
30	group31
31	group32

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.3

printerQueueNameRaw

Specify the name of the print queue (in RAW mode).

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.4

printerQueueNameASCII

Specify the name of the print queue (in ASCII mode).

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.5

printerAppendFormFeed

Specify paging.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.6

dialTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1 · 1 row entry · 16 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk dialTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::dialTable'

The Dial In/Out table.

dialEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1

The Dial In/Out entry.

Indexes

Column Syntax OID

dialTERMBINMode

Select Yes to enable a Binary Terminal connection.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.1

dialPPPDMode

Select Yes to enable a PPPD connection.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.2

dialSLIPDMode

Select Yes to enable a SLIPD Terminal connection.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.3

dialAuthType

The dial in/out authentication type.

Enumerationr/w

Enumerated Values:

0	none
1	local
2	radius
3	radius-local
4	local-radius
5	tacacsPlus
6	tacacsPlus-local
7	local-tacacsPlus

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.4

dialTryNextAuth

Try next type on authentication denied or not

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.5

dialDisconnectBy

If this field is set to 'dcd-off,' the connection
will be disconnected when the DCD signal is off.
If this field is set to 'dsr-off,' the connection
will be disconnected when the DSR signal is off.

Enumerationr/w

Enumerated Values:

0	none
2	dcd-off
4	dsr-off

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.6

dialDestinationIpAddress

Destination IP address is the IP address of the
remote dial-in/dial-out server.

Type Constraints:
range: 4

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.7

dialSourceIpAddress

Source IP address is IP address of this serial
port. The NPort 6000 series device server will
automatically assign an IP address for the port.
We recommend leaving this field blank.

Type Constraints:
range: 4

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.8

dialIpNetmask

The IP netmask used for dial-in/dial-out networks
(PPP or SLIP).

Type Constraints:
range: 4

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.9

dialTcpIpCompression

Depends on whether the remote user's application
requests compression.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.10

dialInactivityTime

0 ms: TCP connection will not be closed if the
serial line becomes idle.
1-65535 ms: The NPort 6000 series device server
automatically closes the TCP connection if there is
no serial data activity for the given time. A…

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.11

dialLinkQualityReport

Choose YES if you are using software to collect Link quality
information.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.12

dialUsername

Dial-out user ID account.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.13

dialPassword

Dial-out user password.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.14

dialIncomingPAPCheck

The Dial in/out incoming PAP check type.

Enumerationr/w

Enumerated Values:

0	none
1	local
2	radius
3	radius-local
4	local-radius
5	tacacsPlus
6	tacacsPlus-local
7	local-tacacsPlus

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.15

dialIncomingTryNextAuth

Try next type on authentication denied or not

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.16

dataPackingPortTable

table

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1 · 1 row entry · 7 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk dataPackingPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::dataPackingPortTable'

The Data Packing table.

dataPackingPortEntry row .1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1

The Data Packing entry.

Indexes

Column Syntax OID

portPacketLength

If the value is 0, the Delimiter Process will be
used, regardless of the length of the data
packet. If the data length (in bytes) matches the
configured value, the data will be forced out. The
data length can be configu…

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.1

portDelimiter1Enable

Enable the first delimiter character.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.2

portDelimiter1

The first delimiter character, in hex decimal.

Constraints:
range: 0-2

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.3

portDelimiter2Enable

Enable the second delimiter character.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.4

portDelimiter2

The second delimiter character, in hex decimal.

Constraints:
range: 0-2

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.5

portDelimiterProcess

'delimiterAddOne' or 'delimiterAddTwo': The data
will be transmitted when an additional byte (for
'delimiterAddOne'), or an additional 2 bytes (for
'delimiterAddTwo') of data is received after
receiving the Delimiter.
'…

Enumerationr/w

Enumerated Values:

1	doNothing
2	delimiterAddOne
4	delimiterAddTwo
8	stripDelimiter

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.6

portForceTransmit

0: Disable the force transmit timeout.
1 to 65535: Forces the NPort 6000 series device
server's TCP/IP protocol software to try to pack
serial data received during the specified time into
the same data frame.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.7

comParamPortTable

table

.1.3.6.1.4.1.8691.2.8.1.4.2.1 · 1 row entry · 11 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk comParamPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::comParamPortTable'

The Communication Parameters table.

comParamPortEntry row .1.3.6.1.4.1.8691.2.8.1.4.2.1.1

The Communication Parameters entry.

Indexes

Column Syntax OID

portAlias

Port alias is included to allow easy identification of
the serial devices that are connected to NPort 6000
series device server's serial port.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.1

portInterface

The serial interface that the port works on.

Enumerationr/w

Enumerated Values:

0	rs-232
1	rs-422
2	rs-485-2-wire
3	rs-485-4-wire

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.2

portBaudRate

The port's speed in bits per second. You can choose
a standard baud rate by indexing.

Enumerationr/w

Enumerated Values:

0	b50
1	b75
2	b110
3	b134
4	b150
5	b300
6	b600
7	b1200
8	b1800
9	b2400
10	b4800
11	b7200
12	b9600
13	b19200
14	b38400
15	b57600
16	b115200
17	b230400
18	b460800
19	b921600

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.3

portBaudRateManual

The port's speed in bits per second. You can
specify a baud rate manually.

Integer32r/w

Constraints:
range: 50-921600

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.4

portDataBits

The number of bits in a character for the port.

Enumerationr/w

Enumerated Values:

0	bits-5
1	bits-6
2	bits-7
3	bits-8

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.5

portStopBits

The number of stop bits for the port.

Enumerationr/w

Enumerated Values:

0	bits-1
1	bits-1dot5
2	bits-2

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.6

portParity

The parity bit for the port.

Enumerationr/w

Enumerated Values:

0	none
1	odd
2	even
3	mark
4	space

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.7

portFlowControl

The flow-control method for the port.

Enumerationr/w

Enumerated Values:

0	none
1	rts-cts
2	xon-xoff
3	dtr-dsr
4	rts-toggle

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.8

portFIFO

Enable or disable the port's FIFO.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.9

portOnDelay

The port's RTS toggle On delay time (ms).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.10

portOffDelay

The port's RTS toggle Off delay time (ms).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.11

dataBufferingPortTable

table

.1.3.6.1.4.1.8691.2.8.1.4.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk dataBufferingPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::dataBufferingPortTable'

The Data Buffering/Log table.

dataBufferingPortEntry row .1.3.6.1.4.1.8691.2.8.1.4.3.1.1

The Data Buffering/Log entry.

Indexes

Column Syntax OID

portBufferingEnable

Enable off-line port buffering.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.1

portBufferingLocation

The location of off-line port buffering.
Note: NPort 6150 can not be set as sdCard.

Enumerationr/w

Enumerated Values:

0	memory
1	sdCard

.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.2

portBufferingSDFileSize

The maximum file size of off-line port buffering,
in MBytes, if the location is set to 'sdCard.'
Note: NPort 6150 do not support write access.

portSerialDataLoggingEnable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.3

Enable or disable serial data logging for the port.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.4

modemSettingsPortTable

table

.1.3.6.1.4.1.8691.2.8.1.4.4.1 · 1 row entry · 4 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk modemSettingsPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::modemSettingsPortTable'

The Modem Settings table.

modemSettingsPortEntry row .1.3.6.1.4.1.8691.2.8.1.4.4.1.1

The Modem Settings entry.

Indexes

Column Syntax OID

portEnableModem

Enable or disable modem for this port.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.1

portInitialString

Set the modem's initial string to establish the
connection. E.g., 'AT&S0=1' for auto-answer.

Constraints:
range: 0-24

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.2

portDialUp

Set the modem's dial-up AT command string.

Constraints:
range: 0-8

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.3

portPhoneNumber

Set the number used to dial out.

Constraints:
range: 0-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.4

cipherSettingsPortTable

table

.1.3.6.1.4.1.8691.2.8.1.4.5.1 · 1 row entry · 2 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk cipherSettingsPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::cipherSettingsPortTable'

The Cipher Settings table.

cipherSettingsPortEntry row .1.3.6.1.4.1.8691.2.8.1.4.5.1.1

The Cipher Settings entry.

Indexes

Column	Syntax	OID
sslCipherSort SSL cipher sorting. The format is '2,0,1,3,5,6,8,9,4,7' for example. The index mapping of each cipher method is shown blow. EDH-RSA-DES-CBC3-SHA(2) has the highest priority in this example. DHE-RSA-AES256-SHA(0), …	SNMPv2-TCDisplayStringr/w Constraints: `range: 53-53` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.4.5.1.1.1`
sshCipherSort SSL cipher sorting. The format is '2,0,1,3,5,4,6,7' for example. The index mapping of each cipher method is shown blow. aes192-cbc(2) has the highest priority in this example. aes128-cbc(0), 3dec-cbc(1), aes192…	SNMPv2-TCDisplayStringr/w Constraints: `range: 16-16` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.4.5.1.1.2`

accessibleIpListTable

table

.1.3.6.1.4.1.8691.2.8.1.5.1.1.2 · 1 row entry · 4 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk accessibleIpListTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::accessibleIpListTable'

Accessible IP List table.

accessibleIpListEntry row .1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1

Accessible IP List entry.

Indexes

accessibleIpListIndex

Column Syntax OID

accessibleIpListIndex

Accessible IP List index.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.1

activeAccessibleIpList

Enable or disable this accessible IP entry.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.2

accessibleIpListAddress

Accessible IP address. This value can be the IP address of a
single host if the netmask is set to '255.255.255.255,'
or it can be a network address.

Constraints:
range: 0-40

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.3

accessibleIpListNetmask

Accessible IP address netmask. The IP address and
netmask are used to specify a group of remote hosts.

Constraints:
range: 0-15

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.4

hostTableTable

table

.1.3.6.1.4.1.8691.2.8.1.5.1.4.1 · 1 row entry · 3 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk hostTableTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::hostTableTable'

Host Table.

hostTableEntry row .1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1

Host Table entry.

Indexes

hostTableIndex

Column	Syntax	OID
hostTableIndex The Host Table index.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.1`
hostName The host name of the host table entry.	SNMPv2-TCDisplayStringr/w Constraints: `range: 0-16` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.2`
hostIpAddress Related IP address of the host table entry.	SNMPv2-TCDisplayStringr/w Constraints: `range: 0-40` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.3`

routeTableTable

table

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1 · 1 row entry · 6 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk routeTableTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::routeTableTable'

Route Table.

routeTableEntry row .1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1

Route Table entry.

Indexes

routeTableIndex

Column Syntax OID

routeTableIndex

The Route Table index.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.1

gatewayRouteTable

The gateway property of the route table entry.

Type Constraints:
range: 4

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.2

destinationRouteTable

The destination IP address of the route table entry.
This value can be the IP address of a single host if
the netmask set to
'255.255.255.255,' or it can be a network address.

Type Constraints:
range: 4

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.3

netmaskRouteTable

The destination netmask of the route table entry.

Type Constraints:
range: 4

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.4

metricRouteTable

The routing metric for this route. The semantics of
this metric are determined by the routing-protocol.
Normally, it represents the cost for the destination.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.5

interfaceRouteTable

The value that identifies the local interface
through which the next hop of this route should be
reached.

Enumerationr/w

Enumerated Values:

0	port1
1	port2
2	port3
3	port4
4	port5
5	port6
6	port7
7	port8
8	port9
9	port10
10	port11
11	port12
12	port13
13	port14
14	port15
15	port16
16	port17
17	port18
18	port19
19	port20
20	port21
21	port22
22	port23
23	port24
24	port25
25	port26
26	port27
27	port28
28	port29
29	port30
30	port31
31	port32
256	lan

.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.6

userTableTable

table

.1.3.6.1.4.1.8691.2.8.1.5.1.6.1 · 1 row entry · 4 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk userTableTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::userTableTable'

User Table.

userTableEntry row .1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1

User Table entry.

Indexes

userTableIndex

Column	Syntax	OID
userTableIndex The User Table index.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.1`
userNameUserTable The user name of this entry.	SNMPv2-TCDisplayStringr/w Constraints: `range: 0-16` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.2`
passwordUserTable The password of this user entry.	SNMPv2-TCDisplayStringr/w Constraints: `range: 0-16` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.3`
phoneNumberUserTable The phone number of this user entry.	SNMPv2-TCDisplayStringr/w Constraints: `range: 0-16` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.4`

portEventSettingsTable

table

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1 · 1 row entry · 8 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk portEventSettingsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::portEventSettingsTable'

Port Event Settings Table.

portEventSettingsEntry row .1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1

Port Event Settings entry.

Indexes

Column Syntax OID

mailDCDchange

A change in the DCD (Data Carrier Detect) signal
indicates that the modem connection status has
changed. For example, if the DCD signal changes to
low, it indicates that the connection line is down.
When the DCD signal …

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.1

trapDCDchange

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.2

alarmDCDchange

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.3

smsDCDchange

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.4

mailDSRchange

A change in the DSR (Data Set Ready) signal
indicates that the data communication equipment is
powered off. For example, if the DSR signal changes
to low, it indicates that the data communication
equipment is powered do…

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.5

trapDSRchange

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.6

alarmDSRchange

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.7

smsDSRchange

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.8

userAccountTable

table

.1.3.6.1.4.1.8691.2.8.1.5.4.2.1 · 1 row entry · 4 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk userAccountTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::userAccountTable'

User account list

userAccountEntry row .1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1

User account list entry

Indexes

userAccountIndex

Column Syntax OID

userAccountIndex

The Host Table index.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.1

activeUserAccount

The user account is activate or not.

Enumerationr/w

Enumerated Values:

0	non_active
1	avtive

.1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.2

accountName

Name of user account

Constraints:
range: 1-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.3

accountGroupName

Group name of user account

Constraints:
range: 1-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.5.4.2.1.1.4

accessPermissionTable

table

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1 · 1 row entry · 7 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk accessPermissionTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::accessPermissionTable'

Access permission list

accessPermissionEntry row .1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1

Access permission list entry

Indexes

groupName

Column Syntax OID

groupName

Group name

Constraints:
range: 1-16

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.1

networkConfig

Access permission of network configuration group

Enumerationr/w

Enumerated Values:

0	no-display
1	read-only
2	read-write

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.2

serialConfig

Access permission of serial configuration group

Enumerationr/w

Enumerated Values:

0	no-display
1	read-only
2	read-write

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.3

systemConfig

Access permission of system configuration group

Enumerationr/w

Enumerated Values:

0	no-display
1	read-only
2	read-write

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.4

adminConfig

Access permission of administration group

Enumerationr/w

Enumerated Values:

0	no-display
1	read-only
2	read-write

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.5

monitorLogWarning

Access permission of log monitoring group

Enumerationr/w

Enumerated Values:

0	no-display
1	read-only
2	read-write

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.6

commonSetting

Access permission of common setting group

Enumerationr/w

Enumerated Values:

0	no-display
1	read-only
2	read-write

.1.3.6.1.4.1.8691.2.8.1.5.4.3.1.1.7

monitorRemoteIpTable

table

.1.3.6.1.4.1.8691.2.8.1.6.1.1 · 1 row entry · 3 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk monitorRemoteIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::monitorRemoteIpTable'

Serial to Network Connections Remote IP table.

monitorRemoteIpEntry row .1.3.6.1.4.1.8691.2.8.1.6.1.1.1

Serial to Network Connections Remote IP entry.

Indexes

portIndex remoteIpIndex

Column	Syntax	OID
remoteIpIndex Serial to Network Connections Remote IP index.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.6.1.1.1.1`
monitorRemoteIp The remote IP currently connecting to this port.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.6.1.1.1.2`
monitorCipher Currently used cipher for this connection if secure mode is enabled.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.8691.2.8.1.6.1.1.1.3`

monitorSerialPortStatusTable

table

.1.3.6.1.4.1.8691.2.8.1.6.2.1 · 1 row entry · 9 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk monitorSerialPortStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::monitorSerialPortStatusTable'

Serial Port Status table.

monitorSerialPortStatusEntry row .1.3.6.1.4.1.8691.2.8.1.6.2.1.1

Serial Port Status entry.

Indexes

Column Syntax OID

monitorTxCount

View the number of bytes transmitted from the port
since the last time the port was initialized.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.1

monitorRxCount

View the number of bytes received by the port since
the last time the port was initialized.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.2

monitorTxTotalCount

View the number of bytes transmitted from the port
since the last time the system was initialized.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.3

monitorRxTotalCount

View the number of bytes received by the port since
the last time the system was initialized.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.4

monitorDSR

View the current DSR status of this port.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.5

monitorDTR

View the current DTR status of this port.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.6

monitorRTS

View the current RTS status of this port.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.7

monitorCTS

View the current CTS status of this port.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.8

monitorDCD

View the current DCD status of this port.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.9

monitorSerialPortErrorCountTable

table

.1.3.6.1.4.1.8691.2.8.1.6.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk monitorSerialPortErrorCountTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::monitorSerialPortErrorCountTable'

Serial Port Error Count table.

monitorSerialPortErrorCountEntry row .1.3.6.1.4.1.8691.2.8.1.6.3.1.1

Serial Port Error Count entry.

Indexes

Column	Syntax	OID
monitorErrorCountFrame View the number of 'Frame' errors for this port.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.1`
monitorErrorCountParity View the number of 'Parity' errors for this port.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.2`
monitorErrorCountOverrun View the number of 'Overrun' errors for this port.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.3`
monitorErrorCountBreak View the number of 'Break' errors for this port.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.4`

monitorSerialPortSettingsTable

table

.1.3.6.1.4.1.8691.2.8.1.6.4.1 · 1 row entry · 10 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk monitorSerialPortSettingsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::monitorSerialPortSettingsTable'

Serial Port Settings table.

monitorSerialPortSettingsEntry row .1.3.6.1.4.1.8691.2.8.1.6.4.1.1

Serial Port Settings entry.

Indexes

Column Syntax OID

monitorBaudRate

View the current baudrate of the port.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.1

monitorDataBits

View the number of bits per byte for the port.

Enumeration

Enumerated Values:

0	bits-5
1	bits-6
2	bits-7
3	bits-8

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.2

monitorStopBits

View the number of stop bits for the port.

monitorXONXOFFFlowControl

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.3

monitorParity

View the parity bit for the port.

Enumeration

Enumerated Values:

0	none
8	odd
24	even
40	mark
56	space

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.4

monitorRTSCTSFlowControl

View if the port is using RTS/CTS flow control.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.5

View if the port is using XON/XOFF flow control.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.6

monitorDTRDSRFlowControl

View if the port is using DTR/DSR flow control.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.7

monitorRTSToggleFlowControl

View if the port is using RTS toggle flow control.

Enumeration

Enumerated Values:

0	off
1	on

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.8

monitorFIFO

View FIFO status of this port.

Enumeration

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.9

monitorInterface

View the serial interface that the port is using.

Enumeration

Enumerated Values:

0	rs-232
1	rs-422
2	rs-485-2-wire
3	rs-485-4-wire

.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.10

monitorSerialPortBufferingTable

table

.1.3.6.1.4.1.8691.2.8.1.6.5.1 · 1 row entry · 1 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk monitorSerialPortBufferingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::monitorSerialPortBufferingTable'

Serial Port Buffering table.

monitorSerialPortBufferingEntry row .1.3.6.1.4.1.8691.2.8.1.6.5.1.1

Serial Port Settings entry.

Indexes

Column	Syntax	OID
monitorBuffering View length of buffered data for the port. The length unit is byte.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.8691.2.8.1.6.5.1.1.1`

portDCDChangedStatusTable

table

.1.3.6.1.4.1.8691.2.8.1.6.6.7 · 1 row entry · 2 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk portDCDChangedStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::portDCDChangedStatusTable'

DCD changed table.

portDCDChangedStatusEntry row .1.3.6.1.4.1.8691.2.8.1.6.6.7.1

DCD changed entry.

Indexes

portDCDChangedAcknowledge

Column Syntax OID

portDCDChangedStatus

The relay dout status of the event that the DCD signal
of the port is changed.

Enumeration

Enumerated Values:

0	none
1	alarm
2	alarm-Acked

.1.3.6.1.4.1.8691.2.8.1.6.6.7.1.1

Acknowledge the event that the DCD signal of the port
is changed. Acknowledgement will clear the d-out
alarm before you can actually fix the problem.

Enumerationr/w

Enumerated Values:

acked

.1.3.6.1.4.1.8691.2.8.1.6.6.7.1.2

portDSRChangedStatusTable

table

.1.3.6.1.4.1.8691.2.8.1.6.6.8 · 1 row entry · 2 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk portDSRChangedStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::portDSRChangedStatusTable'

DSR changed Table.

portDSRChangedStatusEntry row .1.3.6.1.4.1.8691.2.8.1.6.6.8.1

DSR changed entry.

Indexes

portDSRChangedAcknowledge

Column Syntax OID

portDSRChangedStatus

The relay dout status of the event that the DSR signal
of the port is changed.

Enumeration

Enumerated Values:

0	none
1	alarm
2	alarm-Acked

.1.3.6.1.4.1.8691.2.8.1.6.6.8.1.1

Acknowledge the event that the DSR signal of the port
is changed. Acknowledgement will clear the d-out
alarm before you can actually fix the problem.

Enumerationr/w

Enumerated Values:

acked

.1.3.6.1.4.1.8691.2.8.1.6.6.8.1.2

spanningTreePortStatusTable

table

.1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4 · 1 row entry · 5 columns

Open in standard view

Uses the moxa variant from /opt/observium/mibs/moxa.

Command help

Walk spanningTreePortStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MOXA-NP6000-MIB' -M '/opt/observium/mibs/moxa:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MOXA-NP6000-MIB::spanningTreePortStatusTable'

The spanning tree port status table.

spanningTreePortStatusEntry row .1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1

The spanning tree port entry.

Indexes

spanningTreePortStatusIndex

Column Syntax OID

spanningTreePortStatusIndex

The index of spanning tree table.

spanningTreePortEnableStatus

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.1

This displays whether or not spanning tree protocol is enabled for this port.

Enumeration

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.2

spanningTreePortRole

This port's role in spanning tree protocol.

spanningTreePortDesignatedBridge

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.3

This port's designated bridge ID.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8691.2.8.1.6.7.1.2.4.1.4

spanningTreePortStatus

The port status of spanning tree protocol.