MEF-R-MIB Table View

This table defines the MEF BW profile attributes. The profile can be
defined either directly to an entity i.e. UNI or EVC or per EVC.CoS as
follows:
          
UNI
When the BW profile is applied to a UNI, the ' CoSProfileIndex'
attribute's value must be set to 'none'.
          
EVC
When the BW profile is applied to an EVC, the ' nCoSProfileIndex'
attribute's value must be set to 'none'.
          
EVC.CoS
When the BW profile is applied to an EVC and CoS, the ' CoSProfileIndex'
attribute's value must be set to the
correct CoS ID.
          
A bandwidth profile outlines the service guarantees that the SP will provide
by defining traffic types and amounts of each traffic type that subscribers
can send into the SP's network.

bwProfileEntry row .1.3.6.1.4.1.164.20.8.1.3.1.1

A conceptual row where each row contains one BW profile attributes.

Indexes

bwProfileID bwProfileIndex

Column	Syntax	OID
bwProfileID This attribute defines the BW Profile ID. The BW profile ID must be greater than '0'.	TCVTIdV2	.1.3.6.1.4.1.164.20.8.1.3.1.1.1
bwProfileIndex This attribute defines the BW Profile index. The BW profile index is a 'running index' denoting more than one profile e.g. High & Low, specified for this BW profile. The BW profile index must be greater than '0'.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.1.1.2
bwProfileRowStatus This attribute is used to create a new row or to delete an existing row in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.3.1.1.3
bwProfileCIR This attribute defines the Committed Information Rate (CIR) BW. CIR is the average rate up to which packets are marked Green.	KbpsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.1.1.4
bwProfileCBS This attribute defines the Committed Burst Size (CBS) for the CoS. CBS is the maximum number of bytes allowed for incoming packets to burst above CIR, but still marked Green.	OctetsTCBurstSizeV2r/w	.1.3.6.1.4.1.164.20.8.1.3.1.1.5
bwProfileEIR This attribute defines the Excessive Information Rate (EIR) BW. The EIR is greater or equal to CIR. Packets that exceed the CIR but are below the EIR are marked Yellow.	KbpsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.1.1.8
bwProfileEBS This attribute defines the Excessive Burst Size (EBS) for the CoS. EBS is the maximum number of bytes allowed for incoming packets to burst above EIR, but still marked Yellow.	OctetsTCBurstSizeV2r/w	.1.3.6.1.4.1.164.20.8.1.3.1.1.9
bwProfileColorAware This attribute defines whether the policing function assumes ingress frames are already colored and must be treated, or not. This attribute implements the MEF's Color Mode (CM) attribute. true Frames are …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.8.1.3.1.1.12
bwProfileColorAwareAdmissionOption This attribute defines the admission options for Yellow Colored Frames. A service may be defined to admit more yellow frames into the network when the volume of the green frames does not consume all available CIR bandwi…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.8.1.3.1.1.13
bwProfileName This attribute defines the name assigned to BW profile.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.8.1.3.1.1.14
bwProfileGranularity This attribute defines BW profile Granularity.	Enumerationr/w Enumerated Values: 2 r64kbps 3 r1Mbps 4 r10Mbps 5 r100Mbps	.1.3.6.1.4.1.164.20.8.1.3.1.1.15
bwProfilePolicedTraffic This attribute defines the policed traffic type.	Enumerationr/w Enumerated Values: 2 all 3 broadcast 4 multicast 5 unknownUnicast 6 broadcastAndMulticast 7 broadcastAndMulticastAndUnknownUnicast	.1.3.6.1.4.1.164.20.8.1.3.1.1.16
bwProfileCompensation This attribute defines the layer1 overhead (preamble and IFG) and the overhead for the added VLAN header in case of stacking. The compensation enable the policer to charge the bucket also for these overheads. Using this…	OctetsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.1.1.17

This table contains envelope bandwidth profiles as defined in
MEF 10.3 section 12.

envelopeBwProfileEntry row .1.3.6.1.4.1.164.20.8.1.3.2.1

An entry in envelope BW profile table.

A row cannot be deleted if the profile is associated to a flow.

When a row is deleted all the corresponding rows in the
envelopeBwProfileCoSTable are auto…

Indexes

envelopeBwProfileIndex

Column	Syntax	OID
envelopeBwProfileIndex A unique number as profile identifier.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.2.1.1
envelopeBwProfileName A meaningful printable profile name.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.164.20.8.1.3.2.1.2
envelopeBwProfileRowStatus This object enables creation and deletion of profiles.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.3.2.1.3
envelopeBwProfileCouplingFlagPolicy Overall policy for the coupling flags. When set to sharingExcessBw(2) or to uncoupledBwSharing(3) the object envelopeBwProfileCouplingFlag0 is ignored and the object/s envelopeBwProfileCosCouplingFlag are…	Enumerationr/w Enumerated Values: 1 manual 2 sharingExcessBw 3 uncoupledBwSharing	.1.3.6.1.4.1.164.20.8.1.3.2.1.4
envelopeBwProfileCouplingFlag0 This parameter determines whether or not overflow tokens not used for service frames declared Green can be used as Yellow tokens. When set to 1 - Green tokens that are unconsumed by any CoS are passed to …	Unsigned32r/w Constraints: range: 0-1	.1.3.6.1.4.1.164.20.8.1.3.2.1.5
envelopeBwProfileColorMode The color mode that is used for the service.	Enumerationr/w Enumerated Values: 1 colorAware 2 colorBlind	.1.3.6.1.4.1.164.20.8.1.3.2.1.6
envelopeBwProfileCompensation This attribute allows to take into consideration the overhead added to transmitted frames e.g preamble, IFG, VLAN stacking. The compensation enables the policer to charge the bucket also for these overhea…	bytesUnsigned32r/w Constraints: range: 0-63	.1.3.6.1.4.1.164.20.8.1.3.2.1.7

This table contains envelope bandwidth profiles, at the CoS level.

envelopeBwProfileCosEntry row .1.3.6.1.4.1.164.20.8.1.3.3.1

An entry in envelope BW profile CoS table.

When a row is created, the envelopeBwProfileIndex must point to an
already existing row of envelopeBwProfileTable.

A row cannot be deleted if the prof…

Indexes

envelopeBwProfileIndex envelopeBwProfileCosIndex

Column	Syntax	OID
envelopeBwProfileCosIndex The CoS to which the configuration in this table applies.	Unsigned32 Constraints: range: 0-7	.1.3.6.1.4.1.164.20.8.1.3.3.1.1
envelopeBwProfileCosRowStatus This object enables creation and deletion of CoS profiles.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.3.3.1.2
envelopeBwProfileCosCir This attribute defines the average rate of service frames that are declared Green by the BW profile.	kbpsSNMPv2-SMIGauge32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.3.1.3
envelopeBwProfileCosCirMax This attribute limits the rate of tokens added to the committed token bucket (Green bucket). The value of this object must be equal or greater than envelopeBwProfileCosCir.	kbpsSNMPv2-SMIGauge32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.3.1.4
envelopeBwProfileCosCbs This attribute defines the maximum number of bytes available for a burst of service frames sent at the UNI line rate that are declared Green by the BW profile.	bytesSNMPv2-SMIGauge32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.3.1.5
envelopeBwProfileCosEir This attribute defines the average rate of service frames that are declared Yellow by the BW profile.	kbpsSNMPv2-SMIGauge32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.3.1.6
envelopeBwProfileCosEirMax This attribute limits the rate of tokens added to the excess token bucket (Yellow bucket). The value of this object must be equal or greater than envelopeBwProfileCosEir.	kbpsSNMPv2-SMIGauge32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.3.1.7
envelopeBwProfileCosEbs This attribute defines the maximum number of bytes available for a burst of service frames sent at the UNI line rate that are declared Yellow by the BW profile.	bytesSNMPv2-SMIGauge32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.3.3.1.8
envelopeBwProfileCoSCouplingFlag This parameter determines whether or not overflow tokens not used for service frames declared Green can be used as Yellow tokens. When set to 1 - unconsumed tokens are passed from the Green bucket to the …	Unsigned32r/w Constraints: range: 0-1	.1.3.6.1.4.1.164.20.8.1.3.3.1.9

This table defines the MEF CP attributes and behavior. It defines whether
a specific Control Protocol MAC address must be discarded, peered (i.e.
processed) or tunneled i.e. pushed forward). Note that a profile can
apply to either a UNI or an EVC and hence not all attributes apply to
both cases.

cPProfileEntry row .1.3.6.1.4.1.164.20.8.1.4.1.1

A conceptual row where each row contains one CP attributes.

Indexes

cPProfileIndex cPProfileRunningIndex

Column	Syntax	OID
cPProfileIndex Defines the CP Profile ID.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.164.20.8.1.4.1.1.1
cPProfileRunningIndex This attribute defines a running index for each CP MAC address. From value 0x4000001 (except 0x7FFFFFFF which indicates a default entry in the CP Profile)this profile will be used for Layer 2 protocol data units (PDUs)t…	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.164.20.8.1.4.1.1.2
cPProfileRowStatus This attribute is used to create a new row or to delete an existing row in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.4.1.1.3
cPProfileMacAddress This attribute defines the CP MAC address. When cPProfileMacProcessing equals to macChangeTunnel(5), this attribute defines the MAC address that replaces the MAC address of the original protocols (default MAC Address i…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.164.20.8.1.4.1.1.4
cPProfileMacProcessing This attribute defines the CP MAC address processing: ignore Ignore the MAC address since this MAC address will be processed by another 'rule' specified by e.g 'ceVlanId2EvcIngressMapMac'. …	Enumerationr/w Enumerated Values: 1 ignore 2 discard 3 peer 4 tunnel 5 macChangeTunnel	.1.3.6.1.4.1.164.20.8.1.4.1.1.5
cPProfileName The name of the CP Profile.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.8.1.4.1.1.6
cPProfileProtocol This attribute defines the Layer 2 protocol data units (PDUs) that are tunneled through a network.Values that are different than none(1) are relevant only for cPProfileRunningIndex greater than 0x4000000 (except 0x7FFFF…	Enumerationr/w Enumerated Values: 1 none 2 efmOam 3 portAuthentication 4 lacp 5 garp 6 stp 7 cdp 8 vtp 9 lldp 10 pvstp 11 pagp 14 udld 15 dtp 16 loopback	.1.3.6.1.4.1.164.20.8.1.4.1.1.7

This table shows L2CP statistics .Some protocols can be
distinguished by MAC,and some need parsing of other fields in addition to the MAC,
when more than one protocol uses the same MAC.

l2cpStatEntry row .1.3.6.1.4.1.164.20.8.1.4.2.1

An entry in the L2CP Statistics Table.

Indexes

l2cpStatPortIndex l2cpStatProtocol l2cpStatMacAddress

Column	Syntax	OID
l2cpStatPortIndex This object is an index of the specific port or interface. For an interface, ifIndex will be used.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.164.20.8.1.4.2.1.1
l2cpStatProtocol This object defines the Layer 2 protocol that is monitored . none(1) means Not Applicable . all(3) means total count of all the protocols that are transferred through a specific port(l2cpStatPortIndex).	Enumeration Enumerated Values: 1 none 2 other 3 all 4 efmOam 5 portAuthentication 6 lacp 7 garp 8 stp 9 cdp 10 vtp 11 lldp 12 pvstp 13 pagp 14 udld 15 dtp	.1.3.6.1.4.1.164.20.8.1.4.2.1.2
l2cpStatMacAddress This object defines the MAC Address of the protocol that is monitored. The address 00:00:00:00:00:00 means Not Applicable.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.164.20.8.1.4.2.1.3
l2cpStatEncapsulatedFrames This attribute displays the counted encapsulated Frames, before transferred via the provider's edge.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.4.2.1.4
l2cpStatDecapsulatedFrames This attribute displays the counted decapsulated Frames. These frames are retrieved to the original MAC after being encapsulated at the other customer side they were sent from.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.4.2.1.5

This table defines the MEF UNI attributes.

uniEntry row .1.3.6.1.4.1.164.20.8.1.5.1.1

A conceptual row where each row contains one UNI interface's
attributes.
Each row binds an Interface to a UNI.

Indexes

IF-MIBifIndex uniRunningIndex

Column	Syntax	OID
uniRunningIndex This attribute defines a running (UNI) index at the xNNI level.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.5.1.1.1
uniRowStatus This attribute is used to create a new row or to delete an existing row in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.5.1.1.2
uniLayer2CPProcessingProfile This attribute defines the Layer 2 Control Protocol Processing profile assigned to this UNI. If set to '0', no profile is assigned to this UNI.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.20.8.1.5.1.1.12
uniPerUniBWprofile This attribute defines the BW profile assigned to this UNI. If set to '0', no profile is assigned to this UNI.	TCVTIdV2r/w	.1.3.6.1.4.1.164.20.8.1.5.1.1.13
uniSpTagProtocolIdentifier Determines the Tag Protocol Identifier. Values: 8100 C-TAG 88a8 S-TAG.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.20.8.1.5.1.1.22
uniPacketColoring Determines whether the packet's computed color will be marked on Egress TAG, and if coloring will use DEI bit OR coloring will be based on CoS+color --> SP-Priority conversion table.	Enumerationr/w Enumerated Values: 1 disabled 2 deiColoring 3 priorityLsbColoring	.1.3.6.1.4.1.164.20.8.1.5.1.1.23
uniPerUniEgressAction This attribute defines the action that should be taken at the Egress side of this UNI.	Enumerationr/w Enumerated Values: 1 none 2 addSpTag	.1.3.6.1.4.1.164.20.8.1.5.1.1.27
uniQueueGroupName This attribute points to a queueGroupName of queueGroupTable.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.8.1.5.1.1.33
uniClassifierKey This bit map defines port classifier capabilities.	Bitsr/w Enumerated Values: 0 vlan 1 innerVlan 2 pBit 3 ipPrecedence 4 ipDscp 5 srcIpAddr 6 destIpAddr 7 legacy 8 dscp 9 macSrcAddr 10 macDestAddr 11 etherType 12 myMac 13 untagged	.1.3.6.1.4.1.164.20.8.1.5.1.1.36

This table defines the MEF Flow attributes.

flowEntry row .1.3.6.1.4.1.164.20.8.1.6.3.1

A conceptual row where each row contains one flow attributes.

Indexes

flowIdx1 flowIdx2

Column	Syntax	OID
flowIdx1 This attribute defines a unique Flow.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.1
flowIdx2 This attribute defines the type of the Bidirectional flow 1 - not in use (default - base flow) 201 - reverse flow 301 - via-1 flow 302 - via-2 flow 401 - Mirror-1 402 - Mirror-2 403 - Mirror-3 404 - Mirror-4	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.2
flowName This attribute defines a unique name assigned to the flow.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.8.1.6.3.1.3
flowRowStatus This attribute is used to create/delete rows of the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.6.3.1.4
flowBWprofile This attribute defines the BW profile(s) assigned to this flow. If set to '0', no profile is assigned to this flow.	TCVTIdV2r/w	.1.3.6.1.4.1.164.20.8.1.6.3.1.5
flowFixedCos This attribute defines the queue mapping that will be assigned to the flow in case it does not use the Marking profile assigned to the Uni. A value of 255 means that the flow will use the marking value according to the …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.6
flowCOSProfile This attribute defines the CoS profile assigned to this flow.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.7
flowQBlock This attribute defines the QBlock assigned to this flow. It can also be used as a pointer to a row of qProfileTable.	ObjectIdentifierr/w	.1.3.6.1.4.1.164.20.8.1.6.3.1.8
flowMappingProfile This attribute defines the Mapping profile assigned to this flow.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.9
flowFixedMarking This attribute defines the Marking value (0..63) that will be assigned to the flow in case it does not use the Marking profile.It is used only when add/push action is performed. A value of 255 means that the flow will u…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.10
flowMarkingProfile This attribute defines the Marking profile assigned to this flow. It is used only when add/push action is performed. In case of 'Copy',the value will be 2^32-1.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.11
flowOuterVlanTagging This attribute determines the behavior of the flow regarding it's Outer VLAN (the first after MAC Address): add - add VLAN to the frame at the Egress preserve - use the VLAN of the frame as the SP VLAN at the Egress rem…	Enumerationr/w Enumerated Values: 1 add 2 overwrite 3 preserve 4 remove	.1.3.6.1.4.1.164.20.8.1.6.3.1.12
flowOuterVlan This attribute defines the VLAN ID that is assigned in case that flowOuterVlanTagging value is add(1).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.13
flowInnerVlanTagging This attribute determines the behavior of the flow regarding it's Inner VLAN (the second after MAC Address): add - add VLAN to the frame at the Egress preserve - use the VLAN of the frame as the SP VLAN at the Egress. r…	Enumerationr/w Enumerated Values: 1 add 2 overwrite 3 preserve 4 remove	.1.3.6.1.4.1.164.20.8.1.6.3.1.14
flowInnerVlan This attribute defines the VLAN ID that is assigned to the frame in case that flowInnerVlanTagging value is add(1).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.15
flowEgressPort This attribute defines the egress port that is assigned to this flow. This value can represent also the slot/port in relevant devices.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.16
flowIngressPort This attribute defines the ingress port that is assigned to this flow. This value can represent also the slot/port in relevant devices. For a port-classifier flow i.e. when the value of flowClassiferType …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.17
flowInnerFixedMarking This attribute defines the Inner Marking value (0..63) that will be assigned to the flow in case it does not use the Marking profile.It is used only when add/push action is performed. A value of 255 means that the flow …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.18
flowInnerMarkingProfile This attribute defines the Inner Marking profile assigned to this flow. It is used only when add/push action is performed. In case of 'Copy',the value will be 2^32-1.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.19
flowDropAction This attribute defines whether All the frames classified to this flow will be dropped. enable(3)=Drop Action.	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.20.8.1.6.3.1.20
flowPriority This attribute defines the priority of the flow in case that more than one flow is associated with same specific Ingress Port. 0-Lowest priority.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.21
flowMarkOuterFixedMarking This attribute defines the outer Marking value (0..63) that will be assigned to the flow in case it does not use the Marking profile.It is used only when mark=swap action is performed. A value of 255 means that the flow…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.22
flowMarkOuterMarkingProfile This attribute defines the outer Marking profile assigned to this flow. It is used only when mark=swap action is performed. In case of 'Copy',the value will be 2^32-1. Applicable only when flowMarkOuterVlanTagging value…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.23
flowMarkInnerFixedMarking This attribute defines the Inner Marking value (0..63) that will be assigned to the flow in case it does not use the Inner Marking profile.It is used only when mark=swap action is performed. A value of 255 means that t…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.24
flowMarkInnerMarkingProfile This attribute defines the Inner Marking profile assigned to this flow. It is used only when mark=swap action is performed. In case of 'Copy',the value will be 2^32-1.Applicable only when flowMarkInnerVlanTagging value …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.25
flowMarkOuterVlanTagging This attribute determines the marking action of the flow regarding its Outer VLAN (the first after MAC Address).	Bitsr/w Enumerated Values: 0 overwritePbit 1 overwriteVlan 2 overwriteEtherType	.1.3.6.1.4.1.164.20.8.1.6.3.1.26
flowMarkOuterVlan This attribute defines the VLAN ID that is assigned in case that flowMarkOuterVlanTagging value is overwriteVlan(1).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.27
flowMarkInnerVlanTagging This attribute determines the marking action of the flow regarding it's Inner VLAN (the second after MAC Address).	Bitsr/w Enumerated Values: 0 overwritePbit 1 overwriteVlan 2 overwriteEtherType	.1.3.6.1.4.1.164.20.8.1.6.3.1.28
flowMarkInnerVlan This attribute defines the VLAN ID that is assigned in case that flowMarkInnerVlanTagging value is overwriteVlan(1).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.29
flowPolicerAggregate This parameter defines the group of the Policer Aggregate (agnGroupIdx from agnGroupTable when agnGroupCnfgIdx=2 and agnGroupComponentIdx=0xFFFF ). The value 0 means that no group/policer aggregate is connected to the f…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.30
flowMarkMacTagging This attribute determines the behavior (marking action)of the flow regarding its MAC Address.	Bitsr/w Enumerated Values: 0 swapMacSrcAndDst 1 overwriteSrcMac 2 overwriteDstMac	.1.3.6.1.4.1.164.20.8.1.6.3.1.32
flowMarkIpTagging This attribute determines the behavior (marking action)of flow regarding its IP Address.	Bitsr/w Enumerated Values: 0 swapIpSrcAndDst 1 overwriteSrcIp 2 overwriteDstIp	.1.3.6.1.4.1.164.20.8.1.6.3.1.33
flowLayer2CPProcessingProfile This attribute defines the L2CP Processing profile assigned to this flow. If set to '0', no profile is assigned.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.38
flowIngressColorMapping This attribute defines the flow ingress color mapping: 'green' and 'yellow' defines color directly 'colorProfile' defines color profile according to the .	Enumerationr/w Enumerated Values: 1 green 2 yellow 255 colorProfile	.1.3.6.1.4.1.164.20.8.1.6.3.1.39
flowIngressColorProfile This attribute defines the ingress color profile assigned to this flow. If set to '0', no profile is assigned.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.40
flowCosMapping This attribute defines flow CoS mapping. The value 0..7 indicates fixed CoS selection. The value 255 defines using of flowCosMappingProfile OBJECT belonging to this table (see below). …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.41
flowCosMappingProfile This attribute defines CoS mapping profile assigned to this flow.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.42
flowStatus This object displays the flow status. Bit 0 = '1' denotes that operational state of the flow is OK. This bit duplicates the flow ifOperStatus. It allows to get all status information by one access. Bit 1…	Bits Enumerated Values: 0 operStat 1 adminStatDown 2 ingressOperStatNotUp 3 egressOperStatNotUp 4 test 5 lackOfResources 6 cfmOamFailure 7 y1564Test 8 rfc2544Test 9 mef46Loop	.1.3.6.1.4.1.164.20.8.1.6.3.1.47
flowServiceIdName This attribute defines the Service ID name of this flow, if the flow is not associated with a Service the value is null. Upon setting a value, the agent creates an entry in serviceIdTable table.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.164.20.8.1.6.3.1.49
flowPolicerType This attribute defines the type of the policer (i.e. BW profile type) that is attached to the flow. regular(2) - the BW profile is indicated by flowBWprofile that points to an entry in bw…	Enumerationr/w Enumerated Values: 1 none 2 regular 3 aggregate 4 envelope 5 regularAccountingOnly	.1.3.6.1.4.1.164.20.8.1.6.3.1.51
flowMultiCosCounters This attribute defines a list of CoS values to which flow counters are allocated. This object is relevant only when flowPolicerType is set to none(1).	Bitsr/w Enumerated Values: 0 cos0 1 cos1 2 cos2 3 cos3 4 cos4 5 cos5 6 cos6 7 cos7	.1.3.6.1.4.1.164.20.8.1.6.3.1.52
flowClassifierType This attribute defines the type of the classifier used.	Enumerationr/w Enumerated Values: 1 flowClassifier 2 portClassifier	.1.3.6.1.4.1.164.20.8.1.6.3.1.53
flowIngressPortClassifier This attribute indicates the ingress port that is indirectly assigned to this flow (via a corresponding rule in a port classifier). When the ingress port is not known the value zero is returned. …	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.164.20.8.1.6.3.1.54
flowDscpMarkingProfile This attribute defines the DSCP marking profile assigned to this flow.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.3.1.55

This table map flows to a service (EVC).
Rows in this table are created by agent when:
flowServiceId is set, or
erpVlanServiceIdName is set, or
for each entry in serviceIdCmdTable.

serviceIdEntry row .1.3.6.1.4.1.164.20.8.1.6.4.2.1

Entry in the serviceIdTable.

Indexes

serviceIdName serviceIdRowPointer

Column	Syntax	OID
serviceIdName This attribute defines a unique service identification.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.164.20.8.1.6.4.2.1.1
serviceIdRowPointer This attribute holds the OID of the entity that associate. with the Service. For the flowTable the serviceIdRowPointer shall point to agnStringToIndexTable.	SNMPv2-TCRowPointer Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.164.20.8.1.6.4.2.1.2
serviceIdEntityType This attribute specify the type of the entity in a service.	Enumeration Enumerated Values: 1 flow 2 erpVlan 3 ma	.1.3.6.1.4.1.164.20.8.1.6.4.2.1.3
serviceIdRowStatus This attribute is used to create a new row or to delete an existing row in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.6.4.2.1.5

This table display the configuration parameters of
the Service automatic command.
for each entry in this table the agent shall create
an entry in serviceIdTable.

serviceIdCmdEntry row .1.3.6.1.4.1.164.20.8.1.6.4.3.1

Entry in the serviceIdCfmTable.

Indexes

serviceIdName

Column	Syntax	OID
serviceIdCmdRowStatus This RowStatus is used to create a row in the table possible value of the RowStatus are active(1), createAndGo(4).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.8.1.6.4.3.1.1
serviceIdCmdVlan This attribute represent the (outer) VLAN of the Service.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.4.3.1.2
serviceIdCmdInnerVlan This attribute represent the (inner) VLAN of the Service.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.4.3.1.3
serviceIdCmdPortIdx This attribute represent the port (ifIndex) of the Service.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.4.3.1.4

Table that holds a set of scalars as columns.

pmFlowCmdEntry row .1.3.6.1.4.1.164.20.8.1.6.6.1

An entry in table.

Indexes

pmFlowCmdIndex

Column	Syntax	OID
pmFlowCmdIndex This object used as index value=1.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.8.1.6.6.1.1
pmFlowCmdWithOAMTraffic This command is related to flow counters behavior. the action will be at the device level for all flows measurements to include or exclude the OAM traffic from the service traffic. yes(2) - command to include the OAM t…	Enumerationr/w Enumerated Values: 2 yes 3 no	.1.3.6.1.4.1.164.20.8.1.6.6.1.2